Question about Honda GL 1100 Innerstate Gold Wing Motorcycles

1 Answer

What carb is the number three - GL 1100 Innerstate Gold Wing Honda Motorcycles

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Renaissance:

    An user who is expert in 3 categories / brands.

  • Honda Master
  • 1,508 Answers

With out the model its a bit hard to guess, as there are many engine combinations like a V4
but if it is a straight 4 cylnder , as you sit on the bike the left cylnder and carb is the first, counting across to the right the right hand is number 4

Posted on Mar 23, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1997 3cyl 25HP Evinrude outboard Would changing the carbs to 35HP carbs make this a 35HP motor?


Depends if the bore and stroke are the same, if they are not, adding larger jetted carbs can result in always running rich. The mixture would be incorrect for the amount of air the cylinders take in.

Feb 02, 2017 | Cars & Trucks

1 Answer

Johnson 70hp model number A J70TLESB it starts fine and revs up neutral; ok but was lacking speed unless the ckoke is held in.then just stopped, will start and rev up but die when put in gear


I had a Evinrude 70 with the same problem. The cause was a connecting rod that wasn't clipped on the carb linkages. It is just to the left of the automatic choke. Unless this little clip is in place, you are only operating on one carb. Operate the throttle and make sure all three carbs are moving.

Holding the choke in, overgasses that one carb that is working fine.

I have a picture on my computer at home. Let me know by way of COMMENT under my post if you want to see it.

Dec 15, 2016 | Cars & Trucks

1 Answer

How to adj the set screw on the bottom of carb on a 125 Suzuki 3wheeler


Greetings, Kenny. I'm guessing you are referring to the air/fuel adjustment *****. Most small engines will perform quite well with the ***** turned out one and a half to three turns. Seldom is this adjustment the reason for hard-starting or poor performance, however. To resolve carbureter problems you may remove the ***** from the carb and shoot some carb cleaner up into the carb. Turn the ***** clockwise for a lean mix; counter-clockwise for a richer mixture. Happy Three Wheelin'. Herb

Apr 29, 2015 | Suzuki Motorcycles

1 Answer

Bandit 1200


check ht leads have good connections, to plugs and coils, also 2 wires to coil which goes to number 1 cyl. hope it heps

Oct 30, 2013 | Motorcycles

1 Answer

Craftsman LTS 1500 lawn mower - model # 917.28903 started sounding funny while i was cutting VERY high grass. I turned it off immediately and it backfired as it shut off. Wouldn't restart. Waited til next...


I would check the big three first of all. Spark, compression and fuel. Sounds like you have spark and fuel. I would get a compression tester to check actual amount of compression. If all three of those things are good I would check valve lash. You will need make, model and serial number of engine. If you post these I can help find specs for you. Good luck.

I’m happy to assist further over the phone at https://www.6ya.com/expert/layne_0fccff498c319c32

Sep 14, 2013 | Craftsman 17.5 hp 42 in. Deck Lawn Tractor...

1 Answer

When syncing the carbs on a 1991 Honda CBR 600 F2 there are only three adjusting screws to adjust them but there are four carbs on the bike. So how am I to sync the carbs with only three screws?


There are only three adjusting screws because you are adjusting them to the fourth, if you could adjust all four the possibilities would be infinite.

Dec 17, 2012 | Motorcycles

1 Answer

I have an estate 2005 20hp ohv I/c v-twin model number 13AG618G706. It starts and runs fine until I Engage the blades. Once I do that it'll run fine at a really slow pace. If I hardly press on the...


carb carb carb rebuild rebuild rebuild but as always check spark and compressin on both sides if you only have spark on one side it will sound fine untill under load

Jul 12, 2012 | Briggs & Stratton Briggs Stratton Intek V...

1 Answer

GPZ 1000A1 1987 Fuel leaking into engine from number three Carb Tap not on PRIME. New genuine Kawasaki petrol tap repair kit fitted. has done this on two different sets of carbs ? Tried everything I know...


YOUR CARB FLOAT NEEDLE VALVE IS LEAKING. YOU WILL HAVE TO REMOVE CARBS AND CHECK. IT SOUNDS LIKE A NEEDLE VALVE IS DEFINETLY STUCK OR YOUR FLOAT IN THE CARB IS PUNCTURED

May 15, 2011 | kawasaki Ninja Zx7r Zx9r '94 To '04

2 Answers

My 2001 yamaha 125l ttr having a fuel issue.fuel sqirted in through air intake,bike runs,throtle respondsive,couple seconds only.maybe dismantle carb and blow out.appreciate any insight.thank you.


ALWAYS have a fire extinguisher on hand when working on carburetors. Drain the carburetor. There should be a screw on the lower side of the carb float bowl. Remove the screw then replace it after the fuel drains then remove the carburetor from the engine.

Remove the float bowl and soak the entire carb in denatured alcohol for 30 minutes. Now clean the entire carb with a spray carb cleaner from the auto parts store. Wear protective goggles to avoid getting spray in your eyes. Spray into all the little airways and fittings in the carb. Remove the "blue" items on the
carb and spray into the screw holes as well. Don't mess with #16 but if you must, be sure to count the number of turns and replace the same number of turns.

< < READ CLOSELY > >
Be sure to put all screws back in the same hole they came out of. IMPORTANT > do not tighten #8 and #12 adjusters down. Only screw these in until they LIGHTLY seat. Now turn each adjuster one and one half turns outward. Put the rest of the
carb back together, clean the air filter and install the carb. Let the float bowl fill then start the engine.
Please rate this answer. Thanks!

68dd110.gif

Nov 21, 2009 | 2002 Yamaha TT-R 125 L

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

39 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4988 Answers

yadayada
yadayada

Level 3 Expert

80407 Answers

bazzz7071
bazzz7071

Level 2 Expert

342 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...