Question about Honda CR 125 R Motorcycles

1 Answer

My 2001 cr125r wont start after going thru water what can it be. it us to start one or two kicks the most

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert who has answered 20 questions.


    An expert that has over 10 points.


    An expert whose answer got voted for 2 times.

  • Expert
  • 55 Answers

It may be that the spark plugs have water in them. Try removing the spark plugs and checking for moisture there. Usually if you let it dry under the sun for a few hours it should get back to normal.

Posted on Mar 13, 2011


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

99 chev wont go into kick down mode but

unless there is a situation where the engine rpm falls below required that to drive the gear box then there will be no kick down . Check and carry out the correct adjustment for the kick down system

Jan 07, 2014 | 2002 Chevrolet Silverado 1500

1 Answer

Over heating 2001 Mercury Cougar 2.5 manual

is it losing water? if not is your fan kicking on? if losing water, place piece of cardboard under veh at night to help pinpoint where water is leaking. if not losing water and fan does'nt come on check fan relay. if loses water and don't see leak over night on cardboard, then water pump is leaking thru weep hole but only after heats up and pressure is on need to replace water pump.

Aug 28, 2012 | 2001 Mercury Cougar

1 Answer

Went to start the 2001 s-10 i let go of the key to quick acts like the anti-theft kicked in..gas shut down and egnishtion wont kick on... get all the right lights just wont try to turn over...what can i do...

hi there
you can actually dis connect the positive side of the battery keep disconnected for one min then reconnect this will reset the computer in the vehicle and should put you back on the road have a wonderful thank you

Aug 22, 2011 | 2001 Chevrolet S-10

1 Answer

Replaced thermostat, cleaned heating coil still wont blow hot air in 2001 sble

is heater core have water flowing thru it ? if take haeter hoses loose at engine run water thru one hose see if flowing out the other one

Nov 02, 2010 | 2001 Mercury Sable

1 Answer

My kick start sticks when im kicking it over why?

the spring on the other side has cam loose and its not springing back.
Your manaul will tell you how to inspect and replace it.
I've seen it a bunch. Usually comes loose when the spring is worn and you kick it real fast, and the spring pops off.

Oct 01, 2010 | Clymer Honda Cr125R 19921997 Cr250R...

2 Answers

Water leak right side kickpanel when it rains water runs down right side kick panel runs through door tray.

check seals around the door and the body where door closes, also check where windshield ends and firewall starts, could be small leak around any hoses or lines that go thru firewall, such as heater hoses and screw holes where parts are attached

Feb 12, 2010 | 2001 Ford F350 Super Duty SuperCab

1 Answer

I have a 1991 cr250 wont start it has compression ,spark and gas to carb?? feels like it wants to kick over.problem started with having gas going thru carb was flooding , completely cleaned carb now wont...

just adjust the accelerator cable that is connecting to the fuel pump.check the and repair the throttle cause its the reason why it wont start . Its flooding the because of too much release of gas to the carb.

Jul 28, 2009 | Honda CR 250 R Motorcycles

1 Answer

Cr125r 2001 cant start after changing piston and cylinder

hi mate you need to adjust the float if theres to much fuel going through you need to take the float out and adjust it to the manual specifications but remember slot the pin out and take the float out but watch the little valve which stops the fuel where the little valve is hanging from that is the part you need to adjust

Jul 20, 2009 | 2002 Honda CR 125 R

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

68 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4988 Answers


Level 3 Expert

80407 Answers


Level 2 Expert

342 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides