Question about Suzuki VZ 800 Marauder Motorcycles

1 Answer

I figure it's under the gas tank, I took off the two bolts by the seat that hold the tank, but it dont pull right off. I don't want to break anything so I am hopeing for some insight. Thanks in advance Alexs

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    MVP:

    An expert that gotĀ 5 achievements.

    Master:

    An expert who has achieved Level 3.

    Sergeant:

    An expert that hasĀ over 500 points.

  • Suzuki Master
  • 500 Answers

I believe the tank is held on after the bolts are removed by rubber pucks at front wiggle ..to the rear ..1st remove the gas line...

Posted on Mar 25, 2011

Testimonial: "thank U 4 your help, it all worked out fine."

  • safetyalex Mar 25, 2011

    When I remove the gas lines, I am guessing the lines will leak?
    Do I first have to empty the tank and what will the process be. All I really want to do is just chance the spark plugs.
    I never thought it would consist of so much work.

  • Mot Smith
    Mot Smith Mar 25, 2011

    Well just see if gently lifting gives you enough room with out disconecting gas line. otherwise just shut off petcock or youll need to drain tank if drain tank good time to check filter & clean ,,

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Take the seat off


  • Open tool box, at rear of seat, with key and unhook or unbolt the seat from inside tool box.
  • Pull lever on right or left side, up under the seat. It can also be at the rear of the seat, right or left side, again up under the seat. Lift seat off up and to the rear. Sometimes it's hooked on both sides with a rod or cable connecting both sides. These can break. Make sure both are unhooking.
  • Same as above only you use a key.
  • Remove the two bolts on either side at the rear of the seat. Pull seat to rear.
  • Nuts or bolts, at the rear and below seat, under the rear fender Remove bolts holding down the rear seat . Remove seat and then remove two bolts, at the rear, holding the front seat on.
  • Unlock lever on side of seat. Seat then pivots on two hinges to open. Can open to the right or left. Might have no lock.
  • Push button on side. Left side, I haven't found a push button on the right side... yet ! Can be locked or unlocked with a key.
  • Pull lever at front of seat, right or left side. Seat lifts up with the hinge at the rear.
  • Pull lever at rear of seat, right or left side. Seat lifts up with hinge at front.
  • Pull lever at front of seat, right or left, and whole seat comes off. Seat has pegs underneath that fit into rubber grommets on the frame.
  • Dec 10, 2013 | Motorcycles

    1 Answer

    Im going to need to drop my fuel tank in my 1986 camry. I have never done it before but I am capable. So If anyone knows how to do this please help. I dont want to break anything. First Im going to open...


    First disconnect the negative terminal of the battery. Next left out the back seat. It is spring clipped in with two clips on the bottom left and right front of the seat. Pull clips forward and lift seat front up. I hooks in at the back so rotate the front up to unhook and lift out. In the middle under the seat is the gas gage float. Disconnect the wire connector and remove floor cover with Philips screwdriver. Then remove float from tank. This step must be done so you do not break the wire to the gas gage float. It is also the best place to siphon off the gas in the tank. Then you can remove the tank. You may have an exhaust shield to remove. The tank is held in with two straps hinged in the front and bolted in the back. Loosen the brake line clamps attached to the straps so that the clamp will slip when the tank straps are hinged down. There are several hoses and a gas connect to open. Open hose clamps. Disconnect fuel pump connector at back of tank. The fill hose needs to be worked off as you pull the tank down. There is one hose on the top back edge of the tank that needs disconnect after the tank is tipped down some. There is a rubber/plastic tank holder connected to the back flange of the gas tank. Remove the two corner screws but leave the guard connected to the straps. Remove the two strap bolts and hinge down to pull it out and disconnect all hoses. Mark with tape or some mean which hose when were.

    Jan 25, 2013 | 1986 Toyota Camry

    1 Answer

    Handlebars are bent


    Instructions

    YZF600R (1994 - 2007)
    1

    Insert the ignition key into the seat lock, located on the left side of the tail fairing above the left passenger foot peg. Twist the key clockwise to release the seat lock mechanism.
    2

    Grasp the rear portion of the seat and lift it off of the motorcycle's subframe. Pull the front of the seat away from the gas tank until the tab under the front of the seat is free of the subframe.

    3

    Hold the seat over the subframe to reinstall it. Hook the seat's tab under the cross-member below the base of the gas tank.
    4

    Push the seat forward slightly, then lower the rear of the seat onto the motorcycle's subframe.
    5

    Push down on the rear of the seat until the seat lock mechanism clicks into place. Remove the ignition key from the seat lock.
    YZF-R6 (1998 - Present)
    6

    Insert the ignition key into the seat lock on the left side of the tail fairing. 2006 and newer R6 models place the seat lock under the tail fairing, near the left rear foot peg. Twist the key clockwise to release the seat lock mechanism.
    7

    Grasp the rear of the passenger seat and lift it up slightly. Pull the seat toward the rear of the motorcycle until the hooks under the front of the seat are free of the tabs built into the subframe under the tail fairing.
    8

    Pull the rear corners of the rider's seat up to reveal both mounting bolts. Unscrew the bolts with a 5 mm Allen wrench. Lift the rear of the seat up, then pull it away from the gas tank until the tabs under the front of the seat are free of the cross-member below the base of the gas tank.
    9

    Slide the rider's seat tabs under the frame cross-member to reinstall the seat. Lower the back of the seat onto the subframe, then screw the mounting bolts into place with a 5 mm Allen wrench.
    10

    Hook the front of the passenger seat onto the tabs built into the subframe under the tail fairing. Lower the seat onto the fairing and press down until the seat lock mechanism clicks into place. Remove the ignition key from the seat lock.

    Jan 15, 2013 | Yamaha XT 125 X Motorcycles

    1 Answer

    How do i remove the fuel tank on kawasaki zzr110


    take the seat off there are two 10mm bolts holding the rear of the tank remove the fuel line clamp andthen two wire guage connector under the seat then the two bolts at the front of the tank pull it up slowly the tank has two small hoses that are at the back of the tank but not connected to anything they are vents

    Mar 18, 2012 | 1996 kawasaki ZZR 1100

    1 Answer

    How to remove gas tank


    Turn the petcoc(k) off and remove the fuel line. Next, remove the seat - remove the rear seat first then the front. Under the nose of the seat you will see a large bracket with two bolts - remove the bolts. There is a plastic tray holding electronics that is also attached to this bracket - push the center pin of the fastener down and the plug will come out (push it up, insert and push the pin flush to re-install). Next, lift the back of the tank and bracket up a little and pull it straight back and the tank will lift right off. The front of the tank is held in place by two little pockets - you will see this after the tank is off.

    I hope this helps!

    Jun 03, 2010 | 2007 Yamaha Road Star

    1 Answer

    I need to change the spark plug on my 1996 suzuki savage , I have removed the seat as well as the 2 bolts that hold the gas tank under that seat ,having trouble from there it won't lift off help please


    I took mine off last night for the first time. Once you remove the 2 bolts at the back of the tank then you have to work it loose. generally pull up and back on the rear end of the tank, and then up and to the left as it starts to loosen. The reason you need to pull to the left is that the fuel selector valve will start to interfere with the throttle cable once the tank moves backward, and twisting the back of the tank towards the left will let the valve go around the cable. Take a look and you'll see what I mean. Took a while working it back and forth to get it off, but I finally did. Some people recommend you drain the tank and remove the fuel valve as an alternative but I didn't need to do that.

    Mar 20, 2010 | 1996 Suzuki LS 650 Savage

    1 Answer

    1100 yamaha 2003 vstar classic gas tank remove


    1) Make sure your fuel petcock is closed, then detach the gas line coming off it (left underside of tank)
    2) Remove the back seat (single acorn nut on rear fender)
    3) Remove the front seat (two allen bolts at the back of seat)
    4) There are two metric 12mm bolts under the front seat that hold the tank down. Remove them. The tank should be sitting loose on bike, but connected by some wires
    5) Disconnect the white wiring harness under the bike. Tank is now totally free to remove.
    6) Pull tank up and back at the same time, it will slide off the two rubber mounts at the front.

    Jan 28, 2010 | 2003 Yamaha V Star 1100 Classic

    2 Answers

    How to remove gas tank


    first of this years models petcock is on the right hand side of the bike built into the side cover so first pull off the side cover making sure not to break any of the tabs off.now unbolt the petcock making sure it's in the off position,now what i do if i have gas in the tank is add a long hose where the gas filter is an drain it into an apropriate container(you must drain the tank as if you don't when you remove the main gas line under the seat you'll have a gas mess on your hands)after fully draining the tank now take the bpassenger seat off by removing the tool box an the 2 10 mill bolts,after that remove the driver seat also 2 10 mil bolts,after that you'll see there's 2 gas lines a smaller 1 to the right and a larger 1 in the center,what i do is remove the clamps from the reserve tank that they feed,now take the center bolt off the tank and then the 2 side bolts up front and slide the tank up an forward being careful not to break the lines,while the tank is off inspect alllines an replace if they look dry rotted or cracked hope this has helped you out John a 1985 shadow owner himself

    Jan 01, 2010 | 1985 Honda VT 500 C Shadow

    1 Answer

    How do you remove the gas tank from the tw200 2003. I have got the bolts that held it closer to the back but i cant figure out how to undue the front.


    There are two seat bolts under the seat that must be removed. Obviously, if the underside of the fender is covered in mud, you'll have to clean it first. A metric socket works best to remove the bolts.

    After removal of the seat bolts, lift the back of the seat, then pull straight back; a plastic flange on the front of the seat hooks under the tank, and so you have to pull it backwards to remove it.

    With the seat off, removing the battery is pretty easy. A rubber strap holds the battery down; unhook and remove it. Unscrew the lead wires and unhook them (negative first), then pull the battery out.

    Install a replacement battery by reversing these steps. Yamaha recommends charging a new battery before installing it.

    -solomoia

    Jul 07, 2009 | 2001 Yamaha TW 200

    2 Answers

    How 2 change a battery on a 1999 tdm 850


    Hello! I used to own a 1991 XTZ (Off road version of your TDM) And the battery if I remember is behind the right side panel, these are a push fit so be careful when pulling them off. Gently pull towards yourself one edge at a time, If not right side try left. You'll be investigating under your seat too as there should be a tool kit in your tail piece to help remove battery.
    Merry Christmas ans remember push the Blue FixYa button!
    Paul 'W'
    Onyer~EDson(:0)~[><

    Dec 10, 2008 | 1999 Yamaha TDM 850

    Not finding what you are looking for?
    Motorcycles Logo

    Related Topics:

    143 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Suzuki Experts

    yadayada
    yadayada

    Level 3 Expert

    75797 Answers

    Arnie Burke
    Arnie Burke

    Level 3 Expert

    4514 Answers

    Ed Nelson
    Ed Nelson

    Level 2 Expert

    149 Answers

    Are you a Suzuki Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...