Question about Triumph Daytona 600 Motorcycles

1 Answer

Triumph Daytona 600 will not turn over

Having problems starting my Daytona 600. I pull the clutch in and press the start button but nothing at all happens, no turning over of the engine just nothing, this is intermittent and can happen anytime either from a cold start or after doing 100 miles. The battery is fine, it's getting worse as now it can sometimes take half a dozen tries of the clutch and starter button before it fires up, when before it would fire up the second try. thanks for your help.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Triumph Master
  • 40,028 Answers

Hi, Jordan_x_tur before testing any electrical component in the Starting System it is "IMPERATIVE" that you have a fully charged battery of 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a preliminary reading of 12.5 volts or more but little or zero amperage, the battery is faulty and must be replaced. AGM type batteries fall into this scenario more so than lead acid batteries.
1. Ignition Switch not in the "ON" position.
2. Engine Run Switch in the "OFF" position.
3. Check the battery terminals for damage or corrosion check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter.
4. Bank angle sensor needs a reset or is faulty.
5. FOB battery low or dead.
6. Faulty ignition switch.
7. Faulty starter button.
8. Faulty kickstand, clutch, neutral safety switch.
9. Security alarm needs a reset.
10. Starter relay, solenoid, starter have failed or circuit wiring faulty.
11. Starter armature or field coils have failed.
12. Main fuse or circuit breaker may be blown or faulty.
13. The electric starter is working but starter clutch has failed.
14. Check for engine trouble codes.
For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
Bike won start Not battery think
04 Daytona 600 Won start please help
Triumph 2003 Daytona 600 Service Manual
Hermys Tire Cycle Inc 2004 Triumph Genuine Tools and manuals Motorcycle...
Triumph Daytona 600 Owner Handbook Manual

Posted on Jul 04, 2017

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Benimur
  • 6966 Answers

SOURCE: Daytona 675 won't start

Hi,

Two possibilities:

  • starting relay. This could actually be bypassed/jumped to determine if the starter motor will turn:
  • starter motor. most likely carbon brush.
Just a start, do postback how things turned up or should you need additional information. Good luck and Thank you for using FixYa.

Posted on Nov 22, 2008

  • 66 Answers

SOURCE: kawasaki zzr400 (1994 model),streetfighter wont start

check starter solenoid.see if getting power to starter side when pressing button .if yes check if power to starter w/ test light when pressing button.if power there check starter,also motor, will it turn manually or is it seized.if no power to starter side of solenoid, jump across solenoid posts w/ a large screwdriver -motor will probaly turn over,w/ key on.if small wire to solenoid has power when pressing start,solenoid bad,if no power, wiring or start button bad.

Posted on Feb 16, 2009

ButtFuzz
  • 463 Answers

SOURCE: Xchallenge won't start when engine is hot.

Check tightness of bolt where (carb/FI) goes into intake, and where intake goes into engine. Check gaskets in those locations, if any. Sounds like heat is causing some material to distort, causing a vacuum leak.

Posted on Feb 27, 2009

  • 22 Answers

SOURCE: 93 katana 600 wont start

Take one of the plugs out and hold it against the head while the engine cranks. You should get decent spark. If not, you have an ignition problem. If it gets decent spark, try spraying some starting fluid into the air cleaner box. If the engine starts up and runs for a couple seconds, you have a fuel delivery problem.

Posted on Feb 27, 2009

ollie reece
  • 1167 Answers

SOURCE: 82 Suzuki GS650 Engine turns over but gets no fire to start.

take the plugs out and see if you have a spark get back to me

Posted on Sep 22, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2004 triumph Daytona 600.... will not start all it does when you push the start button is click. Have checked all 4 relays under seat and all grounds. Battery shows 12.2 volts and 166 cranking amps. Please...


If you check that is not an electric problem, and is not the batery, the problem should be from the starting motor. Try to start the bike by selecting the 2nd gear and pull, take a ride, till the bike is heat and try again to start the bike with the button, if the problem persists then you should change the starting motor. Before you change the starting motor, change the starting relay, is cheap and probably can solve your problem too.

Mar 05, 2015 | 2004 Triumph Daytona 600

1 Answer

Daytona 650 turns over but won't start


Hi, Chad and the usual suspects are:
1. Fuel tank empty.
2. The fuel tank has old dead gas.
3. Fuel tank bottom contaminated with ethanol sludge, dirt, water, rust, etc.
4. Fuel supply valve/petcock turned off.
5. Fouled spark plugs.
6. Engine flooded as a result of overuse of the enrichner.
7. Vacuum hose to the fuel supply valve/petcock disconnected, broken, cracked, or pinched.
8. Fuel valve/petcock or filter clogged.
9. Fuel line to carburetor or throttle body pinched, kinked or blocked.
10. Carburetor float stuck.
11. Fuel injectors clogged.
12. Fuel injectors stuck open.
13. Severely discharged or a damaged battery should have 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a cursory reading of 12.5 volts or more but little or zero amperage the battery is faulty and must be replaced, AGM batteries fail in this scenario more so than lead acid batteries.
14. Check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
15. Loose or corroded wire connection at the coil or plug between ignition sensor and ECM module.
16. Spark plug cables in bad condition and shorting check for spark leakage in the dark, cable connections loose, or connected to the wrong cylinders.
17. Ignition timing incorrect due to a faulty ignition coil, ignition module or MAP, CMP, CKP, O2, TPS, ETP, IAC sensors.
18. Faulty neutral, clutch lever, or kickstand safety switch.
19. Faulty fuel pump or fuse or relay.
20. A stuck bent or burnt valve.
21. Tilt sensor needs a reset.
22. Security system not disarming alarm needs a reset.
23. Check for engine trouble codes.
For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
Daytona 650 turns but wont start
What to do When Your Motorcycle Won Start
Triumph DAYTONA 650 Manual
Triumph 2003 Daytona 600 Service Manual
Triumph DAYTONA 650 Manual
http://www.bikebandit.com/oem-parts/2004-triumph-daytona-600-650/o/m17609

Jun 01, 2017 | 2005 Triumph Daytona 650

1 Answer

I own a triumph 2005 daytona 650.could anyone tell me if the engine light,flashing oil display and oil light being apparent, is normal when turning the key,not actually starting it


Not sure about the 650, but on my 04 Daytona 600, is does the same thing, this is the engine check lights, and oil low lights being checked. IF you tried to start the bike it wouldnt, until this sefl test is complete.

Hope this helps.

Jul 31, 2011 | 2005 Triumph Daytona 650

1 Answer

Symptoms - On start up: Takes a lot of turns on the starter to start, then runs below idle for a few seconds before getting to idle. Lately the starter motor is delayed after pushing starter switch,...


Hi, John_robe415 sounds like a wiring issue to me the first thing I would do is invest a little Drachma in a connector cable that goes from the ECM to your laptop under $12 or 10 quid that covers your make, model, year and retrieve any error codes that have been generated by your ECM for this scenario you will need your service/owners manual if you can't find the first and best tool you ever bought for your Triumph, despair not, for a mere zero $ you can download another one. For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
http://www.triumph675.net/forum/archive/index.php/t-29347.html
How to find fault codes on triumph motorcycle
Triumph 2003 Daytona 600 Service Manual
Purchase Triumph daytona 600 650 motorcycle parts online
Triumph Daytona 600 Owner Handbook Manual

Mar 01, 2017 | 2004 Triumph Daytona 600

1 Answer

2004 Triumph daytona 955i. 4000 miles. Was riding and all of a sudden bike dies, no power to lights speedo or any gauges, starter button wouldnt work. Pushed home and turned key on all lights worked and...


Hi, The_redneckc and the usual suspects are:
1. Severely discharged or a damaged battery should have 12.5 volts or better and be able to pass a proper "LOAD" test if necessary your battery may show 12.5 volts or more but have little or zero amps and must be replaced.
2. Failed alternator/generator and or voltage regulator.
3. Loose or corroded battery terminals and or cables especially the "NEGATIVE" cable, look for loose, corroded, or broken connectors inside the cable harness at "BOTH" ends.
4. Failed main circuit breaker or ignition switch, check for loose connections and continuity.
5. Failed system and or ignition relay, check for continuity.
6. Failed ignition coil, ignition/electronic module.
7. Failed CKP, CPS, CMP, MAP, TPS, or BAS sensor, corroded, loose or broken wire connector pins/sockets.
8. Throttle cables and or idle speed improperly adjusted hot idle speed should be 950 RPM to 1000 RPM.
9. Fuel tank empty.
10. Fuel tank contaminated with ethanol sludge.
11. Water or dirt in the fuel system, or clogged filter.
12. Restricted, blocked or kinked fuel line.
13. Faulty fuel pump.
14. Faulty pressure regulator.
15. Faulty or clogged fuel injectors.
For more information about your issue and valuable "FREE" downloads that you need please click on the blue links below. Good luck and have a wonderful day.
2002 955i Daytona Quits while running and then will not start
Topic Starting Issue on 2005 Triumph Daytona 955I RUNNING AGAIN Read 8197...
Triumph Daytona 955i 2002 Service Manual
Hermys Triumph Motorcycle Parts 2004 Triumph Genuine Body and frame...
Triumph Daytona 955i Handbook

Apr 17, 2017 | 2004 Triumph Daytona 955i

1 Answer

I just started my 2006 suzuki gsxr 600 for the first time since fall and it starts fine in neutral but as soon as i put it in gear it cuts off. The kickstand is up


Sounds like your clutch is stuck on [not disengaging when you pull the leaver]This can happen over a long storage-no use period.To fix put the bike in 3rd gear and start the engine with the clutch lever pressed[caution the bike will want to surge forward so keep your foot on the brake]Make shure to have the engine up to normal running temperature before you try this fix.the engine firing along with the brake pulled will release the sticking clutch plates.This will work!!!

Mar 08, 2010 | 2006 Suzuki GSX-R 600

1 Answer

Where can I find an exploded diagram of the rear spindle of my daytona 600, to show me what spacers go where. After having a rear tyre replaced, I now have a knocking sound, but only when using throttle,...


If it goes away when you pull the clutch in then I would think it something to do with the engine but i could be wrong there. Can you put the bike on a jack and put it in gear and maybe find out what going on. Let me know what you find out. You got me wondering.

Oct 03, 2009 | 2003 Triumph Daytona 600

1 Answer

Clutch slips


Hello, wheelies mm not good for your gearbox or clutch, 1st off is the gearbox working OK, does it jump out of 2nd gear under hard acceleration? then we can move on from this point,
Ian

May 26, 2009 | 2004 Triumph Daytona 600

2 Answers

Suzuki 600 bandit won't start


It could be the starter, or it could also be the starter switch or more over have you first checked tht engine 'kill' switch? If its on 'off' (Kill) position the starter won't operate from the button!

Other way is to short circuit the starter throught the solenoid switch and see if it works.If it does work thn the switch (button) is faulty you may hve toreplace it or sometimes a good cleaning can revive it due to carbon deposits at the contact points.
Thirdly, I hope the battery is at its top performance too!
Hope this helps.

May 11, 2009 | 1997 Suzuki GSF 600 S Bandit

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Triumph Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Triumph Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...