Question about Suzuki RGV 250 T Motorcycles

Open Question

Need to know where timing marks for timing chain replacement on 250 quad bike, suzuki VIN No.AJ41B-101907

Posted by Anonymous on


3 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

  • 149 Answers

SOURCE: 1994 Suzuki King Quad Timing Specs?

sent you via email. let me know what else you need while I have the manual...

Posted on Jan 15, 2009

  • 3567 Answers

SOURCE: timing chain 110 hymoto pit bike

Put the piston at TDC (Top Dead Center) by lining up the timing marks on the flywheel and stator. Put the cylinder head back together with the cam installed so the high points of the cam lobes are pointing kind of downward. Pull the cam chain taught on the front side of the engine. Put the chain on the cam gear such that, when bolted to the cam, the index mark or marks are in the proper position.

The proper position depends on what markings are on the cam. Some bikes have a single mark; an arrow, a straight line or an "O". The mark should line up with the center-line of the crankshaft. If the cam has two marks opposite each other, the lines should be parallel with the gasket surface. You will need to rotate the unbolted cam left or right just a bit in order to match up the bolt holes to the gear holes.

Can I get a “very helpful” rating on this answer?


Posted on Aug 20, 2009

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

On a 95 suzuki king quad 300 do u have to break the engine in half to replace the piston rings

The valve train, head and cylinder must be removed from the transmission, possibly even the fuel system. You should replace the base gasket as well as the head gasket while reassembling. Be careful to not let the timing chain drop into the transmission and make note of the timing marks as well prior to disassembly. Tie the chain with a string while you slip the cylinder off the piston.

Mar 25, 2015 | Suzuki Motorcycles

1 Answer

Need to know what year this dirt bike is serial number js1rf15cy2100862 it a suzuki 125

The VIN listed has only 16 digits. There should be 17 digits. Recheck the numbers then go to the following website to decode the VIN. Then you will know exactly what bike you have. Please rate my answer. Thanks.

Jul 23, 2011 | Suzuki RM 125 Motorcycles

2 Answers

How to set the timing chain on a 2005 kawasaki

Timing chain marks??? Or marks on your cams?? On the cams you should have 2 marks on each side of your cam sprocket. They should be even with the top of your jug...

Dec 29, 2009 | 2005 kawasaki KX 250

1 Answer

Where are all the timing marks for a 2005 Suzuki LTZ 250 quad. I am rebuilding the top end and need to set-up the timing order? Dave

usually timing marks are on the flywheel or rotor of the alternator. Usually on the opposite side of the gear case. I think that would be the right side on your machine.

Oct 21, 2009 | 2001 Suzuki DR-Z 250

2 Answers

How do I tighten the chain on my 1985 Honda 200X

eleavate the back wheel,lossen wheel, lossen chain adjusters, make sure both sides are at the exact mark and back and tighten pull

Jul 16, 2009 | 2005 Suzuki RM-Z 250

1 Answer

Want to remove rear timing chain tensioner guide on '98 tE410

i took the chin off a suzuki quad (4 stroke) and only had to remove the vavle cover/valves, and the crankcase cover. the crank was marked and the cam was marked so it was easier to set the correct timing. if you have a 2 stroke it shouldn't be much diffrent

Jun 20, 2009 | 2000 Husqvarna TE 410

3 Answers

Timing a 250 drz suzuki

I have a dr-z 250 suzuki and i replaced piston and rings. Dont know how to reset timing chain and cam gears. does eney body know how to set the timing on this bike.

Mar 25, 2009 | 2001 Suzuki DR-Z 250

1 Answer


Go to any reputable shop/mechanic; you probably need a new chain and/or sprocket...OR Possibly just a chain adjustment. Don't wait around, do it asap, I wouldn' t play with this particular problem.

Nov 20, 2008 | 1990 Suzuki RGV 250 L

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

460 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts


Level 3 Expert

81400 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

5060 Answers


Level 2 Expert

83 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides