Question about 1995 Yamaha FZR 600

1 Answer

'96 fzr 600. Bile has not been started in two years. I have removed the carbs but before i clean them, any advice? I've removed the tank, and cleaned it already, now the carbs. I've been maintaining motorcycles for years but never tackled these carbs.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 36 Answers

Do one at a time use proper carb cleaner, lay the bits out carefull on a clean bench or table then you can rebuild it from the ones you have left together.

Posted on Mar 21, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need to clean out my pistons


Hi, Jeff I hope your talking about carburetor pistons/slides and not engine pistons, if your bike has been sitting idle for months or years and you did not do any pre-storage maintenance I feel your pain it will probably have a dead battery and not want to start or if it starts it will idle and run poorly, here are the following steps necessary to complete in order to get your bike back to an acceptable running condition.
1. If your battery was 3 years or older when you last had the bike running you should replace it.
2. If you believe your battery might still be serviceable remove it from the bike and put it on a 1 or 2 amp trickle charger for 24 hours. If it is the old lead acid type with visible cells and acid levels fill each cell to the top line with distilled water and replace the caps, run the vent tube into a plastic or styrofoam cup, any cells that are cloudy/milky replace the battery.
3. After charging remove the leads and let the battery sit for a couple of hours then check the battery voltage with a volt meter, you should have 12.5 volts or better, any readings in the 11 volt range you need to do a proper load test on the battery and replace as necessary, any readings in the 10 volt range you have a dead cell and replace the battery.
4. Drain and flush fuel tank, google " how to clean a motorcycle gas tank" find a couple forums to view the different options available.
5. Remove your air cleaner and clean and re-oil per Mfg. specifications.
6. Remove the carburetor, disassemble and decontaminate with a carb dip or if you have EFI remove injectors and clean with carb spray and compressed air
7. Remove fuel valve and filter disassemble and clean as necessary, remove fuel lines and replace with new ones.
8. Replace spark plug with a new one and check for spark.
For more information about your issue and valuable "FREE" downloads that you will need please visit the websites below. Good luck and have a nice day.
Complete Carb Rebuild Kit The FZR Forum
step by step fzr600 carburetor rebuild
https://www.tradebit.com/filedetail.php/269137237-yamaha-fzr600-1989-1999-factory-service-repair-manual
OEM parts for Yamaha
http://www.fzrarchives.com/fzr600/600_manual/1999fzr600r.pdf

Mar 04, 2013 | 1990 Yamaha FZR 600

1 Answer

1991 yamaha fzr 1000 it has sat for 2 years. i bout it as a project bike. i have drained the gas tank and cleaned it. when i try to start it it tries but wont start. i dont know where else to turn or what...


Hi, Rossi_thomas if your bike has been sitting idle for months or years and you did not do any pre-storage maintenance I feel your pain it will probably have a dead battery and not want to start or if it starts it will idle and run poorly, here are the following steps necessary to complete in order to get your bike back to an acceptable running condition.
1. If your battery was 2-3 years old when you last had the bike running you should replace it.
2. If you believe your battery might still be serviceable remove it from the bike and put it on a 1 or 2 amp trickle charger for 24 hours. If it is the old lead acid type with visible cells and acid levels fill each cell to the top line with distilled water and replace the caps, run the vent tube into a plastic or styrofoam cup, any cells that are cloudy/milky replace the battery.
3. After charging remove the leads and let the battery sit for a couple of hours then check the battery voltage with a volt meter, you should have 12.5 volts or better, any readings in the 11 volt range you need to do a proper load test on the battery and replace as necessary, any readings in the 10 volt range you have a dead cell and replace the battery.
4. Drain and flush fuel tank, google " how to clean a motorcycle gas tank" find a couple forums to view the different options available.
5. Remove your air cleaner and clean and re-oil per Mfg. specifications.
6. Remove the carburetor, disassemble and decontaminate with a carb dip or if you have EFI remove injectors and clean with carb spray and compressed air
7. Remove fuel valve and filter disassemble and clean as necessary, remove fuel lines and replace with new ones.
8. Replace spark plug with a new one and check for spark.
For more information about your issue and valuable "FREE" downloads that you will need please click on the websites below. Good luck and have a nice day.
https://answers.yahoo.com/question/index?qid=20080315213436AALQvHk
FZR Won Start The FZR Forum
http://fzronline.com/wiki/lib/exe/fetch.php?media=ebook_library:fzr1000_service_manual_89_90.pdf
OEM parts for Yamaha
Yamaha FZR 1000 1991 1993 Manual zip

Jul 30, 2011 | 1995 Yamaha FZR 600

1 Answer

Cleaning the carbs on a '96 fzr 600 that hasn't run in two years. Any advice? I'm no stranger to motorcycles or maintaining them but this is the first times i've tackled these carbs. I have removed them...


write note on where the air screws are adjusted before pulling them out.
If you see something you may confuse later take a photo, like vacumn hoses, overflow hoses, fuel hose.
The slides may look a little worn, this is usually not a problem, apart for obvious cracks, then its replace all four
dont touch the adjustable syncronizing screws, that lift all the slides together.
dont mix parts between carbs.
When putting them back on
Check the inlet rubbers and install them tight
Make certain the throttle snaps all the way back before starting the bike.
And of course work in a clean area, and remember its fuel and will burn when it can, so no ignition sources.

Mar 21, 2011 | 1995 Yamaha FZR 600

1 Answer

I have fzr 600 foxeye but i have not started in over six mouths i have drained the tank put fresh fuel in and fully charger battery fuel pump is working but no fuel flow or fuel pipe is bone dry


Hi, M_dean09 if your bike has been sitting idle for months or years and you did not do any pre-storage maintenance I feel your pain it will probably have a dead battery and not want to start or if it starts it will idle and run poorly, here are the following steps necessary to complete in order to get your bike back to an acceptable running condition.
1. If your battery was 2-3 years old when you last had the bike running you should replace it.
2. If you believe your battery might still be serviceable remove it from the bike and put it on a 1 or 2 amp trickle charger for 24 hours. If it is the old lead acid type with visible cells and acid levels fill each cell to the top line with distilled water and replace the caps, run the vent tube into a plastic or styrofoam cup, any cells that are cloudy/milky replace the battery.
3. After charging remove the leads and let the battery sit for a couple of hours then check the battery voltage with a volt meter, you should have 12.5 volts or better, any readings in the 11 volt range you need to do a proper load test on the battery and replace as necessary, any readings in the 10 volt range you have a dead cell and replace the battery.
4. Drain and flush fuel tank, google " how to clean a motorcycle gas tank" find a couple forums to view the different options available.
5. Remove your air cleaner and clean and re-oil per Mfg. specifications.
6. Remove the carburetor, disassemble and decontaminate with a carb dip or if you have EFI remove injectors and clean with carb spray and compressed air
7. Remove fuel valve and filter disassemble and clean as necessary, remove fuel lines and replace with new ones.
8. Replace spark plug with a new one and check for spark.
For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have a nice day.
http://en.allexperts.com/q/Motorcycle-Repair-837/98-Yamaha-FZR-600.htm
https://www.tradebit.com/filedetail.php/2864660-yamaha-fzr-600-service-repair-manual-pdf
OEM parts for Yamaha
http://mybikemanuals.com/yamaha/yamaha-fz-owners-manuals

Aug 27, 2010 | Yamaha FZR 600 Motorcycles

2 Answers

Bike sat for awhile, runs but doesnt idle very good. cuts out


I would remove and clean the sparkplugs - sounds like one may be fouled.

Aug 18, 2009 | 1994 Yamaha FZR 600

1 Answer

1993 fzr sitting for 5 years ?? Where do i start?


Remove the water trap bowl at the bottom of the petcock, (gas valve). Is there any water or trash in the bowl? (not all bikes have a water trap bowl). Install an in-line fuel filter. Use premium gas. You will need to clean the built up varnish from the evaporated gas out of the carbs.

FOR EACH CARB > Remove the float bowl and clean the entire carb with a spray carb cleaner from the auto parts store. Wear protective goggles to avoid getting spray in your eyes. Spray into all the little airways and fittings in the carb. Remove the idle screw and the air screw on the outside throat of the carb and spray into the screw holes as well.
< < READ CLOSELY > >
Be sure to put these two screws back in the same hole they came out of. IMPORTANT > do not tighten these two screws down. Only screw these in until they LIGHTLY seat. Now turn each screw one and one half turns outward. Put the rest of the
carb back together, clean the air filter and install the carb. Let the float bowl fill then start the engine.

I strongly suggest you to let the shop take care of the carbs. Cleaning can be a nightmare times four and doing the balancing and sync of the carbs sounds easier than it is. If you do the carb work yourself, then be sure you have a fire extinguisher at hand. I am serious about that.

Please rate this solution. Thanks!

Apr 23, 2009 | 1991 Yamaha FZR 600

1 Answer

Bike won't start 92 yamaha fzr 600


Sounds like the plugs are fouled out, I would pull them and make sure they're about the color of a paper bag. If they're all sooty and wet you most likely have a rich condition. I would take the carbs out and clean everything and pop in a new set of plugs. I have a 87 Fz600 that was acting up until I cleaned the carbs.

Apr 20, 2009 | 1994 Yamaha FZR 600

4 Answers

My 1991 yamaha fzr 600 has been sitting for three years same gas and oil and filters. it starts with a full choke but when you give it any thorottle it bogs out and dies


Any water in the gas? Remove the water trap bowl at the bottom of the petcock, (gas valve). Any water or trash in the bowl? ( not all bikes have a water trap bowl ). Drain all the old gas from the tank. Install an in-line fuel filter. You will need to clean the built up varnish from the evaporated gas out of the carbs.

FOR EACH carb > Remove the float bowl and clean the entire
carb with a spray carb cleaner from the auto parts store. Wear protective goggles to avoid getting spray in your eyes. Spray all the little airways and fittings in the carb. Remove the two screws on the outside throat of the carb and spray into the screw holes as well.
< < READ CLOSELY > >
Be sure to put these two screws back in the same hole they came out of. IMPORTANT > do not tighten these two screws down. Only screw these in until they LIGHTLY seat. Now turn each screw one and one half turns outward. Put the rest of the
carb back together, clean the air filter and install the carb. Let the float bowl fill then start the engine. Balance and sync the carbs.

I strongly suggest you to let the shop take care of the carbs. Cleaning can be a nightmare times four and doing the balancing and sync of the carbs sounds easier than it is. If you do the carb work then be sure you have a fire extinguisher at hand. I am serious about that.

Please rate this solution. Thanks!

Mar 29, 2009 | 1991 Yamaha FZR 600

1 Answer

My 1991 yamaha fzr 600 wont start


how long did you let it sit for with gas in the carbs, you may have clogged up your jets. after awile gas will break down and turn into varnish, if your bike trys to push the varnish through the system it will clog the jets. try to take off your seat then remove your plastic over the gas tank. remove the gas tank and you will see four bowls *silver ones right next to where the gas tank is on the carbs*. your bowls are in sets of two. there are drain screws on the bowls to remove the gas inside. remove the 16 screws holding the bowl onto the carb. *4 on each* inside you will see your floats and jets. carefully loosen the jets with a screw driver then finish unscrewing them by hand, they are brass and very soft. you should be able to hold up the jets to the light and see a small pin hole. if not get some carb cleaner and give them a squirt and blow them out. do not try to use anything to clean them out, they are very very sensitive and one knick will change the jet. after that i would spray some carb cleaner up the jet holes and try to clean them out also. if you have a compressor it would be wise to use that to blow out the gunk from the jet holes as well. after you run threw all 8 jets put them back together and see how it goes, if nothing you may have to check the jets again and if clogged again your carbs are gunked up and will need to be cleaned

Feb 11, 2009 | 1991 Yamaha FZR 600

1 Answer

My FZR 600 is acting up and backfires


I have had several bikes in my time. and keeping the carbs syncranized is very important. Did you put aftermarket pipes on it? try rejeting the carbs up 2+mm that may help the fuel air ratio?

Feb 01, 2009 | 1988 Yamaha XJ 600

Not finding what you are looking for?
1995 Yamaha FZR 600 Logo

Related Topics:

147 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Experts

dhnguyen

Level 2 Expert

281 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1144 Answers

Tony

Level 3 Expert

2600 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...