Question about kawasaki ZX-7R Motorcycles

1 Answer

My kawasaki zx7s750 is sluggish slow weak just had carbs cleaned

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert who has achieved Level 3.

  • Master
  • 403 Answers

Does it idle ok ? were the jets removed and cleaned ? is your plug gap correct ? check on those and get back to me.

Posted on Apr 01, 2011


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

What is wrong wIth my Honda xr 125 idle?

have carb cleaned ethenol kills carbs

Mar 22, 2015 | 2005 Honda XR 125 L

1 Answer

Kawasaki KX65 will not start. Help?

Does it start with starting fluid? Have you checked the reed valves?

Aug 03, 2014 | Galfer Kawasaki kx65 kx 65 2002-2004 front...

1 Answer

My 1998 Kawasaki jet ski is sluggish on take /

Probably need a fuel system clean out and or a new carb. Also check engine compression and make sure it is at minimum psi. The reed vales between carb and engine may worn out. To be honest, since its so old it is probably time to consider replacing it or rebuilding the engine if hull is in good shape. You may not be able to even get the parts for it.

Jun 29, 2014 | Garden

1 Answer

Starts ok, although seems to be missing slightly, sluggish throttle response and wont rev beyond 4 thou ,

Check plugs, may be fouled> When storing bikes in my old mans garage, the plugs always foul

Mar 29, 2013 | 1995 kawasaki GPZ 1100

1 Answer

I have a 2000 kawasaki zx6r. i layed it down at about 50 and put new plastics on a took off carbs and cleaned them because of throttle stick well when i put them back on i synced the carbs and it revs...

You might still have clogged pilot jets, also check the cold start circuit and idle circuits, when you synce the carbs did you do them at idle and 6k rpm?

Jun 09, 2011 | kawasaki ZX-6R Motorcycles

1 Answer

Have 24 hp kaw. engine on Cub lawn mower. At idle, engine is erratic, revs, then slows, revs, then slows.

Hello. The usual cause of carb "hunting", is a weak governer spring. Although it might look fine it may not be and I would replace it. Another possible cause is a float problem. Finally it could also be the fuel filter or a chunk of debris in the carburator.

Jun 08, 2010 | kawasaki Fh680vgs24 23hp 23 Hp Lawn Mower...

1 Answer

Jerking like fuel cut off when slow down

You might try to sync the carbs and adjust the pilots but sounds like you are due for a carb cleaning.
Ride Safely, Ed

Apr 09, 2010 | 2001 kawasaki VN 800 Vulcan Classic

1 Answer

Have a 97 Suzuki GSXR750 that is sluggish in first till about 30mph then gets up and goes. any Ideas as to why?

It is a carb(s) problem in that the low speed side of the carbs is blocked by debris or varnished frpm bad gas. Pull the carbs, clean them and you will be back in business! The process of pulling the carbs is a bit detailed for this forum, so I suggest getting a manual from your local library and follow the carb removal instructions. it isnt that difficult and can be done in a couple of hours. Be sure to use a good carb cleaner (such as STP from the auto parts store) best wishes!

May 09, 2009 | 1977 kawasaki Z 650

2 Answers

Carb on 2005 kawasaki Bayou 250

remover all plastic/ rubber parts
then soak the whole carb body and slow jet in lacquer thinner

the slow speed jet/needle circuit needs to be cleaned with just 1 strand from 18 gauge copper wire going through all passages an holes pilot circuit in pic2989f1c.jpg

Apr 01, 2009 | 2005 kawasaki KLR 250

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

49 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers


Level 3 Expert

76682 Answers


Level 2 Expert

342 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides