Question about 2002 kawasaki KLX 300 R

1 Answer

How do you ajust the over head cam chain - 2002 kawasaki KLX 300 R

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 3,567 Answers

Just loosen the tensioner bolt then re-tighten. The tensioner assembly is on the back of the cylinder. Please rate my answer. Thanks! how do you ajust the - tombones49_22.gif

Posted on Mar 27, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2002 suzuki xl-7 Head Removal: Do I need to take the front timing chain cover off in order to take the head off? I don't have a manual yet. Resources hard to get for this vehicle...


the timing chains have to come off , they hold the cams down in the head bearings , so yes id say u have to remove chain cover off to be able to remove the cams !!

(and yes I know theres a bolt on ends of cams )

Oct 20, 2016 | 2002 Suzuki XL-7

1 Answer

Adjust timing chain


Well first u need to remove the top cover and get to the cam. Remove the two bolts holding the cam sprocket and turn the engine till its at the tdc mark on the alternator rotor.on the sprocket there should be two notches. These have to line up with the top surface of the head. Ie one of the bolts is up one down. Put the head cover back on and ur timing is set. Then if it is anything like my xl250s on the back rhs of the head there should be two bolts. The one at the top is a 10 mm bolt the one at the bottom is a 10mm nut. These adjust the cam chain tension. Start the bike. Warm it up and while idleing loosen both off NO MORE than TWO turns. Tighten them back up and there is your chain tension done. If it slips u prob need a new cam chain.

Aug 05, 2013 | 1983 Honda XL 125 R

1 Answer

Excessive noise from camshaft after head reconditioning and correct adjustment both standard setting and allowing for head being shaved - to no effect on a daihatsu charade 1991 G100


if its upper noise eg folowers and lifters if they are hydrolic lifters where these replaced are the cams ok if they are manually ajustable tappets these can be ajusted unless the following are goosed again the cams are pitted or mishapen will need new cam shaft the lifter rods are worn or week valve springs
but if they are hydrolic will have to be replaced inc cam shaft hope this makes sence ivan

Oct 01, 2012 | 1990 Daihatsu Charade

1 Answer

How do i ajust the cam chain on a xj 900f


you don't, its self adjusting, if it feels slack you prob need a new chain or guides.

Sep 05, 2012 | Yamaha Hc1-1 Xj650 Xj700 Xj750 Xj900...

1 Answer

Suzuki gsx 750 f how to ajust cam chain


It can't be adjusted, it's self adjusting with a tentioner. If it makes too much noise, replace the chain and don't forget the guides and tensioner!

Jun 06, 2011 | 1989 Suzuki GSX 750 F (Katana)

1 Answer

Yamaha xt 200 cam chain needs needs ajusting can you help me out


Your XT has a self adjusting cam chain tensioner and needs no attention unless it has broken.

Sep 09, 2010 | Yamaha DT 125 X Motorcycles

1 Answer

Cam chain noise on a CBR1100 from 1998 Can this be ajust ? if so where is the bracket on the engine


Cam chain normally must be replaced, but sometimes cam chain tensioner may have some space to put more tension to tighten the cam chain. If you know how to access it then go for it. Good advise?

May 04, 2010 | 1998 Honda CBR 1100 XX Super blackbird

1 Answer

Id like to know how to ajust the cam chain on my


I don't know that exact model but all cam chain tensioners are automatic these days & have been for over 20 years

Hope this helps (if so please mark as helpful !!)
Ride safe
Bike-Doc

Apr 21, 2010 | 2004 Honda XR 125 L

3 Answers

It will not start and it backfire after valve adjustment. did i put the cams back the wrong way?


did u hav piston @tdc power stroke-valves shud slightly clic with ur hand after ajust-mite hav performed it at exhaust stroke! let me know

Jan 26, 2010 | 2002 Yamaha YZ 426 F

Not finding what you are looking for?
2002 kawasaki KLX 300 R Logo

Related Topics:

266 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4899 Answers

yadayada
yadayada

Level 3 Expert

79865 Answers

bazzz7071
bazzz7071

Level 2 Expert

342 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...