Question about 2005 Triumph Speed triple

1 Answer

Hi i have oil going over my rear wheel could it be from the rear hub . if so what is the problem . cheers .

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,489 Answers

If the oil is leaking around the hub, the seal needs replacing. More info let me know.

Charlie

Posted on Mar 27, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Needto lubricate rear wheel bearings on a huffy single speed bike


as most bikes do not have seals on the wheel axles , it is possible to lay the bike on the side , use machine oil on the hub and axle area and spin the wheel while allowing drops of oil onto the axle bearing hub area
or you can take the hub apart and fill with a very light grease

Jul 23, 2015 | Huffy Cycling

1 Answer

Replacing rear hub/bearing assembly on 2003 taurus with drum brakes/abs


The wheel bearings in a Ford Taurus are located in the hub/bearing assembly. Replacing the hub/bearing assembly is a straightforward process -- remove the brakes, then the bearing, and reassemble.

Not enough space available for step by step instructions. Try this link:

http://www.ehow.com/how_5488471_change-wheel-bearing-ford-taurus.html



Cheers,

TF

Jun 02, 2011 | 2003 Ford Taurus

1 Answer

How do i pull the hub off my 2002 mazda , on drivers side front


REMOVAL & INSTALLATION Except Miata FRONT
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove or disconnect the following:
    • Steering knuckle from the vehicle
    • Inner oil seal from the knuckle
  3. Using Mazda Hub Puller tools 49 G033 102, 49 G033 104 and 49 G033 105, pull the front wheel hub from the knuckle assembly.
  4. Remove or disconnect the following:
    • Bearing inner race from the front wheel hub
    • Retaining ring from within the knuckle
    • Front wheel bearing from the knuckle, using the hub puller tools
    • Brake dust shield
  5. Clean and inspect all parts but do not wash or clean the wheel bearing. The bearing must be replaced. To install:
  6. Using Mazda Press tools 49 G033 107 and 49 H026 103, install a new dust shield cover assembly to the knuckle.
  7. Using the press tools, press a new wheel bearing into the knuckle assembly.
  8. Install or connect the following:
    • Wheel bearing retaining ring
    • New oil seal using Installation tool 49 V001 795
    • Front wheel hub using the Mazda press tools
REAR
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section. NOTE: The wheel bearings are not serviceable. If the bearings are bad, a new hub/bearing assembly must be installed.
  2. Remove or disconnect the following:
    • Rear wheels Fig. 1: Exploded view of the rear wheel hub and bearing assembly (disc brake model shown, drum is similar) 7923mg87.gif

    • Brake drum, if equipped
    • Rear caliper and rotor assembly from the hub, if equipped
    • Hub dust cover
  3. Raise the staked portion of the hub retaining nut with a hammer and chisel.
  4. Remove or disconnect the following:
    • Hub retaining nut and discard it
    • Hub and bearing assembly from the spindle Fig. 2: When installing the new hub nut, be sure to stake it into the notch on the spindle 7923mg86.gif
    To install:
  5. Install or connect the following:
    • Bearing assembly on the spindle. Torque the new nut to 131-173 ft. lbs. (177-235 Nm)
    • Stake the nut into the groove in the spindle
    • Dust cover
    • Assemble the brakes
    • Rear wheel

Jan 01, 2011 | 2002 Mazda Protege

1 Answer

How to change fornt drivers wheel bearing on grand vitara 2002 model 2.0 ltr 5 door and where can i get a repair manual for this model


REMOVAL & INSTALLATION
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove or disconnect the following:
    • Front wheel
    • Brake caliper and rotor
    • Locking hub or hub drive flange, if equipped
    • Hub grease cap, if equipped
    • Wheel speed sensor, if equipped
    • Wheel bearing lockwasher
    • Wheel bearing locknut and inner washer
    • Wheel hub and bearing assembly
    • Wheel hub oil seal
    • Wheel bearing oil seal
    • Snapring
  3. Press the wheel bearing and race out of the hub. To install:
  4. Press the wheel bearing and race into the hub so that the race is fully seated in the hub bore.
  5. Install or connect the following:
    • Snapring
    • Wheel bearing oil seal
    • Wheel hub oil seal
    • Wheel hub and bearing assembly
    • Wheel bearing locknut and inner washer. Tighten the nut to 157 ft. lbs. (216 Nm).
    • Wheel bearing lockwasher. Tighten the retaining screws to 13 inch lbs. (1.5 Nm).
    • Wheel speed sensor, if equipped
    • Hub grease cap, if equipped
    • Locking hub or hub drive flange, if equipped
    • Brake caliper and rotor
    • Front wheel
prev.gif next.gif --- Go to your local auto parts store or library to get a copy of the repair manual for this model.

Aug 26, 2010 | 2002 Suzuki Grand Vitara

1 Answer

Rear wheel hub fluid


Pro honda hypoid gear oil,the dealer will give you the correct weight. 30 weight is what most use

May 27, 2010 | 2006 Yamaha V Star 1100 Custom

1 Answer

How to mainence lube change for rear hub 10 vstar 207


Simply drain old hypoid 30 oil out of the case and refil through the level indicator on the side, you will need to have the rear wheel off the ground while you fill it as you need to spin the back wheel slowly while filling it, keep going untill the oil starts to seep out of the level indicator

Apr 24, 2010 | 2003 Yamaha V Star 1100 Classic

1 Answer

I removed lug nuts from rear wheel on 2006 ram 1500 but wheel is ''stuck'' and cannot be pulled from axle. There is a center ''hub'' on rear but not on front wheel. Can't determine if this ''hub'' should...


Spray some penetrating oil around hub opening, then tap aroung hub with a hammer, it will eventually come off, You are right, it is rusted in place

Mar 06, 2010 | 2006 Dodge Ram 1500

1 Answer

WHAT OIL GOES IN THE FINAL DRIVE, IE: REAR HUB ON THE REAR WHEEL


its going to be some thing like EP80, gear oil not engen oil!!!
thats far to thin and wont take the presher of a gear box,,go for EP80 ,

Oct 24, 2009 | 1997 Honda F6 C Valkyrie

1 Answer

How do I determine if the rear wheel bearings are the problem on my 95 camaro.


Hi there,
first thing you'll have to jack the rear wheels and put the car on axle stands both sides.
Put some good wheel chokes in front and make sure the car is sitting nice on the stands.
Check for any excess play at the wheel hub by moving it side ways and up & down.
Now start the car, put it in drive and let the wheel turn and carefully put your hand on the rear suspension and feel if you sense any "rough" noise or humming noise. This is how you can diagnose the rear wheel bearings.
Cheers

Apr 23, 2009 | Chevrolet Camaro Cars & Trucks

1 Answer

75 series ute rear hub hot after a drive


More than likely its a binding brake. i.e. a sticking wheel cylinder not allowing the shoes to return or a sticking handbrake cable or lever inside the drum.
Last possibility is a worn wheel bearing but thats unlikely to produce a great deal of heat unless it was about to break up. This would be apparent by a fair amount of noise. I'd bet on the first suggestions though.
Cheers John

Dec 17, 2008 | 1993 Toyota Land Cruiser

Not finding what you are looking for?
2005 Triumph Speed triple Logo

114 people viewed this question

Ask a Question

Usually answered in minutes!

Top Triumph Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Triumph Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...