Question about 2005 Suzuki Boulevard C50

1 Answer

How top remove seats - 2005 Suzuki Boulevard C50

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 33 Answers

  • Lift the rear of the passenger seat's cushion to find the screw that secures the seat to the rear fender. Use a 5-mm Allen wrench to remove the screw.


  • Lift the rear of the passenger seat slightly and pull it away from the rider's seat.


  • Use the 5-mm Allen wrench to remove the screws from the rear of the rider's seat.


  • Lift the rear of the rider's seat upward slightly. Pull the seat back until the tabs on the front of the seat separate from the motorcycle's frame.


  • Posted on Mar 27, 2011

    1 Suggested Answer

    6ya6ya
    • 2 Answers

    SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

    Hi,
    a 6ya expert can help you resolve that issue over the phone in a minute or two.
    best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
    the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
    click here to download the app (for users in the US for now) and get all the help you need.
    goodluck!

    Posted on Jan 02, 2017

    Add Your Answer

    Uploading: 0%

    my-video-file.mp4

    Complete. Click "Add" to insert your video. Add

    ×

    Loading...
    Loading...

    Related Questions:

    1 Answer

    How to remove the top part of the back seat in a 2007 Dodge Charger


    911 Signal USA's Dodge Charger Demo Vehicle Back Seat ...

    ? 0:45
    https://www.youtube.com/watch?v=8pW-FpK1E7I
    Jul 30, 2013 - Uploaded by 911 Signal USA
    Removing the top of the back seat can be done by repeating the steps ... Removing a Dodge Charger Rear ...

    Nov 19, 2015 | Dodge Cars & Trucks

    1 Answer

    How to remove right rear seat on a 2014 porsche cayenne


    I'm not sure what exactly your asking here, as these seats have built in levers on the top left that requires you to pull them forward releasing the catch at the top of the seat. You must pull the bottom of the seat up first, then remove the headrests and place them in the slots located on the bottom part of the seat. This is for convenience of storage for them. If the lever has broken as this is the case with many, you need to get a screwdriver to lift up the catch on the back of the top part of the seat. If you want to remove the seat entirely you'll need to purchase triple square sockets. I think it's a T20. I beleive it's the same size as for the bolts to remove the front seat to gain access to the battery.

    Nov 12, 2014 | 2014 Porsche Cayenne

    1 Answer

    Remove Rear Seat


    Fold the top of the back seat down. My 1990 civic lx has a place to put your key at the top to release the seat. Remove the trunk carpet from the seat back by pulling out the plastic screws. Remove 2 bolts (10 mm) on each side holding the seat on a bracket. The top part of the seat should now slide out. Once you get the top part of the seat out, a bolt should be exposed just to the right of the center of the seat bottom attaching it to the floor. Unscrew the bolt. Now tip the seat bottom up and forward. There are two hooks to the front of the seat bottom. You will have to move the seat back and forth a few times to unhook them and then pull the hooks out of the slots on the floor.

    Apr 27, 2013 | 1990 Honda Civic

    1 Answer

    Does 2003 buick lasabre have access panel for skis in middle of rear seat


    In the trunk of the car there is a black panel behind the rear seat remove screws that hold this panel on. There are three magnets at the top of the panel. Remove panel and put screws in safe place. Go back to the inside of the vehicle there are three brackets that hold in top cover of back seat remove that lay it down in the back seat. You now have complete access from the rear seat to the trunk. To reassemble reattach rear seat top. Reassemble black panel in trunk just attach to metal with magnets and then put screws back in. Hope this is helpful and informative.

    Aug 05, 2012 | 2003 Buick LeSabre

    1 Answer

    I can't into my trunk there is something stuck therefore i need to fold down my rear seats and move it but i don't know how to fold them down I trie but i got nowhere


    Be sure that your model has fold down rear seats...you should see the seperation around both rear seats...if equipped, the fold down release is located at the top corner of each rear seat...pull the lever up to release...if your model does not have the fold down option...you will need to remove the rear seat...remove the lower cushions first...look on the lower front of the seats for hold down bolts...second you will need to remove the top of the rear seat...hold down bolts are at the bottom of the top cushion...after removing the bolts (one each side) you need to push up on the cushion to remove...this will then allow access to the trunk...find the trunk latch and try to release by twisting the latch cable...Hope this helps...

    Jan 20, 2011 | Pontiac Sunfire Cars & Trucks

    1 Answer

    Remove the back seat from chevy celebrty 1987


    Push lower end of rear seat back to unlock clips (takes a bit of effort)
    Lift bench out
    Should be clips or bolts holding the top of the rear seat - release these
    Push up on the upper section of seat to release top clips.
    in some car models
    Remove the 10mm bolt behind the bench near the seat belt fastening sight and then lift the seat up from the back to the front..towards the front seats. The clips are angled down and in so that the back has to lift up first.
    This will help. Thanks please keep updated. please please do rate the solution positively .thank you for using fixya

    Mar 18, 2010 | 1987 Chevrolet Celebrity

    1 Answer

    How to remove rear seat back 1987 mustang convertable?


    Tools Required:
    • 3/8 inch Drive Ratchet
    • 3/8 inch Drive 3” Extension
    • 3/8 inch Drive 10mm Socket
    • 3/8 inch Drive 13mm Socket
    • T-50 Torx Bit
    • 1/4 inch Allen Wrench
    • 3/16 inch Allen Wrench
    • 1/2 inch Wrench
    • Drill Motor
    • 1/8 inch Drill Bit
    • 5/16 inch Drill Bit
    • 2 inch Hole Saw
    • Trim Tool (Fork Tool)
    • Electrical Tape
    • Center Punch
    • Hammer
    ------------------- Installation:

    Remove Back Seat:
    1. Locate the retainers securing the seat bottom into the vehicle, approximately 10 inches from the end of the cushion, either side. Use your thumb to push in retainer release tab. Lift the seat up to remove.
    2. Remove the two 13mm screws securing the seat back, located on each lower corner. Lift seat upward to release seat back from brackets at the top. You can carefully prop the seat back under the retracted top , use caution if choosing this method not to damage or scratch the vinyl of the seat. You can remove the seat from the vehicle completely by disengaging the flanges securing the top of the rear seat to the fabric of the convertible top well .
    3. Remove Quarter Trim Panels:
      1. Grip the Quarter Trim Panel Cap at the shoulder strap opening and lift up to dislodge the retaining clips.
      2. The inside Quarter Trim Panels are two-piece panels. Remove the upper portion of the Quarter Trim Panel from the vehicle; it is not necessary to remove the lower portion. Pull the forward edge of the trim Panel over the pinch weld in the doorjamb.
      3. Use a Door Trim Tool (Fork Tool) to dislodge the pushpin retainer at the rear edge of the Trim Panel approximately 4” down from the top, pry Trim Panel toward the outside of car to release retainer.
      for more help click this link directly
      1. http://www.americanmuscle.com/05-07-lightbar-install.html ---------

    Oct 05, 2009 | 1987 Ford Mustang

    2 Answers

    On a 1989 nissan maxima with sonar suspension II how do you disassemble the strut assembly? the mounting bracket for sonar adapters is in the way of the strut center bolt.


    First you must remove the rear seat to gain access to the top strut mounts. The bottom of the rear seat comes out first. On the 91 model there are two tabs at the base of the seat bottm that you pull forward to release the seat bottom. I'm not sure if the 89 is the same. After removal of the rear seat bottom, you will see a bolt at the bottom of each side of the rear seat back that need to be removed. Fold down the arm rest and disconnect the vinyl cover at the base of the armrest to expose and remove two screws. Push up on the rear seat back to unhook three plastic hooks (center and one at each end) at the top of the rear seat back. Remove the seat back. Remove the large metal support panel that is behind the seat back. Safely jack up the rear of the car and support on jack stands so the rear wheels hang free. Doing one strut at a time, remove the two top strut mount bolts leaving the center strut stud nut in place. The strut and mount will lower out of the unibody. Disconnect the bottom strut mount. Remove the strut/coil spring assembly. Using a strut/spring compressor (some auto parts stores rent these) compress the spring. Carefully remove the top strut stud retaining nut, top strut mount, bumpers and strut boot. Carefully install compressed spring, strut boot, bumpers and top strut mount on new strut and install washer and retaining nut. Reinstall strut and etc. in reverse order.

    Sep 15, 2009 | 1989 Nissan Maxima

    1 Answer

    Need to clean carseat al eddie bauer online manuals aren't availa


    First, snap out the black pieces that attach the cover to the seat with a pair of pliers or a kitchen knife. Then turn the seat over and remove the base by sliding out the metal rod that runs thru the base and seat. Then unhook the center buckle from the bottom of the seat and back up thru the seat. Unhook the straps from the metal bar on the back of the seat and thread them back thru the seat. Be sure to remember the order in which you slide it thru the components so you can reassemble. It may be helpful to lay them out in the order you removed them. Unhook the elastic bands holding the bottom in place and slide it over the top part of the seat and off the seat. If you need to remove the top part and wash, remove the black pieces the same way as the bottom, unhook all elastic and slip it off the top. I wash mine in cold water with mild detergent and usually let it air dry so as to not shrink it. Reassemble by reversing steps.

    Jun 06, 2009 | Eddie Bauer 3-In-1 with Latch

    3 Answers

    Where is my battery


    Most M/C have the battery located under the seat. Remove the seat and you will see the top of the battery.

    May 08, 2009 | 2005 Suzuki Boulevard C50

    Not finding what you are looking for?
    2005 Suzuki Boulevard C50 Logo

    1,008 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Suzuki Experts

    yadayada
    yadayada

    Level 3 Expert

    75797 Answers

    Arnie Burke
    Arnie Burke

    Level 3 Expert

    4514 Answers

    Ed Nelson
    Ed Nelson

    Level 2 Expert

    149 Answers

    Are you a Suzuki Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...