Question about kawasaki KX 125 Motorcycles

1 Answer

I have a bog or hesitation on hard acceleration bike seems to have good compression starts first kick hot or cold i can make it go away but must completely seat mixture screw checked airfilter and intake

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 133 Answers

You might have to make sure that the carb is clear of any gunk ( very important )

Posted on Mar 26, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why is my carb bogging out on acceleration?


check the air filter or try running it with the lid off the airbox

May 04, 2014 | ATVs

1 Answer

Gilera runner 50sp 06 (New shape) keeps bogging out when acc


why is my gilera bogging out when i drvie it on the flat

Nov 24, 2009 | 2006 Gilera Runner VX 125

1 Answer

I cant start the bike


There is a proper way to start the engine. Four controls are on your bike to assist in starting. Below are generic instructions.
  • The choke, used when the engine is cold. Pull the red knob for choke.
  • The " Hot Start " Lever, used when the engine is hot. Pull the lever to lean the fuel mix when the engine has been running.
  • The de-compression lever, always used.
  • The throttle, used to prime the cylinder.
Don't kick, instead, push the kick lever downward. You will feel the back pressure as the piston is going upward on the compression stroke to the point the pressure is great enough that the kick lever "locks up". You are very close to TDC. NOW, pull in the de-compression lever. Push the kick lever a little bit more to get the piston past TDC. Now release the de-compression lever. Give the throttle a 1/4 turn then let it snap closed. A diaphragm in the carb gives a shot of gas when this is done. DO NOT do this multiple times because you will flood the engine. Leave the throttle closed when kicking. A flooded engine will often backfire. Now give a strong kick through the full sweep of the kick start lever. Quickly get your foot off the kick lever at the end of the kick to avoid any chance of "kickback" from the kick lever. This happens in the case of a misfire, aka > backfire. It can be very painful, and can even break a leg. I am serious about that. Repeat the process (but without the throttle priming), for six kicks. After six kicks go ahead and twist the throttle again for a second priming. A good battery, a clean spark plug, a clean carb and clean air filter will also aid in starting.

Nov 14, 2009 | 2006 kawasaki KX 250 F

1 Answer

2007 honda crf 250 r hard starting when cold ,


There is a proper way to start an engine. Most bikes have four controls to assist in starting.
  • The choke, used when the engine is cold. Pull the red knob for choke.
  • The " Hot Start " Lever, used when the engine is hot. Pull the lever to lean the fuel mix when the engine has been running.
  • The de-compression lever, always used.
  • The throttle, used to prime the cylinder.
Don't kick, instead, push the kick lever downward. You will feel the back pressure as the piston is going upward on the compression stroke to the point the pressure is great enough that the kick lever "locks up". You are very close to TDC. NOW, pull in the de-compression lever. Push the kick lever a little bit more to get the piston past TDC. Now release the de-compression lever. Give the throttle a 1/4 turn then let it snap closed. A diaphragm in the carb gives a shot of gas when this is done. DO NOT do this multiple times because you will flood the engine. Leave the throttle closed when kicking. A flooded engine will often backfire. Now give a strong kick through the full sweep of the kick start lever. Quickly get your foot off the kick lever at the end of the kick to avoid any chance of "kickback" from the kick lever. This happens in the case of a misfire, aka > backfire. It can be very painful, and can even break a leg. I am serious about that. Repeat the process (but without the throttle priming), until the bike starts. Go ahead and give it another primer shot after the 5th kick attempt. A good battery, a clean spark plug, a clean carb and clean air filter will also aid in starting.

Sep 23, 2009 | 2005 Honda CRF 250 R

2 Answers

Yz450f that quit running


Yes, it does have an automatic decompression mechanism. It is a centrifugally operated mechanism and it is EXTREMELY unlikely that is causing your problems.
The two highest probabilities are:
1. Fouled spark plug. Forget what it looks like, put a BRAND NEW plug in. It is the cheapest form of diagnosis you can do. These bikes are terrible about fouling spark plugs and a fouled plug produces the exact symptoms you described.
2. Inspect your valve clearance. Tight valves will also make the bike hard/impossible to start with the kick starter. In some cases, it can be push started, but still won't kick. With tight valves, the bike, although hard starting, will run pretty good, for awhile. Eventually it will burn the valves and quit running though.
If your bike isn't kick starting fairly easily, something is wrong and needs to be addressed. The only other issue is making sure the idle speed is set per the service manual. These bikes have a fairly high idle, some as high as 1700 rpms. If it is set too low, it makes them hard to start too.

Sep 11, 2009 | 2004 Yamaha YZ 450 F

1 Answer

Bike is sometimes hard to start.When bike stalls and goes dead,it is hard to start again.This is a 2003 honda crf450.


There is a proper way to start the engine. Four controls are on your bike to assist in starting.
  • The choke, used when the engine is cold. Pull the red knob for choke.
  • The " Hot Start " Lever, used when the engine is hot. Pull the lever to lean the fuel mix when the engine has been running.
  • The de-compression lever, always used.
  • The throttle, used to prime the cylinder.
Don't kick, instead, push the kick lever downward. You will feel the back pressure as the piston is going upward on the compression stroke to the point the pressure is great enough that the kick lever "locks up". You are very close to TDC. NOW, pull in the de-compression lever. Push the kick lever a little bit more to get the piston past TDC. Now release the de-compression lever. Give the throttle a 1/4 turn then let it snap closed. A diaphragm in the carb gives a shot of gas when this is done. DO NOT do this multiple times because you will flood the engine. Leave the throttle closed when kicking. A flooded engine will often backfire. Now give a strong kick through the full sweep of the kick start lever. Quickly get your foot off the kick lever at the end of the kick to avoid any chance of "kickback" from the kick lever. This happens in the case of a misfire, aka > backfire. It can be very painful, and can even break a leg. I am serious about that. Repeat the process (but without the throttle priming), until the bike starts. A good battery, a clean spark plug, a clean carb and clean air filter will also aid in starting.

Jun 28, 2009 | 2003 Honda CRF 450 R

2 Answers

VERY hard starting takes way to many kicks usually play out befo


There is a proper way to start the engine. Four controls are on your bike to assist in starting.
  • The choke, used when the engine is cold. Pull the red knob for choke.
  • The " Hot Start " Lever, used when the engine is hot. Pull the lever to lean the fuel mix when the engine has been running.
  • The de-compression lever, always used.
  • The throttle, used to prime the cylinder.
Don't kick, instead, push the kick lever downward. You will feel the back pressure as the piston is going upward on the compression stroke to the point the pressure is great enough that the kick lever "locks up". You are very close to TDC. NOW, pull in the de-compression lever. Push the kick lever a little bit more to get the piston past TDC. Release the de-compression lever. Give the throttle a 1/4 turn then let it snap closed. A diaphragm in the carb gives a shot of gas when this is done. DO NOT do this multiple times because you will flood the engine. Leave the throttle closed when kicking. Give a strong kick through the full sweep of the kickstart lever. Quickly get your foot off the kick lever at the end of the kick to avoid any chance of "kickback" from a backfire. It can be very painful, and can even break a leg. I am serious about that. Repeat the process (but without the throttle priming), until the bike starts. A good battery, a clean spark plug, a clean carb and clean air filter will also aid in starting.

Top rating for this answer? Thanks!

Jun 11, 2009 | 2003 Yamaha YZ 250 F

1 Answer

2005 250 f 65 kicks to start


Several things can cause the problem. First, spring for a new spark plug. The stock plug is NGK CR8E. Now the plug is eliminated as a problem. Next, pull the slide out of the throat of the carb. Now remove the jet needle. Put the needle clip on the 4th notch, (this is the stock setting). Use only premium gas. Next, follow the starting instructions below.

There is a proper way to start the engine. Four controls are on your bike to assist in starting.
  • The choke, used when the engine is cold. Pull the red knob for choke.
  • The " Hot Start " Lever, used when the engine is hot. Pull the lever to lean the fuel mix when the engine has been running.
  • The de-compression lever, always used.
  • The throttle, used to prime the cylinder.
Don't kick, instead, push the kick lever downward. You will feel the back pressure as the piston is going upward on the compression stroke to the point the pressure is great enough that the kick lever "locks up". You are very close to TDC. NOW, pull in the de-compression lever. Push the kick lever a little bit more to get the piston past TDC. Give the throttle a 1/4 turn then let it snap closed. A diaphragm in the carb gives a shot of gas when this is done. DO NOT do this multiple times because you will flood the engine. Leave the throttle closed when kicking. Release the de-compression lever and give a strong kick through the full sweep of the kick start lever. Quickly get your foot off the kick lever at the end of the kick to avoid any chance of "kickback" from a backfire. It can be very painful, and can even break a leg. I am serious about that. Repeat the process (but without the throttle priming), until the bike starts. A good battery and clean air filter will also aid in starting.

This will likely tame the beast for you. Please rate this answer. Thanks!

Jun 06, 2009 | 2003 Yamaha YZ 250 F

2 Answers

Bogging 1994 Suzuki RM 125


i have the same problem on the exact same bike

Apr 07, 2009 | Suzuki RM 125 Motorcycles

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

184 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

5057 Answers

Marvin
Marvin

Level 3 Expert

81400 Answers

bazzz7071
bazzz7071

Level 2 Expert

342 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...