Question about Harley Davidson FXD Dyna Super Glide Motorcycles

1 Answer

After getting bike ready for season.the rear jug wasnt getting spark.so i replaced coild thinking it went bad.nope?.although after kepping it running for a period of time.it cleared up and ran on both cylinder.drove it home all cool.then this morning started bike at first was good then bike stalled rear jug no spark again.but then after a period of time of keeping it running ran fine afterwards

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,591 Answers

I'd replace the plug first.
If that isn't the issue, I'd go over the entire ignition system from top to bottom.
When yu changed the coil, did you also change the plug wire? sometimes they can crack, and they will arc to ground, so that the plug gets no spark....until the wire warms up and the crack in it closes enough that it doesn't arc anymore.

Posted on Mar 17, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

FI error message on console with the fuel injection light staying on steady.


if not getting hot can only be not firing on the cylinder it connects to, try swapping the plugs about and then see if any other can stays cold or the rear one gets hot. Bikes eh whod have em

Apr 22, 2015 | 2005 Suzuki Boulevard C50T

1 Answer

Bike cuts out at running temperature


You actually may have two problems. First, if you have a spark from a coil, find out why. May be a bad or loose connection. when coils get hot their resistance increases. A leak or bad connection will show up quicker when hot. If the spark comes from the body of the coil, replace it.
Second, your starter may be breaking down when hot. Check the brushes and coils in the starter motor. The same discussion about loose connections also will apply to the starter.
good luck

Apr 08, 2014 | Honda Varadero 125 Motorcycles

1 Answer

2007 harley sreet bob fires but wont stay running


check that a piece of debris from the broken line has not got into the fuel system causing your grief.

Jul 14, 2013 | 2007 Harley Davidson FXDB Dyna Street Bob

1 Answer

Bike seems as if its running on 2 cyclinders


r all the mufflers the same heat--make sure carbs r ok n gas is gitten to um--inspec plug wires n the rest of ign for wear and bad contacts--with an ohmeter n repair manual varius test can be done-sayonnara

Feb 02, 2010 | 1985 Honda CB 700 SC Nighthawk

2 Answers

Starts ok but only running on two cilinders


What have you done if anything to check out this problem?
Several causes could be: 1. Not getting fuel do to clogged jet in the carbs for those cylinders. 2. Fould plugs in those cylinders. 3. Not getting spark to those cylinders/bad coil 4. no compression in cylinders that don't fire.
So run the bike and determine which cylinders are not firing for sure. use a squirtgun and hit the header with some water. running cylinders with smoke the water. non running will not. Then remove and replace the plugs.(look at old ones, all oily=bad) See if they are wet and shiny but not black...Not shiny=no fuel. Tear carbs apart and clean. Check to see if you have spark leave spark plugs unintsalled from motor but installed in spark plug boot. see if they spark when you start it. Do a compression check. wet and dry. could be rings or valves.
If the bike was sitting for a while then probably clogged jets...This is where stabil comes in handy or else drain the bike at the end of the season.

Nov 28, 2009 | 1983 Suzuki Gs 550 L

1 Answer

Snow blower spark plug replacement


I would check it at the start of every season and clean it. If you note that it seems to be running rich and might have fouled the plug, you can always pull it and check it again. Probably not a bad idea to check it before you put it away for the season. As for replacement, it depends on condition. I would think that you should get two or three season's use out of it before needing to replace it, at least.

Jan 25, 2009 | Toro Lawn Mower With Toro Power Tools

1 Answer

Lam replaced


you dont reset it the ballast for the bulb took a ****.. i paid 300 for a new bulb and wasnt the problem then paid 150 for new ballast now i think the light engine went bad geeze

Sep 23, 2008 | Hitachi 50V500 50 in. HD-Ready LCD...

1 Answer

Wont start


if the coild pack is getting power but you are not get power out the plug side the coil pack is most likely is bad.

May 27, 2008 | 1998 Plymouth Breeze

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

169 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4521 Answers

Mike

Level 3 Expert

4339 Answers

yadayada
yadayada

Level 3 Expert

76051 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...