Question about 2008 Husqvarna WR 250

Open Question

Amount of fork oil in a wr250 2009 model - 2008 Husqvarna WR 250

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the correct amount of fork oil for a honda ntv 650 1993


J model 405cc
k,M and P models 466cc
S and T models 482cc

Oil level, measured from the top of the fork tube with the fork spring removed and the leg fully compressed..

J model 182mm
K,M and P models 123mm
S and T models 106mm

Oil type is stated as ATF

I guess that your bike is either an S or T model
Read more: http://www.visordown.com/forum/workshop/honda-ntv650-fork-oil/239264.html#ixzz3fdqFRRuc

I found this on a form on the internet. I hope this helps

Jul 11, 2015 | Honda Deauville NTV 650 Motorcycles

1 Answer

Standard amount of fork oil for Honda xrm 125, what is best 2t or fork oil, my front fork is so bumpy


The fork oil does not have anything to do with the kind of engine do you have, 2t or 4t. Doesn't matter.
You need to replace the fork oil, you need to know the year of the fork. means, you need to know if it's a bladder or non bladder fork.
oil height of the bladder fork is approx. 70mm, non bladder forks run about 100mm oil level.
oil amount is about 530-600cc per leg

Dec 11, 2014 | 2014 Honda CRF 125F

1 Answer

How to replace fork seals 2007 fatboy


To replace the front fork oil first support the motorcycle so the front end is off the floor and the forks are fully extended. Remember that the FLSTC and FLSTF models have a preloaded fork spring and that the fork tube plug is under spring pressure.Then you remove the fork tube caps. And then you drain the fork oil. ON FXSTD models, your remove the drain screws and washers from each fork and drain the fork oil this way. ON ALL MODELS EXCEPT the FXSTD, remove and discard the drain screws and washers from each fork and drain the fork oil and then you install new drain screws and washers. ON FXSTD models, apply LOCTITE THREADLOCKER 243 (blue) to the drain screws and tighten them to 12-18 inlbs (1.4-2.0 Nm). ON ALL MODELS EXCEPT FXSTD, tighten the drain screws to 52-78 in-lbs (5.9-8.9 Nm).THEN fill the fork with Harley-Davidson TYPE E FORK OIL (Part No. HD-99884-80).Either by installing oz or cc's of fluid if the forks were left in the frame or by measuring the amount of oil in the tubes in inches or mm if the forks were removed from the frame and disassembled. In the latter case the oil level is measured from the top of the fork tube with the spring removed and the fork fully compressed.

MODELs FLSTC, FLSTN use 13.4 OZ 395 cc4.41 inches 112.0 mm
MODEL FLSTF uses 13.4 OZ 397 cc5.04 inches128.0 mm
MODELs FXST, FXSTB, FXSTC use 12.5 OZ370 cc 6.69 inches170.0 mm
MODEL FXSTD uses 11.6 OZ343 cc 7.48 inches190.0 mm

FINALLY tighten the fork tube caps to 40-60 ft-lbs (54.2-81.3 Nm).

Jul 10, 2014 | 1993 Harley Davidson FLSTF Fat boy

1 Answer

How much oil in the front forks


2004 Touring Fork Oil Requirements

FORK MODEL TYPE and AMOUNT in OZ. ML IN. MM

Left FORK - All models except Road KingCartridge10.0 oz 295ML 4.21INCH 107mm

Road King Conventional 11.1oz 328ml 5.24inch 133mm



Right All modelsConventional11.1 oz 328ml 5.24inch 133mm



WARNING

Fork oil level in cartridge type forks is carefully measured from top of tube after pumping damper rod. Anydeviation from instructions can result in incorrect amount of fork oil. Incorrect amount of fork oil can adversely affect handling and lead to loss of vehicle control, which could result in death or serious injury.

Apr 14, 2014 | 2004 Harley Davidson FLHTCUI Electra Glide...

1 Answer

How much fork oil is required in the front forks of a 2000 suzuki 800 intruder and how do you measure if you put too much in. The guy at cycle gear where I bought the fork oil said to top it off or fill...


Hi, all model VS 800 from1992-2000 take the same amount of oil in the front forks, using 10 weight fork oil measure into a clean measuring device or mark the side of the oil bottle 413 mls, pour this caerfully into 1 fork, and the same amount into the other fork, 413/413 cm (3)

May 09, 2011 | 2000 Suzuki VS 800 Intruder

1 Answer

The front forks go down to far on my fxst 2004 nightrain


If you are saying that your front suspension is too soft, you can change the fork oil in the front forks to a heavier viscosity. I think Harley recommends Type E fork oil. I've found that PJB 30 wt. fork oil works best for me.

Since I'm not familiar with the newer forks, I'll have to recommend that you ask the dealer how to drain and refill the forks and how much oil to put back in them. There are usually two amounts of oil to put in the forks. One amount is a "dry" amount to add when you disassemble the forks and then refill them. The "wet" amount is for when you simply drain the forks and then refill them. Naturally, the "wet" amount will be less than the "dry" amount.

Sorry I couldn't give you more information but my expertise is the earlier model Harley bikes.

Good Luck
Steve

Jan 05, 2011 | 2004 Harley Davidson FXSTB - FXSTBI Night...

1 Answer

2003 CR 125 R: how much oil do the forks take?...


you will have to check your owners manual or shop service manual, each model has a specific weight and amount used in each fork,there is no one measured amount for all motorcycles.
The question you should ask is how much fork oil does my ( yr,,make,model ) take>

May 03, 2010 | Motorcycles

2 Answers

I have a harley davidson XL883H and need to know what the fron fork oil level should be when the forks are fully extended?


Remove the small plugs at the bottom of each fork slider and drain the forks. Do this by working the forks up and down until the forks are empty. Then, refill the forks with the proper amount of oil. Since you are not disassembling the forks and cleaning them out, you should use the "wet" measure of oil instead of the "dry" measurement.

Since you didn't tell me exactly what year model 883 you have, if the fork tubes are 39mm tubes (measure the top tube) use the following amount of oil. I use 30 wt. fork oil. If this is too stiff, drop down to 20 weight.

883 Hugger --- 10.7 ounces
all others --- 9.0 ounces

That's the only ones I have information for at this time.

Apr 12, 2010 | 2006 Harley Davidson XL 883 Sportster

1 Answer

Amount of fork oil for a XR 250 1985 model with 10 weight oil


13.4 ounces in each one. Or, with the fork spring removed and the forks compressed all the way, the oil level should be 150 mm (5.91") from the top of the fork tube.

Nov 09, 2009 | 1985 Honda XR 250 R

1 Answer

Fork oil capacity


medium fork oil - 150 mls in each leg

Nov 01, 2009 | 2005 Yamaha Ybr 125

Not finding what you are looking for?
2008 Husqvarna WR 250 Logo

Related Topics:

346 people viewed this question

Ask a Question

Usually answered in minutes!

Top Husqvarna Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4535 Answers

choprboz5

Level 2 Expert

196 Answers

Joseph Hoffmann

Level 3 Expert

1702 Answers

Are you a Husqvarna Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...