Question about 2006 Yamaha YZF-R1

1 Answer

2006 yamaha R1. stalled @ a stop sign. wont restart. it tries 2 turn over but will only crank once then clicks once and then dash resets. changed battery but no difference

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

  • Yamaha Expert
  • 191 Answers

Get a multimeter and test the battery voltage right at the posts...if its fully charged you should see 12.6 V....now test while trying to crank....if battery voltage remains high11.5 V...but you get the clicks...you have a bad connection....thoroughly clean the battery cables and make sure they are secure.

Posted on Mar 18, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi someone tried to Hotwire my bike ran power to somewhere they shouldn't now my imobiliser light has stopped flashing and bike won't start it's cranking but nothing can u help it's a 06 r6


Hi, Michael look at it this way your security system worked but it appears the thief may have fried your security module for this situation I would call my local dealer or reputable shop's service/parts department and inquire about any possible quick fix, answers, or parts inquiry. For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
http://www.r6-forum.com/forums/57-garage-mechanical-help/153806-2006-r6-wont-start.html
http://www.r1-forum.com/forums/2-general-motorcycle-discussions/179669-bike-wont-start-after-power-wash-please-help.html
Yamaha YZF R6 2006 Service Manual
OEM parts for Yamaha
Yamaha 2006 YZF R6V Owner Manual

Feb 21, 2017 | 2006 Yamaha YZF-R6

1 Answer

Changed the battery in my 2006 yamaha r6 now it wont rev up


Hi, Anonymous and the usual suspects are:
1. Ignition Switch not in the "ON" position.
2. Engine Run Switch in the "OFF" position.
3. Discharged battery, needs to be 12.5 volts or better and be able to pass a load test if necessary.
4. Check the battery terminals for damage or corrosion check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
5. Tip over sensor needs a reset.
6. Faulty ignition switch.
7. Faulty starter button.
8. Faulty kickstand or clutch pull in switch/sensor.
9. Starter control circuit, relay, or solenoid faulty.
10. Main fuse or circuit breaker may be blown or faulty.
11. Check for engine trouble codes.
For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have nice a day.
http://www.r1-forum.com/forums/104-04-06-r1-mechanical-help/323828-battery-charged-bike-still-wont-start.html
http://www.r6-forum.com/forums/57-garage-mechanical-help/153806-2006-r6-wont-start.html
http://www.r6messagenet.com/forums/pdf/2006R6Service.pdf
OEM parts for Yamaha
http://mybikemanuals.com/yamaha/yamaha-yz-owners-manuals

May 06, 2014 | 2006 Yamaha YZF-R6

1 Answer

Battery voltage drop


Sounds like the starter motor itself. Does the engine turn at all when you try to crank it?

Feb 14, 2014 | Yamaha YZF-R1 Motorcycles

1 Answer

Bike stalls at stops


Hi, Anonymous and the usual suspects are:
1. Idle circuit and transfer ports clogged.
2. Air fuel mixture adjustment too lean.
3. Pilot jet clogged.
4. Faulty accelerator pump.
5. Float level too low.
6. Float bowl contaminated old fuel, water, dirt, rust, etc.
7. Float bowl vent or overflow tube clogged.
8. Fuel flow to carburetor restricted.
9. Intake manifold leak.
10. The gas cap is not venting properly or fuel tank venting system blocked.
11. Vacuum line from intake manifold to petcock broken, cracked, or not attached, carburetor vent line plugged.
12. Needle and seat stuck closed in the float bowl.
For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have nice a day.
http://www.r6-forum.com/forums/57-garage-mechanical-help/91441-bike-stalling-when-i-stop-wont-stay-idle.html
2007 2008 Yamaha R1 Stalling Problem Fix How to
1999 2002 Yamaha YZF R6 Service Manual R6 Moto Data Project
OEM parts for Yamaha
http://mybikemanuals.com/yamaha/yamaha-yz-owners-manuals

Jan 08, 2014 | 2000 Yamaha YZF-R6

1 Answer

My r1 wont start


I think you broke the timing chain. You have to take it to a specialist. Don't try to crank it you will only damage the engine. The timing chain is something like the picture... 11_22_2013_11_35_23_pm.png

Nov 15, 2013 | Motorcycles

1 Answer

Bike wont idle when cold, have to open throttle to keep running.


Hi, Anonymous the carburetor throttle shaft wheel has two cables the cable closest to the right side of the bike is the throttle cable and the one closest to the left side is the idle cable. Right about the middle between the two is the idle adjustment bolt it faces out towards the air filter end of the carb . The engine should be at operating temperature with the enrichener off to set the idle between 950-1050 rpm. Turn the idle adjustment bolt clockwise to increases idle speed and counterclockwise to decrease idle speed. If you have access to your air fuel mixture bolt you may adjust it as well if not there is a video below on how to gain access, make sure you start with clean or new spark plugs. Gently turn the air fuel mixture bolt clockwise until it starts to bottom out "STOP" do not over tighten as it will damage the taper on the end, now back it out 2 full turns to establish a starting point start the engine and check the idle rpm's and adjust the idle adjustment bolt accordingly for 950-1050 rpm if necessary, adjust the air fuel mixture bolt 1/4 turn at a time and let the engine settle for about 10 seconds, clockwise for a leaner mixture and counterclockwise for a richer mixture you are seeking the highest rpm your air fuel mixture bolt can acquire without going past 3 full turns from bottom then readjusting the idle adjustment bolt back down to 950-1050 rpm If you can not detect any rpm change and can not stall the engine by turning the air-fuel mixture bolt all the way in then your pilot/low-speed jet is too big. Final adjustment should be made with a clean air filter mounted to the carburetor. For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have nice a day.
http://www.r1-forum.com/forums/102-00-01-r1-mechanical-help/178565-wont-idle.html
07 r6 rough idle then stalls on cold start
http://www.lethaladrenalinrydaz.com/index.php/service-manuals/finish/3-service-manuals/6-2007-2008-yamaha-r1-service-manual/0
OEM parts for Yamaha
http://mybikemanuals.com/yamaha/yamaha-yz-owners-manuals

Jan 04, 2013 | 2008 Yamaha YZF-R1

1 Answer

Yamaha R1 won't start after I adjusted the valves.


Hi, Jason for this scenario you will need your service/owners manual if you can't find the first and best tool you ever bought for your Yamaha, despair not, for a mere $10 you can download another one. For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have a nice day.
http://www.r6messagenet.com/forums/r6-maintenance-technical/982-remounted-motor-adjusted-valves-bike-wont-start.html
Yamaha R1 Valve Adjustment Compression Test
Yamaha YZF R1 Service Repair Workshop Manual 04 06 Download Manuals...
OEM parts for Yamaha
http://mybikemanuals.com/yamaha/yamaha-yz-owners-manuals

Apr 21, 2012 | 2000 Yamaha YZF-R1

1 Answer

2006 r1 wont start stoped and road end


Hi, Anonymous for this scenario you will need your service/owners manual if you can't find the first and best tool you ever bought for your Yamaha, despair not, for a mere $10 you can download another one. For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have a nice day.
R1 01 won start after storage
http://www.r6-forum.com/forums/46-general-discussions/81502-wont-start-after-long-winter.html
Yamaha YZF R1 Service Repair Workshop Manual 04 06 Download Manuals...
OEM parts for Yamaha
http://mybikemanuals.com/yamaha/yamaha-yz-owners-manuals

Apr 07, 2012 | 2006 Yamaha YZF-R1

1 Answer

How to reset key r1


Hi, Tom for this situation I would call my local dealer or reputable shop's service/parts department and inquire about any possible quick fix, answers, or parts inquiry. For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have a nice day.
http://www.r1-forum.com/forums/2-general-motorcycle-discussions/163167-reprogram-r1-key-anyone-do.html
http://www.r1-forum.com/forums/104-04-06-r1-mechanical-help/550026-ecu-reset-key-issues-help.html
Yamaha YZF R1 Service Repair Workshop Manual 04 06 Download Manuals...
OEM parts for Yamaha
http://mybikemanuals.com/yamaha/yamaha-yz-owners-manuals

Oct 29, 2010 | 2006 Yamaha YZF-R1

1 Answer

When starting from cold ticks over ok .once warm if i then stop and restart it stalls at tickover


Hi, Tom and the usual suspects are:
1. Idle circuit and transfer ports clogged.
2. Air fuel mixture adjustment too lean.
3. Pilot jet clogged.
4. Faulty accelerator pump.
5. Float level too low.
6. Float bowl contaminated old fuel, water, dirt, rust, etc.
7. Float bowl vent or overflow tube clogged.
8. Fuel flow to carburetor restricted.
9. Intake manifold leak.
10. The gas cap is not venting properly or fuel tank venting system blocked.
11. Vacuum line from intake manifold to petcock broken, cracked, or not attached, carburetor vent line plugged.
12. Needle and seat stuck closed in the float bowl.
For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have nice a day.
http://www.r1-forum.com/forums/102-00-01-r1-mechanical-help/178565-wont-idle.html
Engine starting and idle speed
Yamaha R1 YZFR1 2007 2008 Service Repair Manual Download Download Manuals...
OEM parts for Yamaha
http://mybikemanuals.com/yamaha/yamaha-yz-owners-manuals

Dec 23, 2009 | 2008 Yamaha YZF-R1

Not finding what you are looking for?
2006 Yamaha YZF-R1 Logo

Related Topics:

322 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Experts

dhnguyen

Level 2 Expert

281 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1144 Answers

Tony

Level 3 Expert

2600 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...