Question about kawasaki ZX-6R Motorcycles

1 Answer

I want to lower my 03 636 how is this done - ZX-6R kawasaki Motorcycles

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 59 Answers

You can purchase lowering links for the rear and slide the front shock tubes up in the tipple tree.
The lowering links will come with an installation diagram and to slide the shock tubes up simply loosen the 4 bolts (per tube) and slide them up until you reach the desired ride height.

Posted on Mar 15, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to loosen saw on rockwell motorized miter box


To 'raise/lower' the saw, pull out the knob near the back hinge. It helps if you lightly push down on the saw-handle which is spring loaded. The knob should pull out to allow the saw to lift.

To swing the saw left and right, unscrew the lock bolt (at the lower handle) but just one full turn or so. Under it there is a catch you can lift, it works like a tab and stops at the frequently used cuts (like 45-degrees).

When done, push the saw back into the lowered position and push in on the knob mentioned at the first line. Done!

Sep 30, 2017 | Saws

1 Answer

Left front lower control arm broken in 2004 Honda Civic Hybrid


i would replace it, not easily done you need special tools

Feb 13, 2014 | 1993 Chevrolet C1500

1 Answer

Jaguar X Type lower in front


What issue?
Lower in front of what,than what ?
What is the question,what changed
since you owned it?

Jul 28, 2013 | 2002 Jaguar X-Type

1 Answer

05 jeep liberty -rear recall done by dealer,,, alignment ,,,jeep drifs to the right


take it back to the dealer and have them check for correct installation of the recall
it is necessary to align the rear of a vehicle before the front is done or you will get "crabbing" which is what you describe
any work on the rear suspension will require that the rear be aligned first

Jun 04, 2017 | 2005 Jeep Liberty

1 Answer

Done outside gummy inside


Hi.
I'm guessing that this is a cooking problem, so here goes.

If the food your cooking is done on the outside, but not done on the inside, then you have the temperature at the wrong settings.

Reduce to a lower temp, try with a new batch, and cook it for 50% longer at the lower temp: i.e. if it said 350 degrees for 30 minutes, then reduce to 300 and cook it for 45 minutes instead.

The longer time allows for the heat to penetrate and cook the middle, not just the outside.

I hope this helps you out, and good luck.

Mar 14, 2011 | Computers & Internet

2 Answers

How can i lower the height of the bike i am on my tip toes


Only two ways you can acheive this. the first is to have your rear suspension modified, or lowered by about an inch should do it. This job would most likely have to be done at a mechanics shop. But is possible.
The second solution, involves lowering your seat height, by cutting about an inch or so of foam off the top of the seat. This job is also best done by an upholsterer, but is a possible aternative to lowering the suspension, get your seat chopped down.

Jun 21, 2010 | 2003 Suzuki AN 650 Burgman

2 Answers

Excesive inside edge front worn tires.


have an alignment done. the technician should check for a bad suspension component before the alignment is done to ensure it is done correctly. make sure you inform him you would like to know of any suspension prats that need replacing

Jun 09, 2010 | 1990 Honda Civic

1 Answer

Lower ds screen lights up and touch works but no picture?


Hello!

There are 2 things that may need to be done.

1.) Replace the lower LCD screen
2.) Replace the motherboard

Sometimes the motherboard causes problems with either the Upper or Lower LCD.

But, I would change the lower first.

There are websites on the internet that will show you how to do this.

Or , you could send it in for repair.

Dec 29, 2009 | Nintendo DS Lite Console

2 Answers

How to lower the st1100


have your local honda dealer do it so that it can be done properly. only other suggestion is to dial up the rear shock preload and lower the fork tubes in the steering stem.

Oct 03, 2009 | 2001 Honda ST 1100 Pan European (cbs-abs...

1 Answer

I NEED DETAILS ON LOWERING MY BIKE.


If you bought the lowering links they get installed down at the counter lever on the rear shock,also suggest you lower the frt fork tubes by makeing the tubes stick up past the triple tree 1 inch this will help with thr rake of the bike after you lower the rear and keep it from getting wobbly in the coners.

Mar 31, 2009 | 2008 kawasaki ZX-10R

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

135 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4818 Answers

yadayada
yadayada

Level 3 Expert

78919 Answers

bazzz7071
bazzz7071

Level 2 Expert

342 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...