Question about 2006 Harley Davidson XL 883C Sportster Custom

1 Answer

My right side foot peg shaft is loose. How do I tighten it?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    New Friend:

    An expert that has 1 follower.

  • Expert
  • 98 Answers

If you are talking about the front foot peg. Take the screw that holds the peg to the mount out. Inside the mount you will see an allen that tightens the mount to the shaft you will need to tighten this allen. Then put the peg back on and your done.

Posted on Apr 06, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Bar that hold the sewing foot is loose


If the comment already posted did not answer your question, here is another thing to check. If the screw that attaches the foot and ankle to the presser foot bar is tight, and the foot can still be moved, it is likely that the presser foot bar has become loose within the lifting mechanism. You could save yourself some trouble by taking your machine to a sewing machine repair shop, but if you would rather avoid that expense, do the following. Remove the needle bar and take up mechanism cover on the left side of the machine. This is held on by a single phillips head screw on the back side of the machine, which, with the back of the machine facing you, should be on the top right side of the machine. Once this cover is removed you will be able to see two vertical metal shafts, one is attached to your needle clamp and needle, and should be in the front. The other is the presser foot bar, and will be behind the needle bar. There should be a small allen screw about halfway up that shaft that tightens onto the bar. With the presser foot properly positioned on the needle plate, tighten this allen screw. Don't tighten the screw too tightly, as this can damage the presser bar, just make sure it's nice and snug. Make sure the presser foot raises and lowers properly, and re-attach the needle bar cover.
Hope this helps.

Mar 16, 2014 | Brother CS6000i Computerized Sewing...

1 Answer

I've tightened all the screws on my Kuryakyn


get a shorter shoulder bolt that allows it to tighten up. Be sure to get a new nut. Allow the difference to not tighten it up so much as to "seize" the foot peg so as not to fold up as the manufacture engineered it to.

Jun 04, 2013 | Motorsports

1 Answer

Foot peg on brake side of my '96 sportster is loose how do I tighten it


Hi Anonymous, take a ride over to your local dealers service department I'm sure they will be happy to offer advice and assistance concerning your issue. Have a nice day

Apr 22, 2013 | Harley Davidson XL 1200 C Sportster Custom...

1 Answer

Guitar tuning peg seems like it might be broken it will tighten the string to a certain point then it clicks and its completely loose again...I'm new to guitar so I don't know If this is normal


It seems like you wound and tightened your string on the tuning peg loosley. Try wounding the string at least 4-5 times around the peg after you pass the wire though it and then after winding pass it through the hole again. Tighten well.
If that doesn't work your peg might be broken, but looking at it on the video seems that it's not, even though you can't see it clearly.
Try tightening the screws on the peg, since there's a lot of tension on the highest string and it might cause the peg to click back because the tension is too high and it's loose.

Jan 30, 2013 | Music

1 Answer

Can't tighten left front foot peg mount on 2000XL


on the end of the peg you will see a head for the bolt it requires an Allen wrench to tighten.

Dec 29, 2012 | 2005 Harley Davidson XL 1200 C Sportster...

1 Answer

Trying to get right side foot peg case off foot peg seems to have a nut behind case not sure how to get off


Yes there is a nut on the backside of the stud that the peg mounts to. The stud is also the shaft for the rear brake pedal. To get to the nut, take the master cylinder loose and the snap ring that holds the rear brake pedal on or the remove the pin from the brake pedal. Now, take the large nut below the peg and brake pedal shaft off and the other two bolts that hold the front sprocket cover on. Remove the cover and you can get to the nut.

Good Luck
Steve

Apr 03, 2011 | 1993 Harley Davidson XLH Sportster 883

1 Answer

How to change the shifter foot peg on my 2001 harley roadking classic


Remove pinch bolt from shifter. Remove shifter from shaft. You may need to spread shifter with wedge (screwdriver) to get it to slide off. Put on new shifter and tighten bolt to secure.
A little blue locktight will keep it from falling off.

Feb 07, 2011 | 2001 Harley Davidson FLHR - FLHRCI Road...

1 Answer

My right foot peg shaft of loose, how do I tighten


Hi Anonymous, you have to remove the three sproket cover bolts/screws then remove the sproket cover to gain access to the footpeg support shaft nut. Good luck.

May 13, 2010 | 2001 Harley Davidson XL 1200 C Sportster...

1 Answer

My right foot peg shaft is loose, how do I tighten it?


Hi Stearman7b3, you have to remove the rear brake master cylinder then the sprocket cover to gain access to the foot peg shaft nut. Good luck and have a nice day.

Mar 21, 2010 | Harley Davidson Motorcycles

1 Answer

Foot peg bracket removel 2000 sportster


you must remove pulley cover and master cylinder. inside cover is a large nylock nut holding peg mount. once removed a bolt and nut should be replaced in its place as it holds some of master cylinder

Jan 25, 2009 | 2000 Harley Davidson XL 1200 C Sportster...

Not finding what you are looking for?
2006 Harley Davidson XL 883C Sportster Custom Logo

Related Topics:

534 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Gills Lango

Level 2 Expert

195 Answers

Mike

Level 3 Expert

4336 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...