Question about 1983 Yamaha XS 400 L Maxim

1 Answer

Turn signal on one side dont work - 1983 Yamaha XS 400 L Maxim

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 148 Answers

Sounds like a blown globe,,check and replace,,if the globe is ok,you need to inspect the wires from that indicator all the way,for loose connection,or frayed and shorting out somewhere.

Posted on Mar 23, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 1992 GMC Yukon 4x4 blazer just had it in the shop when it came out the lights are all messed up. headlights work high and low. driver side turn signal dont work , passenger side turn signal don't...


If those lights all worked properly before the shop "fixed" it, take it back to the shop and ask them to make it right. If they are reputable, they will correct the problem(s). If not, think Small Claims Court.

Oct 08, 2013 | GMC Cars & Trucks

1 Answer

Turn signal dont work


1st if both sides dont work check the fuse
if one side dont work check that all the bulbs are good
if every thing checks out good most likey the turn single switch must be replaced

Oct 31, 2012 | Cars & Trucks

1 Answer

My saturn signal light work sometime than go off if it the flasher please tell me there it is in my car


IF TURN SIGNAL LIGHT DONT WORK SOME TIMES.CHECK FOR BLOWED OR LOOSE FUSE.CHECK TURN SIGNAL BULBS AND CHECK BULB SOCKETS FOR CORROSION.CHECK TURN SIGNAL FOR BAD GROUND.USE JUMPER WIRE BETWEEN GROUND SIDE OF THE TURN SIGNAL BULBS AND A GOOD CHASIS GROUND.IF ALL IS GOOD TURN SIGNAL SWITCH IS BAD OR FLASHERS GOING BAD.TURN SIGNAL FLASHER LOCATED ON CENTER CONSOLE SIDE PANEL GRASP THE FLASHER UNIT AND DETACH IT FROM THE FUSE BOX.IF YOU HAVE EARLY MODEL VECHICLE FLASHER UNIT LOCATED AT THE FRONT OF THE FUSE BLOCK.

Aug 23, 2011 | Saturn LS Cars & Trucks

2 Answers

Turn signals dont flash on 95 firebird formula


There are dual elements bulb and single element bulb.

You need to see is there two contacts inside the socket.

If you accidentally put a single contact bulb into dual contact socket......it will cause this problem.

Check it out.


Jul 14, 2009 | 1996 Pontiac Firebird

3 Answers

1997 dodge avenger turn signal probs and location


replace the turn signal switch it self, mine did the same thing with the left turn signal, put in fuse and it will continue to flash... went to junk yard pulled one out of a 97 avenger just like mine, swapped them out and now it works fine. looked to be like some corrosion... to repace: 3 screws under columb, 2 screws on side of signal switch (black plastic side). unplug and replace

Mar 20, 2009 | 1997 Dodge Avenger

1 Answer

Turn signals and back up lights dont work, bulbs and fuses good. Blinker lights only work in dash when emergency flashers are on.


Test the circuit board wires on the back side of your taillights where the bulbs go in to see if power is going there with the blinker on, if yes replace the circuit board (quite common with these trucks). If there is no power back there check your flasher relays for each turn signal, assuming they dont click off and on when you tip the turn lever. if all else fails, head for the multifunction switch behind your steering wheel inside the column that your turn signal/wiper/cruise control lever is connected to.

Mar 06, 2009 | 1991 Chevrolet C1500

3 Answers

Turning signals dont blink


Problem is the Turn Signal "FLASHER" unit, 1.Turn on Emergency FLASHERS 2. Go under Dash while they are on Listen -for Clicking sound then feel for it 3. Should Be a Silver Round Unit About as Big IN ROUND as Half dollar coin 4. ok now Look Around for the SAME EXACT Thing Clipped onto Something Under dash At Driver side Usually Between Steering wheel and Center HUMP in Floor, 5. once you find it Take OUT the first One you Found Emergency FLASHER) and 6. Put it In Place of Turn Signal Flasher, 7. Turn off Emergency Flashers- Turn Key in "ON" Position but don't start then Try Turn Signals. Yaaaa !!!! they work ?? LoL hopefully this Does the trick, if they work Buy new one and Replace Always Use NEW For TURN Signals as they are used Much More than Emergency Flashers. Hope this is Good Instructions For you and Helps you Solve The Problem, Please DONT Forget to RATE ME Thank you Rejakwilson@aol.com

Jan 18, 2009 | 1986 Oldsmobile Cutlass Supreme

Not finding what you are looking for?

Open Questions:

See all 1983 Yamaha XS 400 L Maxim Questions

1983 Yamaha XS 400 L Maxim Logo

Related Topics:

92 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Experts

dhnguyen

Level 2 Expert

281 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1144 Answers

Tony

Level 3 Expert

2600 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...