Question about kawasaki ZX-9R Motorcycles

1 Answer

Starter solinord ckilcks i have also crossed the contacts on solinord but no spark . new battrey fitted

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,978 Answers

Tap on the starter gently with a plastic hammer while holding the starter button. If the starter works now you need starter brushes. The brushes are about the only replacement part available on Japanese motorcycle starters. Unbolt the power cable to the starter, take off the two bolts holding the starter to the case, and pull the starter out of the motor. Now you can take off the end cap to inspect the brushes. Installation is reverse order. bench test the starter before reinstalling. If the spline of the starter does not mesh with the spline hole of the gear in the motor, rotate the starter enough so the splines line up or power the motor to move the position of the spline and try again. If you have an Ohm meter you can easily test the armature. You should have continuity between every other contact. But no continuity between adjacent contacts. If there is anything other than brushes wrong with the starter you will have to replace the assembly.

Posted on Mar 26, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

It won't start when you turn on the key. I put in a new battery and starter.


take the plug off the back of the ign switch and clean contacts,also check the fuse while you are right there

May 01, 2015 | Garden

1 Answer

I have a 2010 4x4,4010 diesel that does not crank over. New battery,all fuses look good. No power to dash lights when turning key on. Any suggestions?. I don't have a manual,does this have a ignition?


Have you checked you have a good Earth on you can and also check the wires to the starter motor that they are in place and make sure your starter solinord is working .

Feb 04, 2015 | Cars & Trucks

1 Answer

Bmw immobiliser problems


I suggest you look closely at the connections at the following places
Battrey Terminals
Ground cable to frame and crankcase
poaitive connection to starter solenoid
starter solenoid connection to starter
any corrosion at any point above will cause a voltage drop during starting and miss with the computer perhaps requiring a reset of the immobilized (no spark no fuel injection) bike.

Dec 20, 2017 | Motorcycles

1 Answer

How to replace a starter on toyota corolla 1999


Make sure you have your radio code if needed otherwise the radio won't work after this. Disconect battry, Unbolt main wire from starter, disconect switch wire from starter, unbolt starter, remove starter, fit new starter, connect switch wire, connect main wire to starter, connect battrey, start a couple of times to make sure all ok, input radio code.

Jun 24, 2012 | 1999 Toyota Corolla

1 Answer

1984 Buick Regal. Need to know where wires from starter leads and attaches to. Thank you.


coming from the starter you will have one going to bttery and one going to alternater and should have one that goes to the relay or solinord to the best of my knowledge

Feb 26, 2011 | 1984 Buick Regal

2 Answers

Situation: My battery has died. I would like to place my car in Neutral so that I can have another car give me a jump. Problem: I cannot place my car in neutral because my car will not allow me to...


You need a portable jump starter, may be a friend has one, or swap batteries with another car that has a battery similar to yours (I.E. top vs Side posts and size) a size that will fit same or a little smaller OK and polarity same so you don't cross connect or reverse the polarity remember the + red post goes to red+ and the - black goes to black- post. Then start move car to roomier area then swap battery back then jump start to get it home. and remember to charge your battery with a charger driving does not fully charge and a low battrey may start your car but it makes the starter get hotter from pulling higher amps for a longer time.
Patrick Mot

Feb 12, 2011 | 1994 Toyota Camry

1 Answer

New battrey fitted , new alternator as well but will still not start


You did not give much information to go on. I am assuming the starter is turning, but the engine won't start. So, it must be a fuel or spark related issue. The first thing to do is establish which it is. You can do this by removing one spark plug. First try to start the engine. Then remove the spark plug. Look at the tip of the spark plug. If the engine is getting fuel, the spark plug will be wet and smell of gasoline. That would indicate a problem with spark. If the spark plug is dry, then the problem would be fuel related. If you could provide a little more information please, what year and model is your Ford, and what were the circumstances leading up to the problem. Was the car starting ok before you replaced the battery? One thing you can check very quickly is the "Inertia Switch", or as it is called, the "fuel shutoff switch". Depending on which model and year of Ford you have, the switch could be located behind the passenger side front kick panel, or just under the carpet in the passenger side footwell up near the dash. If you are able to locate the switch, push the reset button and try to start the car. It is possible something tripped the inertia switch and shut the fuel pump down.

Feb 02, 2011 | Ford Focus Cars & Trucks

1 Answer

Car don't want to start?


check your battrey. alternator. fuseable link wire going from the starter to the alternator. check battrey connections. spark plugs. and pulg wires

Apr 10, 2009 | 1988 Toyota Corolla 4 Door

1 Answer

Cant get my lawn tractor to start


IT COULD BE IGNITION SWITCH IS BAD, I REPLACED ONE ON A CRAFTSMAN THAT DID THIS,BUT ALSO COULD BE A SAFETY SWITCH IS NOT CLOSED PREVENTING STARTER FROM OPERATING,---WITH THE IGNITION SET TO ON CROSS THE TERMINALS ON SOLENOID AND SEE IF IT STARTS THE TRACTOR RUNNING, IF IT FAILS TO RUN ITS PROBALY THE IGNITION SWITCH THEN.

Apr 09, 2009 | Briggs & Stratton Garden

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

228 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

5057 Answers

Marvin
Marvin

Level 3 Expert

81400 Answers

bazzz7071
bazzz7071

Level 2 Expert

342 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...