Question about 1970 Triumph T 100 R

1 Answer

How do i stop throttle reving when i turn handle bars tried rerouting cable fixing outer cable nothing works

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Renaissance:

    An user who is expert in 3 categories / brands.

  • Triumph Master
  • 1,554 Answers

The only reason this would happen is the cables are being pulled somehow.

Either you missed something with the reroutung, and need to try again, or the cables are adjusted too tight, or the cables are too short.

Posted on Dec 15, 2012

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

flh1
  • 36 Answers

SOURCE: installing handlegrips

Not sure on the Harley but on dirt bikes and atvs I blow air in the ends and they come right off.Go on the same way.

Posted on Dec 25, 2008

Mitchy123
  • 216 Answers

SOURCE: replace handle bars on a 2006 HarleyDavidson RoadKing

I added a 2 inch riser to my dyna and didnt have to replace any cables, so - to answer your question, not always. There is plenty of wiggle room, however, if there is gonna be more difference that about 2 inches, replacement will be required. ADJUSTMENT WILL DEFINITELY be needed. And no, its not difficult, when u have the bars off, its nearly 1/2 done anyway

Posted on Mar 16, 2009

  • 9 Answers

SOURCE: how does the throttle slider sit in the throttle housing on a crf

It can only go in one way try a few veriations to get it, youl see,

Posted on Mar 31, 2009

  • 1 Answer

SOURCE: suzuki is reving high for a long time and loss of power

replace your stator side crank case seal

Posted on Jul 26, 2009

  • 850 Answers

SOURCE: 1990 vulcan 750 throttle

no spring in the grip!
id suspect the cables are binding up inside so disconnect at the carby end then & see if they are moving freely
Cheers Rob

Posted on Aug 16, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace throttle cable on the handle bar end


from my old motorcycling days. Unscrew the two screws that hold the fat end of the throttle, and when they split you will see a ball or small cylinder attached to the wire. Slip this out and either rethread a new and lubricated inner cable or pull the cable outer from the socket under the throttle and replace both. I would advise against using the screw down nipple connector as shown in the thumbnail image as they always pull out in time. Good to keep one in your riding jacket though for a quick roadside fix..

http://www.doityourself.com/stry/how-to-replace-the-throttle-cable-on-a-motorcycle


Lots of videos.
replace motorcycle throttle cable Bing Videos

Sep 29, 2015 | Motorcycles

1 Answer

Hi rpms when starting and staying hi while riding


try rerouting the throttle cable, could be making it jam up if it has a tight bend, if not this, then check your inside throttle cable, sounds like it might have a couple of broken wires and they are jamming inside the outer cable, or the outer cable could be bent.

Mar 23, 2014 | 2002 Suzuki GSF 1200 Bandit S

1 Answer

High idle how do I adjust the idle down?


http://www.bikebandit.com/1994-suzuki-vs1400glp-carburetor-rear/o/m139273sch259338

This is the REAR carb.

Item #42 is the idle speed adjuster.

When the engine revs just by turning the handlebars this is the routing of the throttle cables hanging up, and pulling on the cables when you turn the bars....reroute cables!

Dec 16, 2013 | Suzuki VS 1400 Intruder Motorcycles

2 Answers

2001 yamaha ttr 125 when started it runs at full throttle without me touching the throttle


I would check the throttle adjustment screw on the throttle assembly on handle bars. Be sure it is not screwed all the way in for max throttle. You can also check the carb and be sure that the idle screw is not adjusted for high idle as well. There may be an adjustment screw on carb for the cable stop.

Nov 22, 2013 | Motorcycles

1 Answer

Need to find out how to fix the throttle! I push the throttle in but it won't swing back into place! My 10yr old is putting the motor into a scooter!


To make a throttle cable or any cable you have to have both ends fixed to the same bar. IT cutter shaft mount bar mower handles etc otherwise the inner won't move as when you push the throttle the outer moves and not the inner.. By you video you need to fix this first.

Mar 03, 2013 | Garden

1 Answer

Motorcycle revs up when handle bars are turned


What kind of motorcycle is it? does it use 2 cables? if so, the idle cable is probably too tight. there should be an 1/8 in free play when bars are straight. the throttle should snap back after u turn it wide open and let go in all positions.

Mar 08, 2012 | Motorcycles

1 Answer

Egine reves up when turning handle bars 1981 650 yamaha


Re route the throttle cable if ness, is the twistgrip tight to turn, do you have any free play at the cable? You may try turning the addjustment back on the throttle pull cable on the twistgrip

May 01, 2011 | Yamaha XJ 650 Motorcycles

1 Answer

I need a diagram for the throttle connection to the trigger in handle of a poulan pp3516avx chain saw


Sorry there are no diagrams of how it fits, there is a parts list that shows the cable, as far as i remember the end of the inner cable has a dog leg in it, that hooks into the trigger, and the outer cable is secured in the right hand handle half, once the other half is assembled it stops it from popping out, the other end also has a dog leg this hooks into the throttle spindle, and the outer is secured in the air filter houseing.

Feb 28, 2011 | Poulan Garden

1 Answer

1995 xjr400 throttle sticks open and will slowly close on its own if allowed. already loosened bar end and replaced grips but not any better. any ideas?


they can stick in a number of places.
You may need to dissassemble the hand throttle assembly
Make sure the plastic twist grip turns freely on the handle bar.
Check the new grip doesnt push against the throttle switch assembly.
Check the cables move freely
Check the cables dont have any frayed ends
check the cables arnt missing any of the plastic outer cover
check the cables a routed correctly and dont get jammed or pulled turning lock to lock

Aug 10, 2010 | 1998 Yamaha XJR 400

1 Answer

Engine Scooter, throttle does not work


trace the cable to the connection on the motor.check that throttle lever is connected to cable,and lever moves when throttle is turned.cable may have broken.

Oct 06, 2009 | 2008 Yamaha Yamaha G5

Not finding what you are looking for?
1970 Triumph T 100 R Logo

Related Topics:

68 people viewed this question

Ask a Question

Usually answered in minutes!

Top Triumph Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Triumph Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...