Question about 2001 kawasaki ZX-9 R Ninja

1 Answer

Where is the mixture adjustment on my 01 zx9. is it in the frame above the left foot peg?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 148 Answers

Hi, above the left footpeg in the frame is for the idle,,,the mixture adjustment screws are on the carbs.

Posted on Mar 23, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Location of serial # on a yamaha bruin 350 atv.


all yammies I know have them under the left foot peg.

May 05, 2017 | ATVs

1 Answer

I want to switch the passenger foot peg. Can I remove just the peg or do I have to remove the peg and the brace attached to the frame? Couldn't figure out how to remove the bolt the existing peg...


You should be able to take just the footpeg off the support from the frame. It may not be a bolt but a pin with a circular clip on the other side.

Good Luck
steve

Jul 15, 2011 | 2005 Harley Davidson FLHRS - FLHRSI Road...

1 Answer

K I have a 2003 yamaha wr 250f i have noiced I tend toride with my rear brake on I don't mean to but how do I lower the rear brake lever down becuzi noticed it actually set up higher than the foot peg...


There is some form of adjustment between the foot lever and the mastercylinder. Just undo the locknuts and turn the adjusting rod and watch for the foot lever to lower, if it raises, turn the adjusting rod in the other direction. Don't forget to do the locknuts up when finished. NOTE: one nut is left hand thread and the other in right hand thread. most of the bikes I have ridden have the pedal above the footrest, but that is a personal preference.

Jun 28, 2011 | Yamaha WR 250 F Motorcycles

1 Answer

I have a 75 flh with the passenger peg mounted to the primary inspection cover.is this stock. if not where do they mount


Yes, this is where the passenger foot peg on the left side of the bike goes. There is an arm that clamps onto the round stub on the inspection cover and is afjustable to almost any angle. The right side foot peg support bolts to the end of the transmission and also has an adfustable arm that clamps onto a stub on it. Then the pegs go on the end of the arms. Go to this site and take a look . http://www.bikebandit.com/1975-harley-davidson-flh-1200/o/m770#sch171752 I'm pretty sure they didn't move the peg brackets to the seat tubes of the frame until 1977. If your bike has two holes in a welded-on tab on the rear of the down tubes behind the primary and the transmission, you can use the later model peg brackets. But, if your bike has no holes in the frame or the swingarm for passenger peg brackets, this is the only style you can use and stay original. You could fabricate and weld on tabs to later model peg brackets or use clamp on brackets and pegs.


Good Luck
Steve

Apr 03, 2011 | Harley Davidson FLHTCUI Electra Glide...

1 Answer

How do you take out the starter?Does the engine has to be taken off the frame?.


No, the engine does NOT have to come out of the frame.

First, disconnect the battery. Drain the primary cover, remove the shifter, foot peg, loosen the primary chain adjuster under the outer cover, whatever needs to be removed depending on your model Sportster to get the primary cover off.

From the right side of the bike, remove the exhaust system and whatever you need to remove to get the starter off. Disconnect the large battery cable and the single wire from the starter.

Back on the left side, there are two large bolts just above the clutch assembly, remove them. They may be different lengths so watch for that. Remove the starter.

Good Luck
Steve

Sep 14, 2010 | 2004 Harley Davidson XL 1200 C Sportster...

2 Answers

Will 1994 ZX9 fairings fit on a 1998 ZX9??


No... the 94 bike is a different design, also the frame is a complete new design on the 98

Mar 25, 2010 | 1998 kawasaki ZX-9R Ninja

1 Answer

Clutch cable broke at handle lever on 1979 harley davidson sporst


To change the clutch cable on you '79 Sporty, you'll have to take the outer primary cover off. To do this, you'll have to drain the oil from the primary, take the left side foot peg off, and loosen the primary chain adjuster on the bottom side of the primary. Loosen the locknut and use an allen wrench or hex key to screw the adjuster bolt downward.

If you need to know anything else, drop me a line at wd4ity@bellsouth.net

Then, remove the large "plug" towards the rear of the cover. Inside, you'll see something that looks like a nut but with no threads in it held in by a small spring. This the the lock nut, remove it. Below it is what looks like another nut with a slotted adjuster bolt sticking out. Remover the bolts from around the primary cover and break it loose from the engine. While turning the adjuster screw at the rear of the cover inward, remove the cover.

The cable connects to the cluch release mechanism. By turning the "link" downwards, you can disconnect it from the mechanism. Notice which way the "link" in attached to the release mechanism. Take the "link" off the end of the clutch cable.

Break the lock nut loose at the threaded cable adjuster on the outside of the case and screw the adjuster all the way out of the primary cover. Disconnect the cable at the handlebar lever and your cable is out.

Reinstall the new cable in the reverse order. When replacing the outer primary cover, make sure you use a new gasket on the cover as well as on the foot peg boss. The "foot peg boss gasket" is very important. You'll see an aluminum boss with a threaded rod sticking out of it that holds your left foot peg on. There is a round gasket that goes over this threaded rod and seals against the boss. If you leave this off, your bike will leak oil around this threaded rod when your foot peg goes on. Make sure you specifically ask for the "foot peg boss gasket" when you buy the new primary gasket. It's just a round gasket a bit larger than a quarter.

As you put the primary cover back on, there is a spring on the primary chain adjuster. Part of the spring is in the primary cover and the other part is in the engine. You'll see how it goes in. There is a large stud in that area that the outer primary cover slides up on. Adjust the tension on the primary chain by removing the "plug" at the top of the primary cover. You want 3/4" to 7/8" up and down play in the chain with the engine cold.

On the adjuster, as you're installing the outer cover, turn the ajuster screw back into the clutch release mechanism by turning the screw backwards. Once you have the outer primary cover completely installed, you must adjust the release mechanism. Adjust the screw inwards until you feel a resistance, then back the screw off about a 1/4 to 1/2 turn, insert the "lock nut" and spring, and install the "plug". Then, using the cable adjuster on the outside of the cover, adjust the cable. Add oil.

Oct 26, 2009 | 1979 Harley Davidson XLH 1000 Sportster

1 Answer

Carolina rudder does not work properly


Slider to which the pegs are attached is probably binding, take entire mechanism out (2 screws), and lubricate with silicone wax. If that doesn't work, replace sliders and pegs.

Apr 06, 2009 | Carolina Manufacturing Perception Carolina...

1 Answer

My MT-03 is vibrating an making a bit of a tattling sound


Hi mattandem

I have replied already to your other post... didn't see this one... not sure what the vibration through the peg could be caused by as they mount directly to the frame. The frame being a substantial structure to the bike means that the vibration is being created anywhere on the frame,and you are feeling it in your foot peg. The only thing that comes to mind is that perhaps one of the tank mounting rubbers is not seated properly, or inadvertently rolled away on the garage floor. This is what I would be checking for.

regards
robotek

Dec 06, 2008 | 2008 Yamaha MT-03

2 Answers

Closing


Lifting on the handle in the back is not all you do!  You first have to pull up on the latches at the handles, which pull the pegs just above the front wheels up and out of the hooks which are locking the two bars together in place.  The pulls on the handles are not obvious... the gray buttons adjust the height of the handles, but then there are black pieces that pull up toward the handles.  If this doesn't make any sense, try looking at the frame above those front wheels.  There are plastic hooks holding pegs which snuggly locks those two pieces of frame against one another.  Once those are released, THEN you pull on that handle in the back, and it should fold up.  Those same pegs need to latch to lock the stroller in its folded position.  And you need to play with the way the wheels are swiveled when you do so, or the unit won't free stand very well.  It is not a very user-friendly folding mechanism!

Apr 20, 2008 | Peg Perego Pliko Matic Umbrella Stroller

Not finding what you are looking for?
2001 kawasaki ZX-9 R Ninja Logo

177 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...