Question about 2008 kawasaki Ninja 250R

1 Answer

Can't undo nut on clutch assembly - 2008 kawasaki Ninja 250R

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 3,567 Answers

You need to get an impact driver. Most any good tool store will have them. Sears if nowhere else. They last forever and are a mechanics most used tool. You usee whatever size socket you want then strike the tool with a hammer. The nut will break free with one or two strikes. Below is a photo. Please rate my answer. Thanks!
Can't undo nut on clutch assembly - tombones49_18.gif

Posted on Mar 27, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i replace clutch master kit?


pipe spanner undo steel pipe line

under the dash
undo pin release .... top of clutch pedal
undo nuts holing clutch master to fire wall
fit new unit

26338805-vgifjk0cmh4fityltrfmb02q-5-0.png

26338805-vgifjk0cmh4fityltrfmb02q-5-1.jpg

Nov 03, 2016 | Cars & Trucks

1 Answer

How to remove a clutch fan from a 1998 Toyota tacoma


Remove the fan from the viscous fan hub. undo the bolts holding the hub to the pump flange and lift out . If the shaft tends to turn when undoing the nuts then use a flat bladed screw driver under an opposing nut across the body of the shaft to act as a lock

Sep 03, 2014 | Cars & Trucks

1 Answer

How do I replace the knife unit in a krups type 243 blender?


Take the blade assembly out of the jug, hold the blades with a towel and turn the driving clutch on the other end. Whichever way the motor turns those blades when operating, you need to turn the drive the opposite way to undo it. If the nut is seized up and wrecks the drive the parts list shows all parts as being available EXCEPT the white bearing housing AND the complete assembled blade and housing.

May 16, 2014 | Blenders

1 Answer

How do i remove the clutch


take side cover off,get spanner to fit clutch nut snugly,hit with hammer clockwise,nut should come loose.undo,remove clutch.dont lose bits

Sep 08, 2013 | McCulloch Eager Beaver 2.1 Parts List

1 Answer

How do i pull the clutch assembly on a 84 fxrs


Disconnect the battery. Drain the primary oil and remove the outer primary cover. Remove the four bolts that hold the clutch spring in. Remove the clutch spring and pressure plate. Then, you can remove the friction and steel plates. If you want to remove the entire clutch assembly, you'll have to remove the nut from the transmission mainshaft and remove the sprocket shaft nut. The mainshaft nut that holds the clutch assembly on has LEFT-HANDED THREADS. Once you get the nut off, you'll need a clutch puller to get the clutch assembly off the tapered transmission mainshaft. Get one of the pullers that screw onto the mainshaft and you rap it with a hammer. You do not have to disassemble the clutch assembly completely to remove it from the mainshaft. You can take it off as a unit by removing the snap ring in the center and removing the adjuster plate. Remove the sprocket shaft nut, the chain adjuster nut, and the mainshaft nut and remove the engine sprocket, primary chain and clutch assembly all together.

Good Luck
steve

Jun 10, 2011 | Harley Davidson FXR Super Glide...

1 Answer

HOW TO CHANGE CLUTCH DRUM


It realy depends on wheather it has an internal clutch, or an external clutch, if the clutch is internal it is a straight forward job, start by removing the retaining c clip from the end of the crank, remove the washer, the drum shoud now just slid off, be carful not to lose the needle bearing, assembly is simply the reverse, if your machine has an external clutch you will need to remove the clutch first, there is normally a nut on the outside of the clutch, or two half circle cut-a-ways in the clutch centre, these are to take a special tool ( a cylinder with two pins and a 19mm nut on the top ) the part number of this tool is 530031112, the clutch is a left hand thread, undo clockwise, do not be tempted to use a screw driver or punch on the centre spider as it may snap the legs off.

Jan 28, 2011 | Poulan Genuine Chain Saw Complete Gasket...

1 Answer

I need to know how to put a new oil gasket 1986 honda xl 100cc. is it as simple as taking out the bolts that hold it on and slide in a new gasket? Thanks


If it is on the right hand side of the bike then yes. Remove the clutch cable by undoing the adjustment nuts on the engine side of the cable and unhooking from the lever. Remove the nut on the gearshift pedal and pull of the pedal. Remove the dipstick. Undo all the nuts on the cover, and remove it. Locate the new gasket on the engine. There are 2 locating dowels so it should not have diffyculty staying in place. Replace the cover and clutch cable and readjust the clutch cable.
On the left hand side of the engine is a bit more tricky as the oil is not leaking past the gasket on the cover itself. There are 2 places where it can leak from. One is behind the drive sprocket. Remove the cover. Undo the nut on the sprocket. Bend back the tabs on the locking plate and remove the sprocket. Drive a self tapping screw into the shaft seal and pull it out with a pair of pliers. Drive a new on back in place. Also see this : http://www.fixya.com/motorcycles/t5649906-1996_yamaha_yz250
If the leak is from behind the alternator you will have to remove the magneto. This is diffycult as you need a puller to get the flywheel off the crank. Then the alternator assembly and only then will you be able to reach the shaft seal. This can be removed as per the previous link.

Aug 18, 2010 | 1986 Honda XL 125 R

1 Answer

How to replace water seal


remove clutch cover,hold water pump shaft on flats on shaft and undo impellor by nut cast on impellor. remove old bearings and seals.check shaft for grooving where seal runs and replace if any.assemble in reverse order with new seals and bearings etc

Jun 22, 2010 | 2004 Yamaha YZ 450 F

1 Answer

I need to change the clutch on my 1981 Kawasawki KE125


It should be under the left side engine case. un do case screws, remove clutch cable, the clutch should have a series of plates and are held in a basket with a big nut in the centre holding it on to the crank, remove nut and it all should slide off towards you. replace plates and replace every thing in the reverse order, when done make sure that there is 1/4 inch of play in the adjustment of the clutch lever. This means when you pull in the clutch you should not feel any resistance for the first 1/4 clutch lever travel. also when trying to undo clutch centre nut, put the bike in gear and put a steel bar through the spokes of the wheel held against the swing arm to lock up the engine to undo the nut and tighten it.

Apr 24, 2010 | 1981 kawasaki KE 125

Not finding what you are looking for?
2008 kawasaki Ninja 250R Logo

Related Topics:

58 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...