Question about Honda CG 150 Titan KS Motorcycles

2 Answers

Wot is the twin cable on the carburetor for - CG 150 Titan KS Honda Motorcycles

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 403 Answers

What exactly are we dealing with. but it should be 1 for throttle, and 1 for choke.

Posted on Mar 13, 2011

  • Mark Mar 20, 2011

    yes

×

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,978 Answers

On the vacuum style Keihin carburetors one cable opens the throttle and the second cable drops the carburetor back to an idle. If you do not have the second cable attached your engine will stay revved up and drop back to an idle very slowly. It is hard to shift and to basically drive the bike in a safe manner when the engine stays at a high rev every time you twist or back off on the throttle.

Posted on Mar 13, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1986 Yamaha xv750 virago acts like running on one cylinder at times


Hi, Anonymous and the usual suspects are:
1. Severely discharged or a damaged battery, should have 12.5 volts or better and be able to pass a load test if necessary.
2. Check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
3. Spark plugs in bad condition or partially fouled.
4. Spark plug cables in bad condition and leaking check for spark leakage in the dark
5. Spark plug gap too close or too wide.
6. Faulty ignition coil, module, and or sensor.
7. Loose, dirty, or corroded ignition module connector at crankcase.
8. Faulty CKP or CMP, MAP, ETS, ATS, TPS, O2 sensor.
9. Dirty air filter.
10. Intake air leak.
11. Water, dirt, or rust in the fuel system, carburetor and/or filter.
12. Old dead or bad fuel.
13. Fuel tank vent system plugged or carburetor vent line closed off.
14. Vacuum line from intake manifold to fuel valve is broken, cracked, pinched, or missing.
15. Carburetor controls misadjusted.
16. Damaged carburetor.
17. Incorrect valve timing.
18. Weak or broken valve springs.
19. Damaged intake or exhaust valve.
20. Check for engine trouble codes
For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have nice a day.
Probable Solution to the Firing on One Cylinder Issue 50MPH at WOT No More
ViragoTechForum com
1981 1994 Yamaha XV Twin Service Manual Moto Data Project
OEM parts for Yamaha
http://mybikemanuals.com/yamaha/yamaha-xv-owners-manuals

Mar 29, 2014 | 1988 Yamaha XV 535 Virago DX

1 Answer

2002 harley twin cam efi backfires through intake


Hi Anonymous, and the usual suspects are:
1. Spark plugs in bad condition or partially fouled.
2. Spark plug cables in bad condition or leaking.
3. Spark plug gap to close or to wide.
4. Faulty ignition coil, module and or sensor.
5. Battery nearly discharged.
6. Damaged wire or loose connections at battery terminals,
ignition coil, or plug between ignition sensor and module.
7. Intermittent short circuit due to damaged wire insulation.
8. Water or dirt in fuel system, carburetor or filter.
9. Fuel tank vent system plugged or carburetor vent line closed off.
10. Carburetor controls misadjusted.
11. Damaged carburetor.
12. Loose or dirty ignition module connector at crankcase.
13. Faulty MAP, CKP, and or CMP sensors.
14. Incorrect valve timing.
15. Weak or broken valve springs.
16. Damage intake or exhaust vale.
For a prime suspect please visit website below and good luck:
Big Twin Carb EFI DTC Intructions codes Harley Davidson Forums Harley...

Dec 02, 2013 | Harley Davidson Motorcycles

1 Answer

Not getting gas carburetor


have you looked at where the carb is ? wots in front of it ? wots connected to it ? hows it held to the intake ? if youve answered these Questions then still dont know what to do then take it to a bike mechanic !!

Dec 01, 2013 | Yamaha Road Star Midnight Motorcycles

1 Answer

Missing backfiring


Hi Anonymous, and the usual suspects are:
1. Spark plugs in bad condition or partially fouled.
2. Spark plug cables in bad condition or leaking.
3. Spark plug gap to close or to wide.
4. Faulty ignition coil, module and or sensor.
5. Battery nearly discharged.
6. Damaged wire or loose connections at battery terminals especially the ground cable at BOTH ends, ignition coil, or plug between ignition sensor and module.
7. Intermittent short circuit due to damaged wire insulation.
8. Water or dirt in fuel system, carburetor or filter.
9. Fuel tank vent system plugged or carburetor vent line closed off.
10. Carburetor controls misadjusted.
11. Damaged carburetor.
12. Loose or dirty ignition module connector at crankcase.
13. Faulty MAP, CKP, and or CMP sensors.
14. Incorrect valve timing.
15. Weak or broken valve springs.
16. Damage intake or exhaust valve.
For a prime suspect please visit website below and good luck:
Big Twin Carb EFI DTC Intructions codes Harley Davidson Forums Harley...

Jul 08, 2013 | Harley Davidson Motorcycles

1 Answer

One cylinder runs cold


Hi Jim, and the usual suspects are:
1. Spark plugs in bad condition or partially fouled.
2. Spark plug cables in bad condition or leaking.
3. Spark plug gap to close or to wide.
4. Faulty ignition coil, module and or sensor.
5. Battery nearly discharged.
6. Damaged wire or loose connections at battery terminals especially the ground cable at BOTH ends, ignition coil, or plug between ignition sensor and module.
7. Intermittent short circuit due to damaged wire insulation.
8. Water or dirt in fuel system, carburetor or filter.
9. Fuel tank vent system plugged or carburetor vent line closed off.
10. Carburetor controls misadjusted.
11. Damaged carburetor.
12. Loose or dirty ignition module connector at crankcase.
13. Faulty MAP, CKP, and or CMP sensors.
14. Incorrect valve timing.
15. Weak or broken valve springs.
16. Damage intake or exhaust valve.
For a prime suspect please visit website below and good luck:
Big Twin Carb EFI DTC Intructions codes Harley Davidson Forums Harley...

Apr 22, 2013 | Harley Davidson FXR Super Glide...

1 Answer

2000 fat boy runs rough backfires smell gas


Hi Anonymous, and the usual suspects are:
1. Spark plugs in bad condition or partially fouled.
2. Spark plug cables in bad condition or leaking.
3. Spark plug gap to close or to wide.
4. Faulty ignition coil, module and or sensor.
5. Battery nearly discharged.
6. Damaged wire or loose connections at battery terminals especially the ground cable at BOTH ends, ignition coil, or plug between ignition sensor and module.
7. Intermittent short circuit due to damaged wire insulation.
8. Water or dirt in fuel system, carburetor or filter.
9. Fuel tank vent system plugged or carburetor vent line closed off.
10. Carburetor controls misadjusted.
11. Damaged carburetor.
12. Loose or dirty ignition module connector at crankcase.
13. Faulty MAP, CKP, and or CMP sensors.
14. Incorrect valve timing.
15. Weak or broken valve springs.
16. Damage intake or exhaust valve.
For a prime suspect please visit website below and good luck:
Big Twin Carb EFI DTC Intructions codes Harley Davidson Forums Harley...

Apr 12, 2013 | Harley Davidson Motorcycles

1 Answer

02 ultra classic losses power under load


Hi Martin, and the usual suspects are:
1. Spark plugs in bad condition or partially fouled.
2. Spark plug cables in bad condition or leaking.
3. Spark plug gap to close or to wide.
4. Faulty ignition coil, module and or sensor.
5. Battery nearly discharged.
6. Damaged wire or loose connections at battery terminals,
ignition coil, or plug between ignition sensor and module.
7. Intermittent short circuit due to damaged wire insulation.
8. Water or dirt in fuel system, carburetor or filter.
9. Fuel tank vent system plugged or carburetor vent line closed off.
10. Carburetor controls misadjusted.
11. Damaged carburetor.
12. Loose or dirty ignition module connector at crankcase.
13. Faulty MAP, CKP, and or CMP sensors.
14. Incorrect valve timing.
15. Weak or broken valve springs.
16. Damage intake or exhaust vale.
For a prime suspect please visit website below and good luck:
Big Twin Carb EFI DTC Intructions codes Harley Davidson Forums Harley...

Jul 09, 2012 | 2000 Harley Davidson FLHTCUI Electra Glide...

1 Answer

Where is the carb on a jeep grand cherokee 1993 4.0 liter


There is no carburetor on any of the 6 cylinder or 8 cylinder Jeep Grand Cherokees. They have Fuel Injection and a throttle body which looks like a carburetor scaled down.

---
Instructions on how to remove and replace the throttle body follow:

Throttle Body REMOVAL & INSTALLATION
  1. Disconnect the negative battery cable.
  2. Remove the vacuum hoses from upper bonnet, unfasten the retaining clips and remove the upper bonnet assembly.
  3. Remove the lower bonnet retaining bolts and lower bonnet.
  4. Remove the throttle cable and the return spring.
  5. Disengage the wire harness connector from the injector.
  6. Disengage the wire harness connector from the WOT switch, ISA motor and TPS.
  7. Disconnect the fuel supply and return lines from the throttle body.
  8. Tag and disengage the vacuum hoses from the throttle body assembly.
  9. Disengage the potentiometer wire connector.
  10. Loosen throttle body retaining bolts and remove throttle body assembly from the intake manifold. To install:
  11. Clean the intake manifold and throttle body mating surfaces of old gasket material.
  12. Install a new gasket and the throttle body assembly. Tighten the mounting bolts to 16 ft. lbs. (21 Nm).
  13. Engage the potentiometer wire connector.
  14. Engage the vacuum hoses to the throttle body.
  15. Engage the fuel lines to the throttle body.
  16. Engage the WOT switch, ISA motor, TPS, and injector electrical connections.
  17. Install the return spring and throttle cable.
  18. Install the lower bonnet and fasten the retainers.
  19. Install the upper bonnet assembly, retaining clips and vacuum hoses.
  20. Connect the negative battery cable.
  21. Start the vehicle and check for fuel leaks. Fig. 1: Exploded view of the throttle body and related components 86745g41.gif
prev.gif next.gif

Aug 17, 2010 | 1993 Jeep Grand Cherokee

2 Answers

Gas peddle sticks


Most gas pedal is connected to the carburetor by a 1/8 or 1/16 inch cable to control the gas entering the combustion chamber of the engine. When this get stucked due to wear, it is high time to get a replacement Accelerator Cable for Toyota 1992 4 Runner. Get this done, and send your e-mail comments.

Oct 05, 2009 | 1992 Toyota 4Runner

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

212 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4521 Answers

yadayada
yadayada

Level 3 Expert

76070 Answers

Mike

Level 3 Expert

4339 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...