Question about kawasaki KX 450 F Motorcycles

1 Answer

Cant get flywheel off jet ski 2 stroke Kawasaki 2005 sxr. I used puller tool but ended up stripping threads in flywheel not bolt. flywheel has moved about 1/4" max but wont go any more. Have hit it, heated it, oiled it, and now trying a pry bar and still wont pop off.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 148 Answers

Get as much crc as you can in there,try to hit it back on,reheat and try to remove again,,if this fails you will have to cut it off.

Posted on Mar 19, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i remove a primary clutch on a 1973 344t massey fergusson ski wiz


Remove the main clutch bolt,thread in the appropriate clutch puller,tighten with an air gun,smack the end of the puller with a bfg! Make sure you obtain the right puller. you dont want to strip the threads out of the inside of the clutch or it will never come off.

Nov 18, 2014 | Winter Sports

1 Answer

Mcculloch


How many bolt holes are in the flywheel? Mostly 3 holes plus the one in the centre.I used a steering wheel puller and I removed the centre nut to the end of the threads then attached the puller the flywheel.Then proceeded to tighten the puller slowly till the flywheel was loose.Then I removed the puller also removed the centre nut and proceeded to remove the flywheel.Hope this helps.I'm not much at explaining on computer but in person I show you faster. (1) BUT always remember to make the puller is square or level with the flywheel.So that way all 3 bolts are pulling the same time.(2) PLEASE BE CAUTIOUS!!!!...

Aug 27, 2014 | Garden

2 Answers

Bad stator on ski doo. how do i change it?


wot model is it , 2 or 4 stroke engine ? let me know as i am a marine engineer for 29 yrs and have worked on jet skis , outboards , inboards of all makes !!! P...

Oct 24, 2013 | Motorcycles

1 Answer

What direction does the flywheel nut come off on a 1971 kawasaki 90cc?


Hi, kawasaki use a normal thread on the flywheel retaining nut , anti clockwise will undo the nut, once the nut is removed, you will need a flywheel puller, the thread within the flywheel for the puller, is a lefthand thread, if you dont have a puller, its the same one as suzuki 50, yamaha 50 and honda50 which can be bought realitivly cheap, always remove washer from flywheel when usin a puller to ensure it screws all the way home

Aug 26, 2011 | kawasaki KR-1 Motorcycles

1 Answer

How do i get the fly wheel off of my 5hp techumseh engine without breaking it


Hi and welcome to FixYa. I am Kelly

There are 3 ways to get it off.
1. Use the flywheel remover tool from tecumseh that threads onto the crankshaft threads. Tiy then strike that tool with a hammer to loosen the flywheel on the tapered shaft while applying a prying force under the flywheel.
2. Back the nut off on the crankshaft until the nut face is just flush with the bitter end of the crankshaft. The use a VERY large screwdriver or mini-crowbar under the flywheel to apply prying force. I find it is best if you use both a very large screw driver and a mini-crowbar while a 2nd person strikes the NUT flat / straight down on the end of the crank shaft. It will pop free and probably scare you when it comes loose. After it comes loose remove the nut and the flywheel.
NOTE: Many of these engines have an OFFSET flywheel key if the engine has electronic ignition. If your not sure about the integrity of the flywheel key replace it. They are cheap.
3. If the flywheel has 2 threaded holes in it... you can make a flat puller plate with 2 holes that will cover the end of the crankshaft and the 2 holes you drill in the plate match up with the holes in the flywheel. You then use long bolts to screw into the 2 holes of the flywheel and the flat plate acts as a puller. You tension the bolts and strike the plate to get it to come free.

I have done all 3 of the above repeatedly. Just be careful when prying on the block so that you do NOT punch a hole in the case. Pry on the ribbed area of the block if possible. If not put a metal plate or thin block of wood against the case so as not to damage it.

Thanks for choosing FixYa,
Kelly

Jul 08, 2011 | Garden

1 Answer

I have a yz80 and i cant figure out how to pull the flywheel


Hi,,,where the nut bolts on to the flywheel,,the flywheel has inner threads,,,you need to purchase a yamaha flywheel puller tool,,,this screws into the flywheel thread and has a bolt in the middle,which you do up and the flywheel pops off,,,these flywheel pullers are cheaply available on e-bay.

good luck

Mar 25, 2011 | Yamaha YZ 125 Motorcycles

1 Answer

I have a 1995 kawasaki zxi the bolts on top of


The numbers on the head are the torque pattern/order. Two stroke motors generally use a torque value of 18 to 22 foot pounds on the head bolts/nuts.

Feb 01, 2010 | Encore Software Kawasaki Jet Ski...

1 Answer

Hey guys, for some reason I cant get my rotor off on a kdx 200 1989. i broke the puller, stripped the 3 bolts holding the puller in place, tried a bearing puller, broke that aswell! Tried some pennetrating...


Hi, sometimes you have to put tension on the puller, then give the end a few taps with a soft hammer, be careful not to damage the crank thread, otherwise you may have to heat the centre of the rotor, also, when you take the rotor bolt out, is there a larger thread on the inside of the hole in the rotor, this is where the puller goes on a lot of bikes, but has to be a specific bike puller, hope this helps :)

Jan 11, 2010 | 1998 kawasaki KDX 200

1 Answer

How do you remove a stator on a 1992 honda cr250 2 stroke


Stator unbolts, do you mean flywheel? You need a puller for it, it threads into the flywheel, after you remove the center bolt, left handed threads.

Nov 16, 2009 | 2002 Honda CR 250 R

1 Answer

Rolled our 2007 800 SXR - ended up upside down. Rolled it clockwise back to upright. Re-started it without looking into engine compartment. It ran 5-6 seconds then stopped. Now the starter can't turn the...


i would remove all of the water and then manually turn the engine over alot without starting it SOON to get the water out of the pistons- if it was hydro locked this might prove quite challenging.

Aug 06, 2009 | 2000 kawasaki VN 2000 Classic LT

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

251 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4533 Answers

yadayada
yadayada

Level 3 Expert

76630 Answers

bazzz7071
bazzz7071

Level 2 Expert

342 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...