Question about 2000 Gas Gas EC 300

1 Answer

My 96 dr200 idles fine but off idle sounds like its hitting a rev limiter also the kickstand position dont change anything ,popping through the exh. ?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 148 Answers

Ok sounds like a carb blockage,remove and clean carb also could be tight valve clearance check valve clearances

Posted on Mar 20, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have a 1989 Mazda 323, when cold engine idles very high, when very cold it idles so high that rev limiter kicks in, and it revs up, limiter kicks in, revs up limiter kicks in, once it warms up idle drops...


Have it looked at by a dealer,iam not sure here but i think you have a vacumn leak like the feed pipe to the servo split but really you need a mechanic who works on these cars day in day out and they will go straight too the problem for you

Jan 18, 2015 | 1989 Mazda 323

1 Answer

My 96 ford bronco runs rough on acceleration,idles fine. Runs good under light acceleration but if hit the gas hard runs bad and pops. Changed fuel filter no change.what next?


givit a tune--new distributer cap--new plugs and cables--------also have air intake cleaned plus idle control--use a nonchlorinatd solvent sold a napa etc

Jul 22, 2014 | 1996 Ford Bronco

1 Answer

Engine revs


sounds like air getting into carb where it shouldn't, i.e. vacuum pipe from carb to tank or between carb and engine

Mar 18, 2013 | 2007 Honda CRF 150 F

2 Answers

96 Taurus. Won't rev over 4000 revs even in park or neutral


That is the rev limiter kicking in at idle.

Oct 02, 2012 | 1996 Ford Taurus

1 Answer

Hello, i have a stihl ts400 and i just rebuilt the topend(crank,piston,cyl,all bearings and seals.Fires up easy, idles fine,revs fine, but when you hold the throttle down it doesent want to hit rev limiter...


There is not an actual rev limiter. The top end is controlled by the carb. You actually want it to sound a bit rich at full throttle so that it has enough fuel when cutting under a load. What causes me some alarm is the revving up part. If it revs too fast that is a lean condition and can quickly ruin the piston and cylinder much like running straight gas. A torn intake boot can cause this. The high speed spec for the TS400 is 9,600 rpm + OR - 500 RPM. Your saw may not have a needle to adjust the high side as some have only the low speed adjuster. Also when you disassemble and clean the carb always use a new kit with the gaskets and diaphragm. Any Stihl dealer can furnish the kits and they aren't terribly expensive. Often between $10-20.

Jun 26, 2012 | Saws

1 Answer

Runs and starts fine but will not rev over 9,000 rpms, in neutrol or going down the road, runs great, starts great, revs good till 9,000. wont go over lke it cuts out. idles good. what is it, 98 gsxr 750...


First impression was why would anyone rev their motorcycle to 9 grand in neutral? I could see if you were in gear clutch pulled and ready for a "drag" or Race Start but in neutral?

Anyway I can't hear it so if the sound is like it hits 9k and starts popping then two things either an over rev limiter which I doubtr because the engine red lines at 13,500 OR you have a set of spark plugs breaking down under load

May 03, 2011 | Suzuki GSX-R 750 Motorcycles

1 Answer

Vz 800 idles wont rev just stalls


Put your kickstand UP, it has a kill/safety switch on it....Good Luck to you sir, contact me any time...Tim

May 13, 2009 | 1997 Suzuki VZ 800 Marauder

1 Answer

1991 pontiac trans am will start and idle but after 25-2800 rpm'


how about highway driving will it cruse at highway speeds and if you were to step down on it does it bog down ? and does it still have the cats on it ? just a thought..

Apr 28, 2009 | 1991 Pontiac Firebird

2 Answers

Wont rev past 3/8 throttle!! I NEED HELP.


could be. I had a 91 kx 250 that was acting crazy and it turned out to be the stator and cdi box. you can check the stator easly with a omes meter but the cdi box is nearly impossible to check. you pretty much have to buy a new one and try it. also check to see if your power valve is working.

Jan 19, 2009 | 2004 Yamaha YZ 250 F

Not finding what you are looking for?
2000 Gas Gas EC 300 Logo

151 people viewed this question

Ask a Question

Usually answered in minutes!

Top Gas Gas Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Kim Halliwell

Level 1 Expert

32 Answers

Livewyre Studio
Livewyre Studio

Level 1 Expert

24 Answers

Are you a Gas Gas Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...