Question about kawasaki Ninja Zx7r Zx9r '94 To '04

1 Answer

I just rebuilt my zx7 and i have no pressure on the clutch?

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has answered 20 questions.

  • Expert
  • 148 Answers

Hi,,the clutch needs bleeding

Posted on Mar 23, 2011


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How do you bleed a slave cylinder when there is no clutch? Rebuilt all components. Found a leak in hydraulic system of clutch release cylinder. No pedal at all. What do I do?

how did you find a leak in the clutch if there is none should have went to a mechanic in the first place sounds like .

Mar 11, 2015 | 1993 Mazda MX-3

1 Answer

1995 kawasaki zx7r

Side stand down or faulty side stand cut out switch ?

Jul 26, 2014 | 1995 kawasaki ZXR 750

1 Answer

Kawasaki zx7

carb may have meetering jet cloged if bike will run on choke only then meetering is faulted

Mar 15, 2014 | Motorcycles

1 Answer

Won;t start while clutch pressed but will push start

The clutch master cylinder must have gone out, the seals in it have failed. The clutch master cylinder (next to the brake master cylinder) gives you hydraulic pressure so the clutch pedal can operate the clutch.
You can buy a new clutch master, a rebuilt unit, or yours can be rebuilt with new seals. Save time and money and buy a rebuilt or remanufactured unit. Once installed, you bleed the system down at the clutch slave cylinder, mounted on the transaxle.

Jul 15, 2013 | 1989 Honda Prelude

1 Answer

Zx7 running weird tach flicking up and down

Sounds like an engine misfire, most likely due to a spark plug connector insulator leaking to the cylinder head.

Jun 27, 2017 | 1991 kawasaki ZXR 750

1 Answer

Just had the clutch rebuilt on my 1985 ford f-150 pickup (manual trans.) Truck has 65,000 original miles. I only drove the truck a few miles since the clutch was rebuilt and only to plow my road a few...

Ok fall speeds but does not walk well could be that when you built and installed the disc backwards clucht stay then you have pressure on the pedal come marches but does not walk or stay glued the bearing and you hold the clucht also why not walks

Mar 24, 2010 | 1985 Ford F150

1 Answer

I just had transmission rebuilt and i was putting in slave cylinder and bleed clutch am not getting any pressure to change gear

Make sure that there isn't any air in the system. Also check for any leaks. Was the pressure plate and clutch replaced?

Mar 09, 2010 | 1992 Chevrolet S-10

1 Answer

No clutch pressure

Its more than likley that you have an air lock in the clutch fluid ,try bleeding it again very carefully

Apr 26, 2009 | Yamaha FJ 1100 Motorcycles

Not finding what you are looking for?
kawasaki Ninja Zx7r Zx9r '94 To '04 Logo

Related Topics:

131 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4899 Answers


Level 3 Expert

79865 Answers


Level 2 Expert

342 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides