Question about Suzuki RM 125 Motorcycles

1 Answer

I have a 1994 Rm 125....Does the bike have to be running to see if the clutch works

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 9 Answers

No, put it in gear, pull in the clutch and push it. It may drag at first but then it should break loose and roll with little friction. You should also be able to kick it in gear with the clutch held in. This will tell you if it disengages but not if it will hold under heat and hard acceleration. So I guess the answer really is that you can check half of what a clutch should do. Good luck.

Posted on Apr 06, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2000 Suzuki rm 125, when in gear with the clutch pulled in the bike is always in gear and I can't stop with out stalling i have tried all adjustments on the cable. Any advice


Are you using the correct 10W40W wet clutch motorcycle oil? It has special friction modifiers in it for this clutch drag issue.

Nov 19, 2012 | 2003 Suzuki RM 125

1 Answer

Dirt bike will not run idle


sounds like a side stand switch problem , but its in an RM listing,

Apr 24, 2010 | 2003 Suzuki RM 125

1 Answer

2000 suzuki rm 125 have done a complete rebuild on bike new cables new clutch new top end every thing new even down to a complete new bolt kit i used to race and know these bikes in and out but i am...


look for grooves or dents in the clutch basket, that would be holding the disks apart, also make sure the disks all face the same way out.

Mar 16, 2010 | 2003 Suzuki RM 125

1 Answer

2001 rm 125 transmisson oil level


It does have a small bolt on the clutch cover, with the bike standing straight up, fill it untill the fluid runs out of this hole.

Aug 18, 2009 | Suzuki RM 125 Motorcycles

1 Answer

91 SUZUKI RM 125 CLUTCH PROBLEM


First, try the cable adjustment at the lever end, if no more movement re-adjust inwards, then adjust at the clutch end.
If no joy, then it is either the lifter mechanism or the clutch its self.
Ride Safe
Bike-Doc

Please mark this as useful (if it has been!!)

Aug 03, 2009 | 2003 Suzuki RM 125

2 Answers

Clutch not working


What type oil in your crankcase? Wet clutches go on strike with wrong oil. Engine oil is a no no.

Jul 10, 2009 | 2003 Suzuki RM 250

2 Answers

Clutch rm 125


Okay, this may take a couple of comments back and forth but I can get you back on the road. First, Have you done any work on the clutch lately? If so, what and why? Did the clutch work okay after the work? Have you changed gearbox oil in the last month or so? If so, EXACTLY what oil did you put in the gearbox? i.e. "10w40 Mobil Super Blue fluid with silicone friction limiters". Just post a comment to get back to me.

Jun 20, 2009 | 2003 Suzuki RM 125

1 Answer

I have a suzuki rm 125 1994 model when i pull the clutch lever in to put it in gear the clutch doesnt work t jst crunches into gear


Adjust the clutch cable to allow about 1/4" free play at the end of the clutch handle. Don't put the bike in gear until the rpms are near idle speed. The clutch is working fine if the bike does not lurch forward when going into gear at idle speed. Dirty, gritty oil in the gearbox can make the clutch grab. Consider changing oil if grabbing is the problem. The "crunch" you hear is the slider gear engaging into the driven gear. The higher the engine speed when being put into gear the louder the crunch. The slider gear engaging "dogs" can break. Crunching into gear is hard on the gears.

Post a comment to let me know how you come out on this.

Jun 04, 2009 | 2003 Suzuki RM 125

1 Answer

Bogging issues and clutch adjustment on 1980 RM 125


As far as your clutch adjustment ,I can't help you but the fact that the bike is older you might want to try removing the exhaust pipe at the baffel end and see if there is a difference in power ,if there is clean out your baffel and your good to go. hope this helps
jerry

Apr 12, 2009 | 2004 Yamaha V Star Classic

1 Answer

Clutch specs.


i just replace my clutch in my 04 rm125 tonite.i rode my bike with clutch going for about 4 months.last week locked up iv learn if it locks up stop .change clutch and spring asap.to answer your question if your having problems ....EBAY EBAY brought new clutch and springs for $42 with shipping ...... the best part shipped in 2 days

Mar 10, 2009 | 2003 Suzuki RM 125

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

145 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers

Richard
Richard

Level 2 Expert

83 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...