Question about Suzuki GSX-R 250 Motorcycles

1 Answer

It wont turn over with the switch...I tried to pull the pull cord and it wont move...I took the spark plug out and the starter and it still wont move.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 59 Answers

It has probably seized.

Posted on Mar 15, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Cant get it to turnover


if it wont allow one to pull starter cord out , or is very tight feeling , try taking out the spark plug and pulling it then, if still wont go , it looks like it may have been run without enough oil mixture , an will need to be rebuilt (if worth it ??) if saw does pull over easier but the chain moves too , then your clutch is too tight or may need to be free'd up some

Jan 24, 2016 | Garden

1 Answer

The starter pull cord on my gas trimmer will not pull.


Hi Mark
Perhaps a bit late now.... Just spotted this so I imagine it's all fixed by now.
But for others with this sort of problem.
Assuming the pull cord is not broken, stuck or tangled. Switch off or short plug to ground, for safety then remove the spark plug to allow the engine compression to escape. You should be able to turn the engine over really easy with the pull rope, otherwise the engine might be seized or the rotary pull mechanism jammed.
Also... can the shaft to the string line be rotated as in the crankshaft of the engine.
Good Luck

Aug 30, 2014 | Echo New String Trimmer SRM-225 2 Stroke...

1 Answer

Briggs and stratton 35 classic wont start, what can i do?


take the plug lead off and hold it near to some metal part on the mower, move the throttle lever to around midway and pull the mower cord, if there is a spark the electrical part of the mower is working.
remove the plug, put the lead back on the plug and earth the plug on a metal area and pull the cord again, if there is spark across the points on the plug then the plug is ok, if not replace the plug and try again.
assuming that the plug and lead checks out fine then check the fuel supply, remove the air filter from the side of the carbi and spray some fuel directly into the throat of the carbi and pull the starter cord, if the engine runs for a few seconds you can assume that you have a fuel problem, possibly the filter inside the fuel tank is clogged.

May 21, 2014 | Garden

1 Answer

1420 wont start


First I would check for spark. I have a spark checker that connects between the spark plug and the spark plug cable.The are found in the lawn mower parts section of department stores or home centers. With the ignition switch turned on pulling the starter cord and the spark is much more easy to see. Spray some starting fluid into the carb and if it fires the fuel has gone bad or the carb is plugged. How old is the fuel? If you don't know dump it out and and put fresh fuel in.

Nov 03, 2013 | Poulan Garden

1 Answer

I have a 2 year old Ryobi RY34440 String trimmer, 30cc. Last year worked fine, this year pull cord is so easy to pull it doesn't even turn engine over. Is is the spark plug?


Either the pull starter is not pulling or you are not getting compression. To check you need to check the spark plug is still snug. If so, remove the plug and put a drinking straw in the hole to touch the piston. Slowly pull the starter to see if the piston is moving. If the piston is moving and the plug was snug then you are losing compression somewhere, like a head gasket. If not moving then the problem most likely is in the starter, and disassembly required to investigate.

If really helpful, please rate.

Jul 12, 2011 | Ryobi Garden

1 Answer

Went to start bp251 blower after sitting in shed for a week, pull string was very hard to pull. took off plug a lot of fuel came out of plug hole . also checked muffler screen,was clean. there was quite a...


Take plug out turn blower to where plug hole is down pull starter cord many times until all fuel is out. Clean plug, install, try starting without priming or choking. If no start try priming just until you get fuel to engine. Try starting again. If this works when storing blower leave fuel cap slightly loose in very hot weather until you want to start.

Aug 09, 2017 | ECHO, Inc. PB-251C Handheld Blower

1 Answer

Troy bilt tuff cut 200. Will not started.. started fine the other day. pulling cord and will not turn over. already tried spraying starter fluid in carb... it is roughly a 2004


The first things you should check if your mower wont start is fuel, air and spark. Try pulling the cord a few times and then pull out the spark plug. If it looks wet then its getting fuel. Plug the spark plug into the wire while its outside the mower and hold it very close to a piece of metal attached to the engine without touching the metal (use insulated pliers). Have someone else pull the cord and see if you have sparks jumping between the plug and the engine. Also remove the air filter and clean it with gasoline if its made out of foam or buy a replacement if its made out of paper.

Let me know if none of these things work.

Jun 06, 2011 | Troy Garden

2 Answers

Crank pull cord doesn't pull out on honda pressure washer.. The machine is only 3 months old


if the fuel tap has been left on it may have fuel on top of the cylinder and would not able to pull cord.
if so take the spark plug out and turn over,fuel may come out of hole.replace spark plug and try to start. if it still won't turn over,you will need to take the face plate off the motor. remove and inspect if there is any foreign objects. try to turn motor over by hand., grab on to fly wheel & turn. if it moves freely it may be the pull start it-self. try pulling the cord out. if no problem assemble and try to start.

Dec 02, 2010 | Honda Pressure Washer PSI 3000

2 Answers

Petrol chainsaw wouldn't start, and with trying to get it running the pull cord is very very stiff to pull out and it is now just jurking small sections of the cord out at a time and still will not start


Sounds like it may have hydraulic lock--the upper cylinder is full of fuel. Remove the spark plug and pull the engine through a number of times. Make sure the ignition switch is off--it might ignite the expelled fuel. You may find that the crankcase is also full of fuel--continue to pull the starter until there is no raw fuel expelled. Now, why didn't it fire! Probable bad ignition system--check for firing of a clean spark plug (ignition on). If ok, try the original plug, it may need to be cleaned or replaced.

Jun 27, 2009 | Garden

1 Answer

Leaf blower


One suggestion, unscrew the spark plug and reconnect the high voltage wire. In a very dark area move the plug so that the plug thread touches some metal on the engine. Pull the starter cord. If you don't see a spark, remove the two screws on the handle and see if two wires are attached to the Stop Engine Switch. Remove one wire and bend it away from metal and try to see spark when pulling the start cord. If spark occurs, the Switch is shorted and needs replacing.

Oct 31, 2008 | Homelite 'Yard Broom' Leaf Blower

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

49 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4533 Answers

Richard
Richard

Level 2 Expert

83 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...