Question about Honda CB 900 Hornet Motorcycles

1 Answer

I installed a wolo air horn 419 and when I push the horn button all I here is the compressor and no horn.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 44 Answers

It is possible that you may have reversed the polarity on the compressor; it may be "pulling" air instead of blowing it out. Remove the air hose from the compressor and put your thumb over the air outlet while pressing on the horn switch. If you don't feel air blowing out, reverse the positive & negative wires going into the compressor and repeat the test. The air horns should work at this time.

Note: Always install a relay on this type of horn system; the compressor puts a high amount of load on the horn switch if you don't.

Posted on Apr 09, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you remove the horn


Hi, Michael first check for continuity at the power and ground wire at the horn, then check for continuity at the horn button, back in the day there was a small adjustment screw on the back of the horn, by turning it one way or the other you could set the limit on how much the diaphragm vibrated. For more information about your issue, please visit the websites below, and for specific information or questions, please feel free to contact me at xlch@mail.com. Good luck and have nice a day. Mini Beast Air Horn Installation
Wolo Bad Boy Air Horn Installation
Harley Davidson Manuals Mark Workshop
http://www.stcharlesharleydavidson.com/OEMpartfinder.htm
Owner Manuals Harley Davidson USA

Jan 06, 2016 | 2008 Harley Davidson FLHTCU Ultra Classic...

1 Answer

How do i install wolo horn on jeep with two factory horns?


If you are trying to make it work simultaneously with stock horns, I suggest you wire it in through a relay. Without a relay you will be placing too much of a load on the horn circuit.
A relay is typically used to control a component that draws high amperage. The relay allows full power to the component without needing a switch that can carry the amps. The switch only controls the relay. The relay then provides a direct connection to the battery. It should be noted that either the power(86) or ground(85) in the relay control circuit can be switched. In the case of a horn, the horn button would be used to switch the ground lead(85) and power(86) would be provided directly from the fuse box.
This is a typical wiring diagram for a standard relay installed for headlights, horn, fuel pump, electric fan, etc. If the relay has a 5th terminal, it is not used.

1e3e163f-0aca-4ffa-b9cf-593bcea94cd7.jpg

Aug 30, 2014 | Wolo Wolo Manufacturing BADBOY419 Model...

1 Answer

Horn doesnt work


Check power to the unit and power coming out of it. The pumps go bad on the horn like that a lot.If you have access to an air compressor then run air through the line to the horn portion and see if it works. If it does then more than likely it's the compressor unit being bad.

Dec 12, 2013 | Wolo Bad Boy Chromed Air Horn

1 Answer

Instructions for 2 terminal electric car horn


If you are by passing your original horn, disconnect the terminals going to it and place the new horn's wires in the horn terminal area. If the wires are color coded, red is for 12V black is for ground. It works when you close the circiot by pushing the horn.

If you are adding it, find your horn wires and splice into them. Each horn would operate seperately when it is pushed, the circuit is closed.

Last arrangement, find your horn wires on the original horn, hook wires from that horn and spilice the new horn wires into the one you want to add. do not connect it to the twelve volt When you push on your horn it will close the circuit for both horns to go off,

Dec 17, 2011 | Wolo Model 370 Black Metal Extra Loud Beep...

2 Answers

Horn does not work; where is the horn?? in a 2002 2500HD 4X4? Many thanks.\r\nBob ibGorham Maine


There's two of them located just above the parking light in front of each of the fender wells. You will be able to see them from the bottom looking up

Jun 26, 2011 | 2002 Chevrolet Silverado 2500HD

1 Answer

How to install wolo air horn #519 2004 ultra


Hi Benjamin, for more information about your question please visit the websites below. Good luck and have nice day.
Wolo Bad Boy Air Horn Installation

Jun 22, 2011 | 2004 Harley Davidson FLHTCUI Electra Glide...

1 Answer

How to install a wolo air horn #519 on 2004 harley ultra


Hi Benjamin, please be aware that this question has already been asked and answered. Thank you.

Jun 22, 2011 | 2004 Harley Davidson FLHTCUI Electra Glide...

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

277 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

75822 Answers

Mike

Level 3 Expert

4336 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...