Question about 2000 Husqvarna TE 410

1 Answer

Hi have a Husqvarna 410 2000 got spark fuel back fires but wont start checked flywheel is on right valves rock at top dead centre ... ?? but wont start ? kick start only tho ?

Posted by on

  • 2 more comments 
  • vaughn51 Mar 28, 2011

    Ho there is spark but not sure how strong it should be ? plug always dry when we check it after trying to start it ! It does back fire when trying to kick start it . It has a delorto carb and not sure if this type have a slow speed circuit?

  • vaughn51 Mar 28, 2011

    It has got spark but not sure how strong it should be ? The plug is always dry after tring to start it but it back fire when trying to kick start it ! It has a delorto carb and not sure if it has a slow speed circuit ?

  • vaughn51 Mar 28, 2011

    well we tried that .. new plug , starting fluid but to no avail ... backfired but still not staring ...

  • douglas linebaugh Mar 25, 2012

    i have the same bike and the same problem it has good compression good spark it even jumps a 10mm gap i checked the timing every thing looks good still wont start. if you found a solution please hit me back or post a commentthanks

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 3,567 Answers

If the valves "rock" at TDC, the piston is at TDC EXHAUST, not TDC COMPRESSION. Chances are the engine is flooded. Install a fresh spark plug and go easy on twisting the throttle when starting the bike. Be sure the battery is in good condition. Push the kick lever to just past TDC compression then give a strong kick. Don't try to kick start with the piston going upward on the compression stroke. Be sure the air cleaner is not dirty and you have good gas. Please rate my answer. Thanks!

Posted on Mar 27, 2011

Testimonial: "great "

  • 5 more comments 
  • vaughn51 Mar 27, 2011

    ok will try .. gave it fresh gas cleaned tank and carb ... all perfect... but still nothing .... when we first got bike it was a non runner checked compression was very low ,,... so we un did valve lifter and there was loads of compression but we still couldnt start it ..

  • vaughn51 Mar 27, 2011

    is there anymore things to check please .. tried bumpstarting it but to no availe the back wheel locks up if not enough weight on the bike

  • tombones Mar 27, 2011

    When you bump start, have the bike in 3rd or 4th gear. That will lessen the wheel lock up. The valve being too tight makes me wonder if the prior owner did a top end job and didn't get the cam timing right. Check the plug, is there spark?

  • tombones Mar 28, 2011

    As mentioned before, install a fresh spark plug if you haven't already. Next, get a can of spray starting fluid and give a good shot into the air cleaner. Now try starting it.

  • vaughn51 Mar 28, 2011

    tried new plug ... and quick start but just back fired ... no start tried hard but to no avail ! ah well

  • tombones Mar 28, 2011

    The following web site says they have a free download of your bikes service manual.
    I suggest you do the download then look to see the photos of the cam gear relative to timing marks on the gear. If the cam is out of position the bike will never start. Since the valve was way off in it's setting, obviously a prior owner has been tinkering with the top end.
    http://www.manualedereparatie.info/en/do...

  • bradleybanks Apr 05, 2011

    Sounds just like what my TE410 did. On my bike it was the flywheel magnets came loose. I would kick and kick and every now and then it would back fire.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a Husqvarna HU 675 AWD 22 inch cut. It will not start, replaced the spark plug already. Need help


Hi Troy, the link below is a short YouTube video showing the right colour spark and it should spark over the top of the centre electrode...
How to check for Spark Plug Fire in any engine
If it doesn't spark then check the solinoid....
How to test lawn mower solenoid
shows all safety switches disabled....
Disable all lawnmower safety switches
But if it sparks then it's a fuel problem. You need to pull your carby off and unscrew the bottom half from the top, 1st sign of a needle stuck inside the seat is a dry carby There you'll find the float, push the float up and down and see if the needle above the float slides up and down from the seat, If the needle stays up then it's stuck and NOT letting the fuel into the carby, Just pull it down with your fingers to loosen it up..I hope this helps.... CHEERS..


Apr 24, 2016 | Husqvarna Garden

1 Answer

I have 03 kawasaki praire 650 v-twin its backfiring through front carb and wont run whats wrong


Backfiring through a carb is indicative of over advanced ignition. The spark is firing the fuel too early and exploding through the carburettor, instead of firing the piston over Top Dead Centre (TDC).

Another possibility is a damaged valve, do a compression test and get the timing checked.

Jan 02, 2016 | kawasaki Motorcycles

3 Answers

I bought a 1984 chevy 350 engine from a salvage yard that ran but never ran right. Come to find out it had a bad exhaust valve. we took the head off blew it out and replaced the valve and put the head back...


If you have a weak spark it will not start since under compression it takes a much stronger spark to jump the gap as compared to a spark in normal air pressure. Try a good known working coil.

Mar 29, 2017 | 1985 Chevrolet El Camino

1 Answer

I hit a rock motor died turnsover free wont fire


it is common after hitting a rock for the key to shear on the flywheel to crank remove the flywheel and check it

Sep 17, 2012 | Husqvarna 21" Lawn Mower with Honda GCV160...

1 Answer

Just rebuilt a husqvarna 372. New crank bearings, seals, all gaskets. Has good spark and gas. Why wont it fire?


If there is a good spark and there is good fuel at the plug the only reason it wont fire or do somthing is if the ignition timing is out, this can happen if the alloy flywheel key has sheard, remove the flywheel and check, unfortunatly if the key has gone it is a new flywheel.

Jan 25, 2011 | Husqvarna Garden

1 Answer

Did a top end job put it all back to gether and nothing. i went back checked timing,valve shims , fuel its getiing spark its gott compression but still wont run. Could that mean the cdi is bad?


Good spark? = CDI ok. Check the timing with a timng light. aim it down the inspection hole to see the "T" mark on the fly wheel. if it flashes, and you can't see the 'T' , then your timing is off. If so, check the flywheel position. At top dead center, a few things should be true. 1) your intake and exhasut valves are shut, with .006 clearance on intake, and .010 clearance on exhaust. 2) The "T" mark on the flywheel should be visible and aligned with the notch on the inspection hole. IF your timing is ok, and your spark is good then try spraying starting fluid into the carb. if it fires up when you spray, then you have fuel delivery issues. check float height and check bowl by opening drain screw a bit to see if fuel comes out. if no fuel, then examine float needle, tank petcock, and float height.

Jan 14, 2011 | 2004 kawasaki KX 250 F

1 Answer

OK i have a 1991 ford ranger 3.0 i have put the engine on top dead center (i believe) i put a paper towel in number one piston and when i turn the engine over it pushes it out i stop turning it over i...


just because the piston comes to the top does not mean its on compression stroke. the piston comes to the top on the exhaust stroke aswell !! if ur out by a single tooth it wont start. take of ther timing belt cover and the 'rocker cover'. ensure no 1 at top dead centre making sure valves 1 and 2 are 'rocking'. both valves must be shut(as in up not down) for a compression stroke !! refit ur distributor ensuring its perfectly on no 1. rebuild and bobs ur uncle. ps u may have choked out ur plugs starting up like u did, make sure they are clean. good luck.

Jun 17, 2010 | 1998 Ford Mustang

2 Answers

17.5 briggs intek backfiring thru carb wont start have adjusted valves?


Easy things to check, flywheel key, make sure it is not broken, check the coil gap to the flywheel. could be the coil is not advancing. Check, if it has one, the oil sensor by unplugging it. hope this helps.

Apr 14, 2010 | Parks Optical 13.5hp Briggs And Stratton...

1 Answer

My husqvarna 50rancher chainsaw wont start


Check your fuel make sure it is new fuel. Check to make sure that you have spark. Even replace the plug, for the price of 3dollars it is not a bad deal. If those do not work then you are going to have to check your flywheel and your armatur those are the items that would prevent you from firing since Huska makes a excellent carb you do not need to mess with it at all. Thank you for choosing FIXYA.COM please rate

Feb 14, 2009 | Husqvarna "Chain Saw - 16" Bar, 3 Hp

Not finding what you are looking for?
2000 Husqvarna TE 410 Logo

542 people viewed this question

Ask a Question

Usually answered in minutes!

Top Husqvarna Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

venugopal durairajan

Level 3 Expert

464 Answers

choprboz5

Level 2 Expert

196 Answers

Are you a Husqvarna Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...