Question about 2005 Hyosung GT 250

1 Answer

Fuel coming out of air tank hose when running

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Champion:

    An expert who has answered 200 questions.

  • Hyosung Expert
  • 473 Answers

That is a pressure bleed off, sometimes liquid fuel gets caught in the way. especially if you fill the bike up as full as you can get it.

Posted on Oct 21, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

Slow fill gas tank


either fluid is in the vent hose or the fill hose is pinched off somewhere under the car.. mechanic/tech can use an air hose to check for blockage

Apr 11, 2014 | 2000 Hyundai Elantra

4 Answers

The hose is on the side of the gas cap and it runs down to the bottom of the quarter panel. When I filled the gas tank up, gas comes out of this hose. We just had the fuel pump replaced. Its not leaking...


There are normally two hose lines from the fuel filler that run to the tank. The larger one carries the fuel from the nozzle to the tank. The smaller one is a vent hose that allows vapors to leave the top of the tank while filling. These vapors come back to the nozzle area and can be vented and/or collected by the nozzle depending upon air pollution standards in your area. If your second hose is running to the bottom of the quarter panel, it is probably the vent hose that may not have been reconnected at the top of the tank when the fuel pump was replaced. The fuel running down there is from kickback fuel at the time the pump shuts off. The real problem is that the vent line is open on top of the tank and when the tank is full, that can allow vapors and fuel to escape out of there and it could contact hot exhaust areas - a major fire or explosion hazard. Have this inspected and repaired IMMEDIATELY.

Nov 05, 2013 | Ford Mustang Cars & Trucks

6 Answers

Pressure build up in gas tank Sporster


Harley Davidson has handled gas tank venting in a couple ways over the years. One is to allow the venting to be done by the gas cap the second is to have a non-venting cap and connect a vent hose to the tank which vents air from the top of the tank. You said your hose was dry rotted so it should be replaced. However, I don't feel that, by itself, would allow pressure to build up. Replace the hose and, while it's off, ensure the connection to the top of the tank is not plugged. When you put the tank back on, ensure the hose doesn't get crushed. It sounds like proper venting is all that is required.

Something else to consider is that a plugged vent would, most likely, cause a vacuum in the tank instead of pressure. (As the tank empties while riding, air can't come in to fill the space vacated by the gas.) The only reason I could expect that you build up pressure is if the vent is plugged and the tank gets heated from an outside source such as the sun.

I hope this is helpful.

Mar 26, 2017 | 2005 kawasaki EN 500 Vulcan

1 Answer

I have a 2005 T&C 3.3 and I just bought Seafoam and it says to put it in your air intake hose. Where is that located at? I have look at pictures and no avail.


You can run it through your air cleaner hose slowly while the vehicle is running it will be the hose that comes from your air filter box to the air horn on the upper intake. Or you can pour it in your fuel tank so it will clean your fuel injectors and all.

Jun 23, 2011 | 2005 Chrysler Town & Country

1 Answer

Replaced primer bulb and all fuel lines still getting air in lines. ran pretty good for about 10 minutes now will start with choke but dies in a few seconds. Cannot rev. up. cleaned under both plates but...


The primer bulb pulls fuel from bottom of fuel tank,when bulb is full it will return fuel back into tank,the hose entering bulb runs in the tank to bottom with filter on the end,the return hose stops just as it enters the tank maybe 3/4",make sure the hoses entering tank are tight fit or they will pull air in and leak.the carb may also need rebuild/clean,there is a screen inside of carb that may be stopped up which will need to be replaced.(carb kit).

Feb 18, 2011 | Troy Bilt Tb70ss Gas Trimmer

2 Answers

Generqator stalls


Make sure the on/off to the gas tank is on and no craks in the gas line. aslo check and see if you have any slack on the governer's spring

Sep 09, 2009 | Electrical Supplies

2 Answers

Kawasaki z750 abs. Vacuum (pression) in fuel tank


If you're building up vacuum or pressure in the fuel tank, your vent line is pinched or plugged. It is a rubber hose that comes off the fuel tank, usually runs down the right side and discharges vented air out the bottom somewhere.

Jun 25, 2009 | 2008 kawasaki Z750 Abs

1 Answer

KAWASAKI Z750 ABS vacuum (pressure) in the gas tank


If you're building up vacuum or pressure in the fuel tank, your vent line is pinched or plugged. It is a rubber hose that comes off the fuel tank, usually runs down the right side and discharges vented air out the bottom somewhere.

Jun 25, 2009 | 1985 Honda XR 250 R

2 Answers

How do you replace the fuel pump in 1992 2wd Subaru Legacy Wagon


  1. Relieve the fuel system pressure.
  2. Disconnect the negative battery cable.
  3. Remove the rear exhaust pipe and muffler assembly.
  4. On All Wheel Drive (AWD) vehicles, remove the rear differential assembly and the rear crossmember. You do not have AWD so this step is not for you
  5. Remove the fuel filler cap and drain the fuel into a suitable container.
  6. Remove the fuel filler pipe protector.
  7. Raise and support the vehicle safely on jackstands.
  8. Remove the fuel filler, air vent and delivery hoses.
  9. On AWD vehicles, disconnect the air breather hoses and evaporation hose from the pipes.
  10. Support the fuel tank with a floor jack or equivalent lifting device.
  11. Loosen the attaching bolts and lower the fuel tank slightly.
  12. Disconnect the fuel pump harness

Feb 18, 2009 | 1992 Subaru Legacy

Not finding what you are looking for?
2005 Hyosung GT 250 Logo

Related Topics:

55 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyosung Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Hyosung Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...