Question about 2002 Honda VF 750 C Magna

1 Answer

Removing front wheel on 2002 honda magna is the axle threaded and which thread right hand or left hand

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An user who is expert in 3 categories / brands.

  • Honda Master
  • 1,508 Answers

It will be right hand thread, so turn anticlockwise to loosen, if there is no axle nut, they can be threaded into the opposite fork leg.
Make sure any pinch bolts are loosened

Posted on Mar 16, 2011


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How do I remove the rear axle nut on a 2001 mazda MPV?

No, it would not be left hand threads. Just on super tight, probabvly torqued down to about 200 ft. lbs. Use a good stout breaker bar.

Aug 23, 2012 | 2001 Mazda MPV

1 Answer

Need to put bobin in a merritt 4530

Flip the presser switch up to raise the presser foot. Turn the hand wheel counterclockwise until the needle is in its highest position.
  • 2Hold the hand wheel in place with your left hand while turning the hand wheel knob counterclockwise with your right hand to loosen the hand wheel knob.
  • 3Place the desired spool of thread on the spool pin so that the pin fits all the way through the hole in the center of the spool. Put the spool holder onto the end of the spool pin that is sticking through the spool of thread and press firmly to ensure that the spool holder keeps the spool in place.
  • 4Grasp the end of the thread and hold it taut between the thumb and index fingers of both hands. Snap the taut section of thread into the thread guide post located to the left of the spool pin.
  • 5Pull the end of the thread gently. Wrap the thread around the bobbin winder tension disk near the left front on top of the machine, starting at the side of the tension disk facing you and wrapping around in a clockwise direction.
  • 6Poke the end of the thread through the small hole in the bobbin from the inside out so that the loose end of the thread sticks through the top of the bobbin. Put the bobbin on the spindle, or bobbin winder, and gently slide the bobbin winder to the right.
  • 7Hold the loose end of the thread in place while pressing down on the foot pedal to start the machine. Hold the foot pedal down until the bobbin is as full as desired. The machine will automatically stop once the bobbin has reached capacity.
  • 8Cut the loose end of the thread using scissors. Slide the bobbin winder to the left and remove the bobbin. Hold the hand wheel in your left hand and tighten the hand wheel knob with your right hand by turning it clockwise
  • Apr 05, 2012 | Singer 6510 Sewing Machine

    1 Answer

    Have an older Big Bear and cannot shift the front axle wheel nuts to get at the brake drums. Are they left and right hand threads respectively?


    Jul 19, 2011 | 1995 Yamaha YZF 750 R

    2 Answers

    How do I change a brush? I can't get the axle locked to get the nut off. Can you help me?

    Remember if you are trying to change the left side it is a reverse thread nut. You would turn it clockwise to loosen. IF it is very tight, put a wrench on both sides. IF the right side comes loose, remove brush/grinding wheel, and re-install nut, with an extra nut locked to the first one, the put a wrench on both sides again.

    Sep 30, 2010 | Sears Rockwell 8 in. 3/4 hp, 5-amp Bench...

    1 Answer

    Replace alternator

    Remove or disconnect the following:
    • Negative battery cable
    • Right front wheel
    • Right fender splash shield
    • Accessory drive belt
    NOTE The crankshaft pulley retainer has left-hand threads.

    • Crankshaft pulley
    • Alternator harness connectors
    • Alternator


    Remove the crankshaft pulley to provide clearance—2002–04 3.0L

    To install:
    1. Install or connect the following:
      • Alternator and tighten the fasteners to 18 ft. lbs. (25 Nm)
      • Alternator harness connectors
      NOTE The crankshaft pulley retainer has left-hand threads.

      • Crankshaft pulley and tighten to 74 ft. lbs. (100 Nm)
      • Accessory drive belt
      • Right fender splash shield
      • Right front wheel
      • Negative battery cable
    2. Start the engine and check for proper operation

    May 12, 2010 | 2003 Ford Taurus

    1 Answer

    Removing ZR7-s front wheel

    think usaualy the bolt goes allthe way through

    Jul 28, 2009 | 2002 kawasaki ZR-7 S

    Not finding what you are looking for?
    2002 Honda VF 750 C Magna Logo

    298 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Honda Experts

    Arnie Burke
    Arnie Burke

    Level 3 Expert

    4535 Answers


    Level 3 Expert

    76630 Answers


    Level 2 Expert

    342 Answers

    Are you a Honda Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides