Question about Husqvarna AE 430 Motorcycles

1 Answer

It had spark then nothing then its back again ?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 148 Answers

Hi,,check for any loose wires ,sounds like a loose connection somewhere.

Posted on Mar 23, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 1996 Yamaha Kodiak 400 with no spark


If you have another one try the ignition switch and the kill switch.

Jan 27, 2014 | Yamaha Motorcycles

1 Answer

Husqvarna 359 - No Spark


remove the side cover and then the small wire to the coil check for spark again if still no spark the coil is bad if you get spark back the problem is the switch or wiring

Oct 04, 2012 | Husqvarna Garden

1 Answer

I have a yamaha 400 it is running on one cyclinder i cleaned the carboter out and it ran good for a day it is doing it again i pulled the carboter off again cleaned it all out nothing wrong with it that i...


Replace both of your spark plug caps. They are available after market (NGK brand) for about $5 each. Simply unscrew the old ones off of the end of the wires and screw the new ones on. When a spark plug cap burns out the 5000 OHM resister the motorcycle will stop firing on that cylinder.

May 17, 2011 | 1981 Yamaha XS 400 Special

1 Answer

350 16" inc. chain saw want crank with new plug or starter fluid


Check for spark at the plug (gapped at 0.020"). If nothing, remove the left side case and starter--this exposes the ignition module. Check the pole gap with a thin business card for a gauge. Turn the flywheel until the magnets are under the module poles, insert the card into the gap, loosen the module screws and let the module contact the magnets. Tighten the screws, rotate the flywheel somewhat to release the card and recheck for spark. If still nothing, try removing the stop-switch wire from the module and try for spark again. If nothing again, replace the module. Install as above. Hope this helps!

Sep 21, 2010 | Husqvarna Chain Saw 20" Bar

1 Answer

Cant get it started was going now wont


Remove the spark plug and check for spark (gapped 0.020") which should be blue and snappy. If nothing, try a fresh plug. If still nothing, remove the cover to expose the flywheel and ignition module. Remove the stop switch wire from the module and try for spark again. If nothing again, replace the ignition module. Use a thin business card for a gap gauge between the flywheel magnets and the module poles. If the first test obtained good spark, pour a small amount of fuel mix into the plug hole and try for start. If it pops several times, then check the fuel filter, air cleaner, and muffler for plugging. Check the fuel line condition. Make sure the carburetor fasteners are tight. You may need to clean the carburetor inside and out with spray carburetor cleaner. Check the lower chamber diaphragm for flexibility and no holes or cracks. Hope some of this helps!

Aug 07, 2010 | McCulloch Garden

1 Answer

Poulon chain saw model 2175 no spark. What to check?


Remove the starter assembly and left side cover to expose the flywheel and ignition module after trying a new spark plug gapped at 0.020". Remove the ignition switch wire from the module and try for spark again--if still nothing, use a thin business card for a gap gauge between the flywheel magnets and the module poles. Loosen the mounting screws, let the module contact the magnets through the card, then tighten the screws. Try for spark again--if still nothing, replace the module. Use the above procedure to install the new part. Hope this helps!

Aug 05, 2010 | Poulan Garden

1 Answer

My chainsaw is not getting any fire


Remove the spark plug and check for snappy, blue spark. If nothing, try a new plug. If still nothing, remove the left side case to expose the flywheel and ignition module. Remove the wire that goes to the stop switch from the module and try for spark again. If still nothing, it's new module time. Use a thin business card to set the gap between the module and flywheel magnets. If the gap was excessive with the old module, resetting it may bring back spark. Hope this helps!

May 13, 2010 | Garden

1 Answer

Put new carb on 86 cr 80 ran fine 4 10 minutes then quit changed spark plug and gas still nothing. has spark dont know how hot also changed manifold appeared to be dry rotting still nothing. even attemped...


for any motorcycle to run you need three things. spark, fuel and compression. i see you've tried to get fuel and spark. if you have spark thats one down. dont pour fuel into cylinder. instead spray tiny bit of brakeclean or carb clean into spark plug hole. i have a feeling if you drained your gas after the carb clean the carb most likely sucked bad gas back up and might need cleaned again. ive seen it happen alot on ols bikes.

Jul 11, 2009 | 1993 Honda CBR 600 F(2)P

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

69 people viewed this question

Ask a Question

Usually answered in minutes!

Top Husqvarna Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

venugopal durairajan

Level 3 Expert

464 Answers

choprboz5

Level 2 Expert

196 Answers

Are you a Husqvarna Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...