Question about 2001 Suzuki GZ 250 Marauder

1 Answer

Oil filter cover bolts dont tighten what should i do? Cover is loose and cant change oil filter.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

What i would do is either get some biger screws and re thread it or get some thread fixers they sale at auto zone if its not to bad though high heat sealent works good to put in the holes and around the edges.

Posted on Mar 16, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace oil; cooler on this year


  • Service and Repair
Oil Cooler Replacement

Removal Procedure

  1. Raise and support the vehicle. Refer to Vehicle Lifting.
  2. Drain the engine oil and remove the oil filter housing.
89116492

  1. Loosen the oil cooler outlet (1) and the inlet (2) lines from the engine block.
  2. Lower the vehicle.
  3. Remove the intake plenum.
  4. Remove the intake manifold.
89116493

  1. Disconnect the following electrical connectors from the water crossover:
    • The engine coolant temperature sender (2)
    • The engine coolant temperature sensor (4)
84936658

  1. Remove the water crossover bolts (1).
  2. Remove the water crossover upper and lower seals (2).
84942881

  1. Loosen the upper heat shield bolts on the left side of the exhaust manifold.
89116496

  1. Remove the oil cooler outlet line from the engine oil cooler.
  2. Remove the oil cooler inlet line from the engine oil cooler.
84942883

  1. Note the positioning of the 4 seals.
84972057

  1. Position the oil feed and return,lines out of the way and secure with mechanic wire.
  2. Remove the engine oil cooler, inlet and outlet nuts (1).
  3. Remove the engine oil cooler cover bolts (2).
84942883

  1. Remove the engine oil cooler cover.
  2. Remove the engine oil cooler.
  3. Clean all sealing surfaces.
Installation Procedure
84972056

  1. Install the engine oil cooler.
  2. Apply a 2 mm (0.08 inch) bead of RTV silicone sealant, GM P/N 12346240, in the groove around the engine oil cooler cover.
  3. Install the engine oil cooler cover.
Notice: Refer to Fastener Notice in Service Precautions.
84972057

  1. Install the engine oil cooler cover bolts (2). Tighten the engine oil cooler cover bolts to 30 Nm (22 ft. lbs.).
  2. Install the engine oil cooler inlet and outlet nuts (1). Tighten the engine oil cooler inlet and outlet nuts to 20 Nm (15 ft. lbs.).
  3. Reposition the oil feed and return lines.
84942883

  1. Install the oil cooler outlet and install the oil cooler inlet lines to the engine oil cooler. Use 4 new seals.
Tighten the oil feed and return lines to 30 Nm (22 ft. lbs.).
84936658

  1. Install the water crossover:
    • Position the crossover.
    • Install the upper and lower seals (2).
    • Install the water crossover bolts (1). Tighten
Tighten the water crossover bolts to 30 Nm (22 ft. lbs.).
  1. Connect the electrical connectors at the following locations:
    • The engine coolant temperature sensor (4)
    • The engine coolant temperature sender (2)
  1. Install the intake manifold.
  2. Install the intake plenum.
  3. Raise the vehicle.
89116492

  1. Install the oil cooler outlet (1) line to the engine block. Tighten the oil cooler outlet (1) line to 30 Nm (22 ft. lbs.).
  2. Install the oil cooler inlet (2) line to the engine block. Tighten the oil cooler inlet (2) line to 30 Nm (22 ft. lbs.).
  3. Install the oil filter housing to the engine block. Tighten the oil filter housing to 45 Nm (33 ft. lbs.).
  4. Lower the vehicle.

Dec 22, 2014 | 2001 Cadillac Catera

1 Answer

I need head bolt torque specs for a 2000 cadillac deville dts..


DeVille, Eldorado, Seville 1999-2005

Cylinder Head

Print


Removal & Installation

Left Side

  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the cooling system.
  3. Properly relieve the fuel system pressure.
  4. Remove or disconnect the following:

    Negative battery cable Exhaust manifold Alternator Water crossover Intake manifold Valve cover Timing cover Secondary camshaft drive chain Power steering return hose retaining bolt from the cylinder head 3 M6 external drive bolts from the front portion of the cylinder head 10 M11 internal drive cylinder head bolts Cylinder head and gasket.
  5. Clean the head mating surfaces.

To install:

0996b43f80231662.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Left cylinder head bolt torque sequence-4.6L engine

  1. Install the cylinder head with a new gasket. Lubricate the bolts with engine oil prior to installation.
  2. Torque the M11 bolts in sequence as follows:
    1. Step 1: 30 ft. lbs. (40 Nm), plus an additional 70 degrees
    2. Step 2: Turn an additional 60 degrees
    3. Step 3: Turn an additional 60 degrees (total 190 degrees)

  3. Torque the M6 bolts to 106 inch lbs. (12 Nm)
  4. Install or connect the following:

    Power steering return hose retaining bolt to the cylinder head and tighten to 37 ft. lbs. (50 Nm) Secondary camshaft drive chain Timing cover Valve cover Intake manifold Water crossover Exhaust manifold Negative battery cable
  5. Change the oil and filter.
  6. Fill the cooling system.

Right Side
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the cooling system.
  3. Properly relieve the fuel system pressure.
  4. Remove or disconnect the following:

    Negative battery cable Exhaust manifold Water crossover Intake manifold Valve cover Timing cover Secondary camshaft drive chain Electrical connector from the Engine Coolant Temperature (ECT) sensor Nut attaching the coil cassette ground wire to the cylinder head Bolt attaching the exhaust crossover pipe to the cylinder head Bolt attaching the right transaxle mount bracket to the cylinder head Bolt attaching the rear transaxle brace to the transaxle Nuts attaching the rear transaxle brace to the cylinder head Rear transaxle brace 3 M6 external drive bolts from the front portion of the cylinder head 10 M11 internal drive cylinder head bolts Cylinder head and gasket
  5. Clean the head mating surfaces.

To install:

0996b43f80231663.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Right cylinder head bolt torque sequence- 4.6L engine

  1. Install the cylinder head with a new gasket. Lubricate the bolts with engine oil prior to installation.
  2. Torque the M11 bolts in sequence as follows:
    1. Step 1: 30 ft. lbs. (40 Nm), plus an additional 70 degrees.
    2. Step 2: Turn an additional 60 degrees.
    3. Step 3: Turn an additional 60 degrees (total 190 degrees).

  3. Torque the M6 bolts to 106 inch lbs. (12 Nm).
  4. Install or connect the following:

    Rear transaxle brace over the studs located at the rear of the right cylinder head Nuts attaching the rear transaxle brace to the cylinder head, loosely Bolts attaching the rear transaxle braces to the transaxle and tighten to 37 ft. lbs. (50 Nm) Nuts attaching the rear transaxle brace to the cylinder head and tighten 37 ft. lbs. (50 Nm) Electrical connector to the ECT sensor Bolt attaching the exhaust crossover pipe to the cylinder head and tighten to 18 ft. lbs. (25 Nm) Nut attaching the coil cassette ground wire to the cylinder head and tighten to 13 ft. lbs. (17 Nm) Secondary camshaft drive chain Timing cover Valve cover Intake manifold Water crossover Exhaust manifold Negative battery cable
  5. Change the oil and filter.
  6. Fill the cooling system.

Apr 16, 2013 | 2000 Cadillac DeVille DTS

1 Answer

Oil change 1994 Cadillac Eldorado


well let me see you have 4.6L engine you need 7.5 quarts of oil with new oil filter.to do the oil change you need large drain pan and oil filter wrench and a metric wrench to remove oil drain plug you need a funnel also.you need first start engine let it run for 5 minutes to warm up thin out the oil so it will flow better.once engine warm up.turn off the engine.open you hood.now safely raise support vechicle on jack stands make sure vechicle parked on solid level ground.place large drain pan under oil pan remove oil drain plug you need a 15m wrench remove drain plug let all old oil drain out until you see slow drip then reinstall oil drain plug dont over tighten drain bolt.then place drain pan under the oil filter then remove oil filter using oil filter wrench or large channel lock pliers.once you remove oil filter wipe oil filter seal surface with clean paper towel.take new oil filter add oil to new filter then install new oil filter hand tight take filter wrench turn oil filter one half more turn dont over tighten will damage oil filter seal.make sure oil pan drain plug is in place. then lower vechicle. remove oil filler cap on the valve cover add new oil to the engine using a funnel to keep from spilling oil all over the valve cover and exhaust manifold.add all 7.5 quarts to oil crank case wait until oil settle down in crank case check oil dip stick oil level should be at the full mark on oil dip stick.dont over fill crank case.once you finished oil level correct crank engine check for oil leaks at oil filter and oil drain plug. if engine running okay you see no oil warning lights you ready wheel and deal.

Nov 20, 2011 | 1994 Cadillac Eldorado

1 Answer

How do i change the oil pump on 97 expedition


Check this procedure for 4.6L and 5.4L Engines...
  1. Remove the timing chain.
  2. Remove the oil pan.
  3. Remove the three oil pump screen and cover bolts, then remove the screen and cover.
  4. Remove the oil pump screen and cover spacer.
  5. Remove the four oil pump mounting bolts, then remove the oil pump from the engine.
To install:
  1. Clean and inspect the mating surfaces.
  2. Install the oil pump and loosely install the four oil pump mounting bolts. Tighten the four oil pump bolts in the sequence shown to 71-106 inch lbs. (8-12 Nm).
zjlimited_2098.jpg

Fig. 2 Tighten the oil pump mounting bolts to 71-106 inch lbs. (8-12 Nm) in the sequence shown - 4.6L and 5.4L engines (click over image for zoom)

  1. Install the oil pump screen and cover spacer to 15-22 ft. lbs. (20-30 Nm).
  2. Install the oil pump screen and cover, then install the three oil pump screen and cover bolts. Tighten the bolts near the oil pick-up screen to 15-22 ft. lbs. (20-30 Nm) and the bolts at the opposite end of the pick-up to 70-106 inch lbs. (8-12 Nm).
  3. Install the timing chains, then install the oil pan.
Hope this helps. Your feedback is important and I'll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using Fixya, and have a nice day

Oct 28, 2011 | 1997 Ford Expedition

1 Answer

Where is the oil filter?


In the front of the motor you will find a round finned cover with a large bolt going through the center of it. Be sure to use a six point socket on the bolt (or you will strip the bolt head). They are usually over tightened. They only need to be snugged up enough to seal the oil in. Do not over tighten when you reinstall the oil filter cover. When placing the new filter in the cup , hold the cup in one hand with the center bolt sticking up , place the spring in the bolt first , then the washer (probably either missing or still stuck to the old filter) and the filter ,so the filter is pushed against the motor.

Oct 02, 2010 | 1981 Yamaha XS 400

1 Answer

How do you change the oil on a 1985honda aspencade goldwing?


Center stand the motorcycle.First place your pan under the oil filter cover under the front right corner of the machine. Using a six point socket loosen the filter cover bolt and remove the cover. Dump out the oil in the cover being careful to save the spring and the washer that is stuck to the filter.Many Goldwings have lost there washer in a previous oil change , if lost replace the washer. If you desire change the o-ring on the bolt and the o-ring on the cover. Put the bolt back into the cover and place the spring first over the bolt, then the washer, then the filter , so the spring is pushing the filter against the engine. Put the new filter onto the motorcycle and snug up the cover bolt just enough so the oil wont leak out. Do Not Over Tighten The Cover Bolt. Now place the pan under the right rear corner of the motor. You will find a horizontal bolt near the bottom right rear corner of the main block of the motor. It will have an aluminum or copper sealing washer. Take off the bolt and let the oil drain out. When the oil is finished draining , put the bolt back in with a new sealing washer , if needed , and snug up the bolt just enough so that it does not leak or come out. Again do not over tighten the bolt. Now pour in the new oil through the dipstick hole. Be sure you use JASO MA certified motorcycle oil. You will need 4 quarts but you may have a partial quart left over. The quantity is something between 3.4 and 4 quarts. Run the bike and double check the oil level with your dipstick so you do not over fill.

Sep 12, 2010 | 1985 Honda GL 1200 Aspencade Gold Wing

3 Answers

Oil leaking from valve cover gasket


Oil sending unit is it hard to replace?

Aug 15, 2010 | 1993 Plymouth Sundance

1 Answer

How to change oil 1978 goldwing gl1000


Get 4 quarts of JASO MA certified motor oil. I recommend synthetic , it will shift better when hot. Amsoil is a good choice. Place an oil pan under the front of the motor. Use a 6 point socket to loosen the bolt on the round finned oil filter cover on the front right corner of the motor and spin it off.Take the oil filter out of the cover and make sure you save the washer that will stick to the rubber seal. Pull bolt out of cover and replace o-ring. put bolt back thru cover, first slide on spring,then washer,and then filter and spin back onto motor pressing filter against engine case. Snug bolt but do not over tighten. Now remove bolt in the middle of the front/bottom of motor(large one in middle , NOT small one under water pump). Check aluminum washer,if bad replace.After oil has drained put bolt back in , do not over tighten.Take off fill plug on right rear corner of motor(by final drive shaft) Using a funnel pour in 4 quarts oil (3.9 is correct amount, 1/10th quart does not seem to bother anything). Put plug back in , start up, and check for leaks.

Jun 02, 2010 | 1978 Honda GL 1000 (K3)

1 Answer

Need to remove external oil pump on a 95 ford tauras 3.8 v6.what all is involved doing this??


Oil Pump

Removal


  1. If necessary, remove oil bypass filter (oil filter).
  2. Remove oil pump and filter body to engine front cover retaining bolts and remove oil pump and filter body from engine front cover.
  3. Inspect oil pump body seal (6C639), oil pump and filter body and engine front cover for distortion and wear. Replace components as necessary.
Installation

  1. Position oil pump and filter body on engine front cover and install retaining bolts.
  2. Tighten the small engine front cover retaining bolts to 8-11 Nm (71-97 lb-in) . Tighten the large retaining bolts to 23-32 Nm (17-23 lb-in) .
  3. If removed, reinstall oil bypass filter (oil filter).

Dec 04, 2009 | 1995 Ford Taurus

1 Answer

Changeing oil


on the right hand side of the motor is the cover for the oil filter. close to your brake pedal, after draining oil from the drain plug located under the motor, remove this cover take out and replace oil filter, put cover back on, be careful not to over tighten bolts, the strip easily. replace drain plug and fill with oil.... hey presto it's done. about 15 mins.....
http://www.stadiumyamaha.com/pages/parts/viewbybrand/parts.aspx

Mar 01, 2009 | 2001 Yamaha V Star 1100 Classic

Not finding what you are looking for?
2001 Suzuki GZ 250 Marauder Logo

Related Topics:

68 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4535 Answers

Richard
Richard

Level 2 Expert

83 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...