Question about 1980 Laverda 1000 Jota

1 Answer

Having problems with clutch ajustment of laverda 1980 model... please help

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 7 Answers

Jo - you need to explain what problems you are having!! The 1980 model had a cable operated mechanism. Vital that the clutch cable is smoothly routed with bends as big a radius as possible. Lubrication of clutch lever pivot and cable is vital too. Handlebar adjuster should be used to leave a small amount of slack. If the problem is getting the clutch to free off, then if the bike has been standing for a long time the plates can stick together. Have an answer for that...

Posted on Mar 11, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 1980 VW Golf. I cannot get reverse gear or 1st and 2nd without switching the car off and then selecting the gear? 3rd and 4th works fine.please help


hydraulic clutch needs attention
replace slave cylinder fill with fluid and bleed the air out
replacing the clutch master cylinder would also be a good idea as at 1980 model will be worn out if not replaced before hand
if cable clutch , replace the cable

Aug 22, 2016 | Volkswagen Golf Cars & Trucks

1 Answer

How do I adjust a 1996 Mazda 121's clutch cable please?


Hi im not familer with this model,but if it is a cable the adjustment will be where the cable gose into the gearbox bellhousing,if there is not a ajuster there then it could be that the clutch pedle has a ratchet that selth ajusts as the clutch wheres down wich means im sorry to say you will need a new clutch,best of luck I hope its the first one.

Aug 08, 2015 | Mazda Cars & Trucks

1 Answer

Sticking clutch plates


Be sure you are using the correct weight of engine oil. Too heavy a viscosity will cause the problem you mention. In addition, it could be the clutch cable sticking rather than the plates. Have you lubricated that cable lately? Does anyone even do that any more?

Mar 31, 2014 | Laverda 1000 Jota Motorcycles

1 Answer

Clutch problems


Need more info.No clutch actuation? Slipping? What's it doing or not doing?

Oct 02, 2013 | Laverda 1000 Jota Motorcycles

1 Answer

Laverda Mirage


Sterling Silver 244 (BMW) shade number 1 Dupont

Jul 30, 2010 | 1980 Laverda 1000 Jota

2 Answers

I own a 2003 laverda 750S. I battle to get it started, the starter battles to turn the motor!!


how good is the battery check terminals are clean leads and all conections are good try remote battery and jump start it like a car if the problem goes away its your battery if not its the starter or solinoid or leads

Jun 23, 2010 | 1971 Laverda 750 S

1 Answer

After traveling about 8km my car wont go into 1st or reverse gear. when it is cold it goes into all the gears fine. when i switch the car off it will go into gear. we did put a new(aftermarket clutch) in a...


Cluth cable ajustment if equiped.Some cars have a cluth cylender if your model has the cylender no ajustment is available.If you had your cluth changed at a garage you might consider takeing it back in for ajustments.If you changed the clutch check cluth cable for ajustment if your car is equiped with cable if not i would perhaps remove the transmission and inspect clutch for loose clutch plate or release bearing might not be seated properly hope this helped you.

Dec 24, 2009 | Mazda 323 Cars & Trucks

1 Answer

I have a 1980 suzuki gs1000 g. clutch?


Drain the oil and install a new oil filter. Dirty, gritty oil can make a clutch act this way. After the oil change , ride the bike for an hour or so. Now drain the oil a second time. Doing this will flush most all of the grit from the engine.

FYI > Go to this site and you can download a free PDF service manual.
www.carlsalter.com/motorcycle-manuals.asp Most all of the manuals are in English.3bed404.gif

FYI > Go to the site below where you can see a parts diagram for your specific bike. You will select the actual brand, year, model, etc., once you go to the site. Part numbers and prices are also shown. You can order parts from this site. In the event no price is shown on a particular part, the part is not in stock. www.babbittsonline.com/pages/parts/viewbybrandand/parts.aspx

A “very helpful” rating for this answer? Thanks!

Jun 30, 2009 | 1980 Suzuki GS 750 L

1 Answer

Hi i have a saab 900 T, year 1980. the car do want GO


Yes your clutch assembly is gone.Without any second thought visit your garrage and get replaced along with the gear oil............sodeep

May 15, 2009 | 1983 Saab 900

1 Answer

Jota primary chain


is anyone able to confirm this as it looks a little fragile. You sometimes find 2 single chains on Laverda twins and triples. I never heard that Laverda used them instead of the triple chain to cope with any problems. The version I've heard is that the triple chain has not been available for some years. Therefore the 2 single chains were used. Though I never heard of the 2 single chains crashing i personally prefer the triple version. ,,

Nov 10, 2008 | 1982 Laverda 1000 Jota

Not finding what you are looking for?
1980 Laverda 1000 Jota Logo

219 people viewed this question

Ask a Question

Usually answered in minutes!

Top Laverda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers

Gil Davis

Level 2 Expert

156 Answers

Rigger

Level 3 Expert

1385 Answers

Are you a Laverda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...