Question about 2008 Suzuki Boulevard

1 Answer

No power to the tail light, horn, tac ometer, speed ometer turn signal...tell me whats wrong

Posted by on

  • rzman
    rzman Mar 19, 2011

    have you checked the fuses?


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert that hasĀ over 500 points.


    An expert who has written 50 answers of more than 400 characters.

  • Suzuki Expert
  • 191 Answers

Typically your Signal fuse supplies all the above mentioned items....go to your main fuse box and check for the Signal fuse being blown.

Posted on Mar 19, 2011

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

My signals and flashers. changed every thing and nothing. running lights work. its a 78 camaro.

Check the plug at the fire wall. Corrosion . Most likely hard wire it. Eliminate the plug. Lucky for you, it has no computers on it. You will have to start with power and grounds to the turn signal an fuse panel. Work your way threw it. A wiring schematic wold help, but good luck on finding one for a 78.

May 19, 2016 | Chevrolet Camaro Cars & Trucks

1 Answer

Lost turn signals, brake light, dash light, and speed ometer quit. i have head light and tail light, fuse blew then replaced fuse then it blew again.

Pull primary cover, primary chain and clutch, then rotor from crankshaft... check Stator for shorts to ground... same thing happened to mine... now is fixed!

Aug 05, 2013 | 2002 Harley Davidson FXDWG Dyna Wide Glide

1 Answer

Check engine light----speed control

Sound like a problem with the vehicle speed sensor; if your check engine light is on, then I suggest scanned the computer to know exactly what fault code is stored there.

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Jun 21, 2012 | 1999 Ford Taurus

1 Answer

1980 xj650 runs but no lights at all and fuses are good. what next?

check the rrelay for the instruments and especially the lights

Jun 12, 2012 | Yamaha XJ 650 Motorcycles

1 Answer

When we recieved the bike all the wires were unhooked the harness is there but nothing is conected so need the diagram so we can wire this bike to run. It has head lights,tail lights,turn signals, and a...

sir , no need of diagram to hook the harness because all the males are matches to their own female just note the colours,pins,cupler sizes and fix it one by one to matching plugs...thanks

Apr 26, 2011 | Yamaha YZF-R1 Motorcycles

1 Answer

Fuses panel described in English

Hope this helps your out. I know the diagram and locator is a bit blurry but hopefully it gets what you need.
Drivers kick panel:
Front wiper 20A - Front wiper system Cigar 15A- Cigarette lighter Audio 10A- Audio, remote control mirror Air Bag 10A -Air bag diagnostics Stop lights- 15A -Rear brake light, high mounted stop light ECU B+ 10A - Shift lock actuator, transaxle controle module, radio, engine control module Room 10A - Interior light, clock, ignition key reminder, rear cargo area light switch ABS 10A- Anti lock brake system control unit ECU IG1 10A - Transaxle control module, shift lock actuator, ABS control unit, DRL unit Meter 10A - Instrument panel, back-up switch, electronics time control module, inhibit switch Turn signal 10A- Hazard switch ,front and rear turn lights, turn indicator IGN1 20A - Ignition switch ABS 30A- ABS pump motor TNS 30A- Tail light, license plate light COOL/FAN 30A- Cooling fan Cond/Fan 20A- A/C condenser fan Starter 15A- Start signal , Fuel pump Blower 25A- Blower Motor SR/ACC 10A - Ignition switch Hazard 15A - Hazard and turn signal light D/Lock 25A- Door locks ABS 30A - Anti lock brake system control P/W RH 20A- Power window motor right hand P/W LH 20A- Power window motor left hand IGN2 25A- Ignition Switch
Engine compartment :
Head 25A- headlights IG 2 30A- Ignition switch IG coil 15A -Ignition coil, condenser,generator IC regulator, diagnostic connector. O2 down 10A- Rear O2 sensor O2 up 10A- Front O2 sensor Fuel pump 10A -Fuel pump unit Injector 10A -Fuel injector ,camshaft positioning sensor, purge solenoid valve, EVAP, IAC actuator, Mass Airflow sensor, EGR stepper motor. fuel pump relay coil, vehicle speed sensor. A/Con 10A - A/C compressor controls, cooling fan BTN 30A- Brake light , high mounted stop light. Tail light LH 10A- License plate light, tail light , rear combo light, instrument panel illumination Tail light RH 10A-License plate light, tail light , rear combo light, instrument panel illumination Head low 15A- Headlight Head Hi 15A-Headlight Horn 15A- Horn jlmacman.png jlmacman_0.png

Inside kick panel jlmacman_1.png

Mar 07, 2011 | 1995 Kia Sephia

1 Answer

Yamaha at night my speedometer and tac lights rent

You should be able to access the speedo and tac lights via the rear of the console. Check the bulbs and replace if required. If this does not help, please reply or further information

Apr 06, 2010 | 1995 Yamaha FZR 600

1 Answer

My 95 chevy tahoe has new tranny shifts fine when its cold but once it heats up the speed ometer and tac dont work it shifts like ****

Sounds like you have an electrical problem. Your truck should have a 4l60E in it, which is controlled by the PCM. If the speed signal is missing it will shift poorly and at the wrong times. Check the connection and wires at the vehicle speed sensor on the drivers side of the tailshaft housing. If this is something that started occurring after the the transmission was replaced look for pinched wires or other damage to the wires that may have been done during the installation. I've seen some sloppy transmission shops damage things or leave stuff loose so just go over everything.

Feb 11, 2010 | 1995 Chevrolet Tahoe

3 Answers

What causes left turn signal to blink rapidly? And how to fix it?

If only the left signal is blinking rapidly, it indicates a blown bulb. Open the trunk and you can access the rear of the tail light assembly. Then twist and remove the bulb retainer from the assembly and change the bulb. Align the bulb retainer and twist back into position. Hope this helped and best wishes.

Aug 06, 2009 | 2001 Chevrolet Cavalier

Not finding what you are looking for?
2008 Suzuki Boulevard Logo

160 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts


Level 3 Expert

75822 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Ed Nelson
Ed Nelson

Level 2 Expert

149 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides