Question about 2001 Suzuki GSX 1300 R Hayabusa

1 Answer

What do the numbers on the gauge mean 001 and 021

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 84 Answers

Hi there is this to do with the dreaded fi code c001 c021 mine are from a gsxr 600 but will post a link to get you the codes for a 600 and you can go from there http://www.gsxr.com/showthread.php?t=1234&highlight=codes hope this can be of use best of luck bud

Posted on Mar 17, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What does the red thermometer light mean on my Neff oven?


Please provide me with model number from the serial plate.

Feb 17, 2016 | Neff Ovens

1 Answer

Free answer "93 Lexus head bolt torque


it means that after the initial torque setting of 25 ft/lbs you put the torque wrench away and use a socket and bar to move the head of the bolt the required number of degrees as per the angle gauge that you will fit over the head of the bolt
so select the first hard stud and torque to 25 ft/lbs
repeat this to all the other head studs in the pattern required to achieve even tightening of the head
put the torque wrench away and fit the angler meter (gauge) on the 1 st stud and tighten to 60 degrees as indicated on the gauge
repeat the process for all the head studs as per the tightening sequence
then start again and tightened again another 60 degrees and so on
modern engines use degrees to achieve the correct stretch of the bolts to get the prescribed crush on the gaskets
this is because engineers found that dry threads , dirty threads and dirty stud holes do not give repeatable tensions on all studs.

May 19, 2015 | Lexus Cars & Trucks

1 Answer

Feeler gauge numbers


If you use a micrometer and measure the guages, you will find they are tapered.

Jan 16, 2014 | MSI L1350D-1672US Netbook

1 Answer

Remington serial number 5951 ilion ny


Serial number means nothing without the model and gauge or caliber.

Dec 16, 2013 | Remington Optics

2 Answers

I have a check Gages light on my 1998 cavalier car, do you know what does that mean?


What it means is that you need to watch your gauges for 15 minutes after you start your engine and make sure that they are showing you engine is operating as it should. check your manual to see if they are showing what they are exposed to. if you do not have a manual reply with all of your gauge start numbers and stop numbers and where the needles are sitting after 15 minutes of running.

Nov 22, 2010 | Chevrolet Cavalier Cars & Trucks

1 Answer

What is proper way to read the meter on the front of the battery charger


The numbers on the gauge is the amount of power the charger is putting out in amps. The lower the gauge reads the more the battery is charged. 0 (zero) means the battery is fully charged.

Nov 19, 2010 | Schumacher & Fast Charge Starter Charger

1 Answer

Can you please give me the tappet settings for a Honda civic 2004 1.6 Vtec please.


Do you mean 1.7L? I do not see a 1.6L in the manual. Instructions from autozone.com are pasted below.

lash:

Intake, 0.007-0.009 in (0.18-0.22mm).

Exhaust, 0.009-0.011 in. (0.23-0.27mm)

Civic
1.7L Engine

NOTE Adjust valves only when the cylinder head temperature is less than 100 degrees F.

  1. Before servicing the vehicle, refer to the precautions in the beginning of this section. Disconnect the negative battery cable.
  2. Note the radio security code and the radio presets.
  3. Remove the ignition coil cover. Remove the ignition coils. Remove the throttle cable clamps and harness holder from the cylinder head cover.
  4. Remove the cylinder head cover retaining bolts. Remove the cylinder head cover from the engine.
  5. Remove the grommet from the upper cover and disconnect the camshaft position (CMO) sensor connector. Remove the upper cover.
  6. Set the number one piston at TDC. The UP mark on the camshaft pulley should be at the top, and the TDC marks on the pulley should line up with the top edge of the cylinder head.
  7. Using the proper gauge feeler gauge, adjust the valves on cylinder number one.
  8. Rotate the crankshaft 180 degrees counterclockwise. The UP mark on the camshaft pulley should be toward the exhaust side of the cylinder head.
  9. Using the proper gauge feeler gauge, adjust the valves on cylinder number three.
  10. Rotate the crankshaft 180 degrees counterclockwise and bring the number four piston to TDC.
  11. Using the proper gauge feeler gauge, adjust the valves on cylinder number four.
  12. Rotate the crankshaft 180 degrees counterclockwise. The UP mark on the camshaft pulley should be toward the intake side of the cylinder head.
  13. Using the proper gauge feeler gauge, adjust the valves on cylinder number two.
  14. Install the cylinder head cover.
  15. As required, reprogram the ECM/PCM engine idle characteristics. Be sure all electrical items are OFF.
  16. Start the engine. Hold the idle speed at 3000 RPM-s in park or neutral until the radiator fan comes on or the temperature reached 194 degrees.
  17. Let the engine idle for about five minutes with the throttle fully closed.
  18. If the radiator fan comes on during the five minutes, do not count this toward the five minute programming time.
  19. Set the clock.

Oct 04, 2010 | Honda Civic Cars & Trucks

1 Answer

Gauge lights up and I cannot tell the meaning of the gauge


Is there any way to describe it?What it resembles or a number or letters or anything?A lightning bolt?Please let me know if you can make out anything at all.Greg

Aug 28, 2010 | 2001 Chevrolet Impala

1 Answer

Wht wire gauge 2 choose?


You can run anywhere from 12 to 16 guage speaker wire. The higher the number the thinner the wire. If you found this solution helpful please rate it.

Thanks - Tech101

Jun 24, 2008 | Audio Players & Recorders

Not finding what you are looking for?
2001 Suzuki GSX 1300 R Hayabusa Logo

Related Topics:

282 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Ed Nelson
Ed Nelson

Level 2 Expert

149 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...