Question about 2007 kawasaki ZX-10R

1 Answer

I instaled new clutch plates in my zx10 and I don't have any motion

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Master
  • 1,591 Answers

Excuse the silly question, but do you by any chance have any springs laying around the shop floor that you maybe forgot to put back in?
The other possibility is your clutch cable is too tight and needs to be backed off, or is simply incorrectly seated.

Posted on Mar 15, 2011


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How do i get the sparkplugs out of a 2004 zx10

First you remove the plug wire by pulling on the boot, not the wire. Next you need either a 5/8 or 13/16 deep well 3/8 socket and ratchet. You will use a counter clockwise motion to remove the spark plug and a clockwise motion to install a replacement spark plug. Spark plugs should be tightened snugly and not over tightened.

Oct 06, 2012 | kawasaki Motorcycles

1 Answer

Why when I install new clutches on a 04 zx10? my clutch cable has to much slack in line?

Hi Javiscannon, you need to do a proper clutch adjustment, for more information about your question please visit the website below. Good luck and have a nice day.
1990 Kawasaki Motorcycle Service Repair Workshop Manuals

May 05, 2012 | 1990 kawasaki ZX 10

1 Answer

How do I replace a clutch 2000 eclipse

Remove transaxle. Remove clutch pressure plate. Remove clutch plate. Inspect the flywheel for damage and resurface or replace as necessary. Replace pilot and throwout bearings. Install new clutch plate. Install new pressure plate. Re-install transaxle.

Mar 06, 2012 | 2000 Mitsubishi Eclipse

1 Answer

Motorcycle engine slipping wih new clutch plates and cable

Is the pressure plate (springs) ok? New discs will not work if they don't have enough pressure on them. Do you have any free movement of the clutch at the handlebars, before you feel pressure? Maybe you just need to adjust your clutch cable.

Feb 09, 2012 | Motorcycles

1 Answer

Hi, I have a 2006 zx10 and I had a bent clutch rod after changing a broken clutch lever, so after installing the new one and the clutch is hooked up when i start the bike and pull the clutch in dropping...

You may have a kick stand switch which will kill the bike if you try to ride off with it down, The switch on the clutch lever is so you cannot start the bike in gear unless its in neutral. There should also be a switch that goes in the transmission that works along with the other switch(es).
If at least one of these has a fault then that may be your issue.

Look at the clutch lever switch closely. Sometimes they have a small pin that the lever touches. If that small pin broke off then the lever cannot make contact.
then look around the trans since you were in there changing a rod.

Aug 31, 2011 | 2006 kawasaki Ninja ZX10 R

1 Answer

206 w reg fitted new clutch but now have no biting point so car will not pull away help

Hello, Who installed the clutch"? Were there a new pressure plate installed? Were there a new throw out bearing installed. Does this 1991 Peugeot 405 have hydraulic or mechanical clutch linkage?
There a couple of reason why the Peugeot wont move and engine is running and the transmission is in gear.

1.. Pressure plate is installed backwards.--Remove transmission and reinstall pressure plate in the correct orientation to the clutch. There is two ways to install it, but one way correctly.

2. Adjustment for the clutch linkage from the pedal in the driver compartment is adjusted to tight and not releasing the clutch to where the clutch pressure is on the pressure plate.

I hope this helps. GB....stewbison

Aug 24, 2011 | 1991 Peugeot 405

1 Answer

Just replaced the clutch in an '88 ZX10 how do u

Thrue the clutch cable and the adjuster nut thare at the clutch hub... Adjust the one at the clutch hub first then take up slack at the handle ..

May 30, 2011 | 1988 kawasaki ZX 10

1 Answer

I have a 2005 XR 650L, and the clutch quit working. I have adjusted the cable and am getting full range of motion, its just not dis engaging the clutch. it has 2000 miles and has not been ridden hard at...

with 2000 miles you should not be having a issue like you state , if your cable is not seized and good working order the clutch should work, if not when you had the clutch apart did you lightly sand the metal and fiber plates also when you install the clutch hub make sure it's seated correct or the clutch will not work, the plates must be tight in the clutch hub also check the online parts diagram to make sure no parts are missing , also check that hub is not grooved from wear.

Jan 24, 2018 | 2001 Honda XR 650 R

1 Answer

Grabby clutch in 1st.

I'll bet you replaced the "fiber" plates only in which case you need to either take the steel plated out and have them sand blasted, or preferably "glass beaded", you have a hot spot on one of the plates which is causing the clutch to be "grabby" also not sure if you replaced the clutch springs but if you did and they are after market they may be to high of spring pressure.
Did you install a stock clutch or a after market one? Many times the after market hi-performance clutches are made with aluminum plates and then they add the fiber and the clutch will chatter because the engine HP to to substantial for the aluminum to handle. I highly recommend using the stock Yamaha clutch plates and springs. They are of the highest quality and are the best to use.
Please let me know what type of plates you are running and I'll work from there with you. Also if you cannot get the plates blasted you can take them out and rough them up on your garage floor. Your want to use even pressure and move in a circular motion to scratch them up. Make sure you clean them afterward in mineral spirits. You can buy that at any paint store real cheap.
Good Luck,

Dec 12, 2008 | 2002 Yamaha YZ 426 F

Not finding what you are looking for?
2007 kawasaki ZX-10R Logo

Related Topics:

430 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4825 Answers


Level 3 Expert

79186 Answers


Level 2 Expert

342 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides