Question about 2006 Honda VT 750 Shadow

1 Answer

Replacing front right turn signal got the bike today made a tight turn and dropped cracking the right turn signal need to replace the whole housing. It looks like I have to take the headlight apart to get to the wiring need help.

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Master
  • 1,591 Answers

Yes, you need to remove the headlamp, the wiring is behind there

Posted on Mar 21, 2011

  • Norman Skinner
    Norman Skinner Mar 21, 2011

    there are a few screws around the rim, they allow removal of the headlamp. there is a bolt that holds the turn lamp leg. the wire just unplugs and the whole turn assembly comes off. You can then replace the entire turn assembly.



1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I have a 2002 Chevrolet suburban all my light's are not right turn on the signals they flash fast hit break the break lights dim every light on the back blinks when the signal is on help.

A fast signal is telling you that a bulb is not working. The unit is set up on amount of resistance that sets the speed. Most likely it is the rear light housing board is cracked. Remove the rear light and open the panel from the back. If this is the problem replace the whole fixture. Note very expensive on Amazon.

Apr 17, 2015 | 2002 Chevrolet Suburban

1 Answer

How do I replace front turn signal bulb

you have to remove the whole housing to change it

Mar 09, 2015 | 2003 Ford Taurus

1 Answer

Rear Turn signal is not working

Aren't your brake lights and turn signal lights on the same bulb, same filament? Recheck the bulb in the rear, as the rapid blinking is an indication of a burnt out bulb. If the bulb is the correct one and is good, check the connector and socket at the housing for a loose or poor connection.

May 26, 2012 | Dodge Durango Cars & Trucks

2 Answers

Rear turn signal is not working

did the housing come with new sockets? if not may be a bad socket or bad bulb.could even have a bulb in wrong.

May 26, 2012 | 2003 Dodge Durango

1 Answer

I have a 2004 Honda VTX 1300C. As I was riding today I noticed the left front turn singnal was loose. I tried to located the problem but could not. I took off the front light bar (stock bar) and all...

If the rubber mounting boot (turn signal stem) is sold separately from the turn signal , a new turn signal stem should fix the problem. If the turn signal stem is designed to be part of the assembly and does not separate , you may have to replace the whole turn signal assembly. The problem with Honda turn signal stems is the metal tab that bolts the turn signal assembly to the bike gets loose and the turn signal falls off. Your only other option would be to take the signal off and try to inject some epoxy or glue into the slot or figure out a way to fix the tab in place (so the signal doe not come off). Unfortunately , even if you replace the assembly it does not mean that some one brushing up against the turn signal (by accident) will not loosen up the new one, creating the problem all over again. You should be able to easily fix this your self with new parts and maybe save some money if you can solve the loose mount tab issue.

Nov 09, 2010 | 2004 Honda VTX 1300

1 Answer

Replace front right turn signal bulb

I replaced the front right turn signal on my 2005 Pontiac Montana by reaching up from underneath. I tried removing the battery but the opening from above was too small. I was able to pull the ground effects open enough to get my arm in. When you reach the bulb holder feel for two wings on the bulb socket and give the whole socket a quarter turn to and it will release. The wires are long enough so the entire bulb holder will drop down below the vehicle so you can easily replace the bulb.
Reverse the step to put it back in. You will not be able to see what you are doing so I had someone guide me by watching from above. Took less than 10 minutes once I decided to change the bulb from the bottom. I did not need to jack the vehicle up or use ramps.

Jun 14, 2010 | 2005 Pontiac Montana SV6

2 Answers

Need replace turn signal bulb


Aug 24, 2009 | 1996 Chevrolet Cavalier

2 Answers

Front right turn signal

i had a bad socket that was my problem on mine.

Dec 10, 2008 | 2000 Oldsmobile Intrigue

1 Answer

Turn signals

and before that they worked great with the old battery. This new battery is from the HD shop and now they don't work whats so ever. At first when I turned them on they were flashing like they were on crack. Now today they don't come on at might want to change the turn signal relay sounds like it's going out on you the dealer should have one  if not you might can get it  crossrefferenced at napa or autozone parts store you'll need the  part # off the old one tho. I don't know what model Buell you have but on the 12R the signal flasher is mounted under the fairing on the right side of the bike.,,

Nov 10, 2008 | 2004 Buell Firebolt XB9R

Not finding what you are looking for?
2006 Honda VT 750 Shadow Logo

90 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4988 Answers


Level 3 Expert

80531 Answers


Level 2 Expert

342 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides