Question about 1997 Yamaha Royal Star XVZ 1300 A

1 Answer

How to replace clutch slave cylender - 1997 Yamaha Royal Star XVZ 1300 A

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

  • Yamaha Expert
  • 191 Answers

If you go to www.venturers.org their tech library shows how to replace the stator on the Venture...the steps removing the middle gear case cover (behind which lies the slave) are in the write up....great site!

Posted on Mar 21, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Is there a clutch ajustment


no clutch slave cylender inside transmission it is hydraylic check your clutch master cylender under you hood for full or empty level if mt most likely clutch slave is leaking car will have to remove transmission to reapair costly around $1000.

Apr 05, 2014 | 2005 Scion xA

1 Answer

Cluth wont pump up no pressure


It sounds to me like they can't get the hydraulic clutch to build up pressure. Without pressure, the clutch will not engage. It's a very simple system, consisting of two major parts. The clutch master cylinder and clutch slave cylinder. Replacing both of them (recommended) would get you a good clutch pedal again. This is assuming, of course, the clutch installation was done properly with no problems.

Nov 01, 2012 | Honda Motorcycles

1 Answer

I replaced my master cylinder and my slave cylinder also bled the system and i still have no pressure in my clutch it drops to the floor


i just had that problem with my truck does yours have a slave cylender on the shaft of transmission

Aug 01, 2012 | 1986 Ford F150 SuperCab

1 Answer

No clutch pedal


Did you try bleeding it?
The ones I am familiar with, the slave cylinder is bolted onto the side of the bell housing at the point where your clutch lever sticks out.

Nov 25, 2011 | 2000 Saturn SL

1 Answer

The clutch is engaging as soon as you let off the pedal. Sometimes I have to turn car off to make it go into 1st.


you need to bleed your slave cylender, and make sure its toped off on fuel, this will solve your problem... there should be a bleed screw on the slave cylender. hope this helps

Dec 03, 2010 | Saturn SL Cars & Trucks

1 Answer

The clutch will not disengage i have replaced the slave cylender but it will not turn over


Did you bleed the system after replacing the slave cylinder? The air has to be bled from the line. DOT 3 brake fluid should be in the clutch master cylinder. Bleed it till all the air bubbles are out.

If it is not engaging the starter check that the switch on the clutch pedal is being contacted when the clutch pedal is depressed.

Dec 21, 2009 | 1997 Jeep Cherokee

1 Answer

Clutch master cylender keeps letting go, i guesst


the slave cylinder is your problem it throws out you throw out bearing.if leaking its a problem need to change.

Nov 25, 2009 | Computers & Internet

1 Answer

1993 240 nissan clutch pedal acts like it has no fluid


Check if the slave cylinder is being activated by the operation of the master cylinder (also ensure no fluid leaks are present).
If slave cylinder not moved, you still have a faulty master cylinder or slave cylinder - or the hydraulic system still has air.

If the slave cylinder is operating normally and there is still no return pressure from the clutch pressure plate, you have a faulty pressure plate or throughout lever mechanism.

Aug 12, 2009 | 1993 Nissan 240SX

1 Answer

Clutch peddle will not mash. we replaced clutch, presser plate, throwout bearing and master cylender and hose to slave cylender and clutch peddle won't mash you can take slave cylender loose fro...


when you bleed the system you need to force fluid from the slave cylinder up threw the master cylinder . this is proper way to bleed clutch system.

Jul 02, 2009 | 2003 Hyundai Santa Fe

1 Answer

Car shifts when not running, however once started gears won't shift....


Clutch isn't being released when pedel is pressed in. you need to either bleed the clutch, or adjust the clutch.You may have a pitted slave cylender. this means that fluid is passing around the piston in the slave cylender. if so you need to rebuild or replace the slave cylender. there may be other reasons too but these are some of the most common reasons

Apr 22, 2009 | 1997 Mazda MX-5 Miata

Not finding what you are looking for?
1997 Yamaha Royal Star XVZ 1300 A Logo

333 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Experts

dhnguyen

Level 2 Expert

281 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1144 Answers

Tony

Level 3 Expert

2600 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...