Question about Yamaha MT-03 Motorcycles

1 Answer

My new motorbike won't start, when I turn the key to on there is no power/ ligths on the digital board

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 16 Answers

IF IT IS NEW YOU NEED TO TAKE IT BACK TO WHERE YOU GOT IT BECAUSE IT IS UNDER WARRENTY,SHOULD BE AND IT WONT COST YOU ANYTHING,OR MAKE SURE YOUR BATTERY IS 12 VOLTS CHARGED BEFORE TESTING ANYTHING ELECTRICAL SO YOU ARE GETTING A TRUE READING.OBVIOUSLY CHECK FUSES.IT IS QUITE POSSIBLE YOU MAY OF GOTTEN A BATTERY WITH A BAD CELL,IT HAPPENS BIKES ARE SHIPPED IN THE FALL AND IF YOU BOUGHT YOURS IN THE SPRING ,MY GUESS IT WAS LEFT CRATED OUTSIDE FOR THE WINTER

Posted on Mar 17, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

96 Jaguar XJ6 No start


need to run a scan on it

Feb 21, 2014 | 1997 Jaguar XJ6

1 Answer

I got samsung tv ln32a330j1d it won"t turn on even


You have a bad power supply.
You can get get parts for this tv at www.interliquidparts.com

Aug 28, 2011 | Samsung LN32A330 32 in. LCD TV

1 Answer

Car won't start when key is turned on but can be push started. Battery is new,


See the small wire on the solonoid top of the starter body.. it might be disconnected.. if it is connected see the fuse. other option, If you have a ligth bulb connect one wire to small wire on solonoid and body ground second wire of your ligth bulb. spin the ignition key to start position if the light bulb does not light there is a cut wire from the ignition key to solonoid.

Aug 18, 2011 | 1991 Honda Accord

1 Answer

My sony bravia 46" doesnt


hi,
you have to replace the inverter board. If the invereter board overloaded the powers supply, then the tv will go to standby after some time.
ok

Jun 21, 2011 | Sony Bravia KDL-46V4100 46 in. LCD HDTV

1 Answer

I have a 1986 silver spirit which looses power .it will tick over and run for about one minute .when you accelerate it looses all power .is this a fuel starvation problem.if i turn the car off then start...


check fuel pressure, ignition source , timing,plugs ,dist& rotor ,coil ,sensors , does check engine ligth on or comes on . just turn key on no start see if check engine ligth comes on

Nov 05, 2010 | Rolls Royce Silver Spirit Cars & Trucks

1 Answer

I change the turn signal lever I took apart unplunged everything carefully put everyhing back together carefully but as I was workig on it I heard my horn honk twice I look no bear wires anywhere finish...


your security system is activated. try turning the key on let set for 10 minutes turn it off then start. on some models it has to be done 3 times on off on off on off start. 10 minutes each time

Jun 22, 2010 | 2000 Chevrolet Tahoe

1 Answer

2002 ford explorer key turns all the lights come on but will not turn over


try starting it up in neutral or check the anti thef ligth it should com on and then com of when you turn the key on but if it remainds on or flashing yuo must get a new key

Sep 19, 2009 | 2002 Ford Explorer

1 Answer

I have di1610 wont at all error ligth are flashing


Description
Machine may cycle ON/OFF repeatedly (keeps rebooting), will not power ON (no boot-up), no message on the operation panel, LCD displays extraneous
characters and/or error code C14A3 (C-14A3).
Solution
CAUSE: The PCL board draws too much current, causing PWB-P to fail. There is no problem with GDI versions of the machine; only machines with PCL
boards are affected.
SOLUTION: The PCL board has been modified to limit current draw. If the symptoms described above occur, replace both the PCL and PWB-P boards.

Note : The new-style PCL board can be identified by a yellow sticker. Machines that had the new-style board installed during production have a yellow
sticker near the serial number plate.

may want a service technician to check the PCL boards as above

Aug 04, 2009 | Minolta Office Equipment & Supplies

1 Answer

Ligth on in the dust board maint rejd


factory settings to alert you of routine maintenance intervals, not the same as "check engine" which instead indicates a problem. The reset for this is w/ the key off, hold in your trip button on the odometer, while holding it in turn the key so that everything powers on, don't start it, just turn the key forward, while still holding the trip button in, watch the "maint req'd" light, after about 10 secs it will go out, then release the trip button, thats it.

Apr 04, 2009 | 2003 Honda Civic

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

120 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Experts

dhnguyen

Level 2 Expert

281 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1144 Answers

Tony

Level 3 Expert

2600 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...