Question about 2002 Honda CR 125 R

1 Answer

I have 1982 cr 125, I'm having a hard time starting it I cleaned the carbs changed the filter put new oil in it but it won't start.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Renaissance:

    An user who is expert in 3 categories / brands.

  • Honda Master
  • 1,190 Answers

Does it have a spark ? remove plug , place in hand and crank , do you feel it tingle ? if not check cap is ok , remove it and put ht in hand and crank , any joy ? if not then check coil etc ! P...

Posted on Dec 25, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 2336 Answers

SOURCE: keihen carb

Honda or husquy cr 125

Posted on Nov 10, 2008

robotek
  • 1512 Answers

SOURCE: oil

Hi KK
Use 600 ml is you are changing the oil, or 650ml  if you have just rebuilt the engine and filling from dry. Use light weight gear oil. 
regards robotek

Posted on Dec 20, 2008

  • 74 Answers

SOURCE: oil change

On the right side of the crankcase there is a little see through glass, fill the oil until the you can see the oil in the middle. you must have the bike in a straight up and down posistion.

Posted on Dec 21, 2008

ollie reece
  • 1167 Answers

SOURCE: how much oil should i put in my drz 125 after oil

1.2L OR LOOK AT SIGHT GLASS ON NUMBER 3 PIC BELOW bf99263.jpg

Posted on Oct 10, 2009

  • 3567 Answers

SOURCE: suzuki gn 125 lacking power

I assume you dumped out the half pint of old gas and rinsed out the tank. Get a new spark plug and clean the air filter. Remove the carb and dis-assemble it then soak the parts in denatured alcohol for 30 minutes. Do not soak the rubber diaphragm. Finish the cleaning with a can of spray carb cleaner from the auto parts store. Be sure all internal fuel and air circuits are clear and that the diaphragm is not torn or has pin holes. The top cap must have a good seal. Go to www.babbittsonline.com/parts/viewbybrand/parts.aspx to see a diagram of the carb and the rest of the bike. It looks like they have lots of parts for your bike.

Posted on Feb 10, 2010

Testimonial: "GREAT HELP THANKS"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My Honda 2002 cr 80 wont idel and is hard to start. I put a new carb kit and plug in it and still is hard to start.


The main cause of an idling AND starting problem is a clogged pilot jet--the small one. Take it out of the carb, blow it out again and make sure you can see light through its very small opening before reassembling the carb.

And, be sure the compression is 125 psi or higher.

Sep 26, 2014 | 2005 Honda RC 51

1 Answer

Aprilia rs 125 won't start!!


right you done quite a bit, so whats left, fuel seems ok .. so ht lead ht cap, spark plugs dont always come with right gap, any leaks with airflow either side of carb, remember the filter often acts as a restrictor too. try the putting a small amount of fuel in cyclinder after cleaning plug, should atleast get a backfire, is choke setup ok, carb mix if not factory sealed is generally 1 and 3/4 turns out from tight,

Feb 13, 2013 | 2005 Aprilia RS 125

1 Answer

2007 TTR Yamaha won't start


you will probably need to clean the carb there is a you tube video on how to remove and clean

Jun 09, 2012 | Yamaha TT-R 125 L Motorcycles

1 Answer

I just got a 1994 yz 125 and when i was riding it ,.. it would run good as long as i was going slow and not raping out the gears .. but when i would give it a lot of gas to take off it would bog out and...


if the plug is sooty your float is set wrong the air filter should have oil on it to catch dirt.sounds like a carb problem although it could be the power valve

Aug 24, 2011 | 2003 Yamaha YZ 125

1 Answer

Hi I got a 98 yz 250 new clutch plates piston negosiled barrel new ring and shortcut the gears I kicked it and it started on the 3 rd try I ha then added more fuel and mixed 200 ml oil to 5 liters petrol...


Replace the spark plug to new one they rarely come good or be reliable once fouled shouldn't need to clean carb but if were mine I would clean it anyway
regards Jamie

Aug 04, 2011 | 2008 Yamaha yZ250

1 Answer

I put new gas, oil and spark plug and cleaned out filters and carb but it still wont run??


do you have a spark ? plug out , put ht on and place on head and crank ! or the qwik test is hold plug in hand and crank ( slowly ) and you should feel small voltage !! honestly !!

May 28, 2011 | 2003 Honda CR 125 R

1 Answer

Have a honda crf100f 4cycle got spark wont start,


CLEAN THE CARB AGAIN IF IT RUNS ON STARTING FLUID ITS NOT GETTING FUEL YOU WILL NEED TO REMOVE THE JETS AND MAKE SURE THEY ARE CLEAR

Jan 23, 2010 | 2002 Honda CR 125 R

1 Answer

Steven


Remove the water trap bowl at the bottom of the petcock, (gas valve). Any water or trash in the bowl? Drain a cup of gas from the tank. Any water or trash in the cup? Dump it, clean it and re-mount it, ( not all bikes have a water trap bowl ).

Drain the carburetor. There should be a screw on the lower side of the carb float bowl. Remove the screw then replace it after the fuel drains. Turn the gas back on and wait a minute for the carb to fill with gas. Install a new stock NGK spark plug and try to start the engine. If the bike doesn't start and run properly then shut off the gas and remove the carburetor from the engine.

Remove the float bowl and clean the entire carb with a spray carb cleaner from the auto parts store. Wear protective goggles to avoid getting spray in your eyes. Spray into all the little airways and fittings in the carb. Remove the two screws on the outside throat of the carb and spray into the screw holes as well.
< < READ CLOSELY > >
Be sure to put these two screws back in the same hole they came out of. IMPORTANT > do not tighten these two screws down. Only screw these in until they LIGHTLY seat. Now turn each screw one and one half turns outward. Put the rest of the carb back together, clean the air filter and install the carb. Let the float bowl fill then start the engine. Set the idle speed with the idle screw. This process should get you back on the road.


Please rate this solution. Thanks!

Apr 01, 2009 | 2005 Honda CR 125 R

Not finding what you are looking for?
2002 Honda CR 125 R Logo

Related Topics:

154 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers

yadayada
yadayada

Level 3 Expert

76848 Answers

bazzz7071
bazzz7071

Level 2 Expert

342 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...