Question about 2006 Yamaha SR 400

1 Answer

Front diff is not engaging, why? - 2006 Yamaha SR 400

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 114 Answers

This is just to make bike mechanics laugh, right? Thanks, I needed one.

Posted on Jan 04, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Diff locks not engaging on 80 series landcruiser


I think these actuators depend on vaccuum, check that all the hoses are in place and intact, could also be the vaccuum pump.

Jan 28, 2014 | 1991 Toyota Land Cruiser

1 Answer

Have 2003 f150 4wd light on but will not lock in


IF you have both front wheels in the air then either wheel will spin freely unless you have diff lock or limited slip diff. That is the nature of a diff..wd means that all 4 wheels drive but only when you have a limited slip diff or a diff locker. in action . If you have both of one side wheels in a bog you will not go any where.

Jan 05, 2014 | Cars & Trucks

1 Answer

2001 Toyota sequioa won't engage 4wd


For your four wheel drive to engage, the front diff actuator has to go into 4wd and then sends confirmation to 4wd ecu which in turn engages ur transfer case (center lock) If frame was just replaced, i check the connector on top of your front diff and make sure its plugged in as this would be a definite cause. Let me know how you go.

Dec 09, 2013 | 2001 Toyota Sequoia

1 Answer

My 4 wheel drive sounds like its engaging but front wheels not pulling.


the acutator on the front diff. might not be working even though its engaging in the trans for the gear ratio it still sounds like its not engaging in the front diff.

Dec 23, 2010 | Dodge Ram 1500 Cars & Trucks

1 Answer

How do i manually engage the front differential on 1991 s10? the transfar case engages but the front diff. doesnt


there should be a diaphram under the battery that connects to a cable this is vacuum operated but you can also pull back on to engage the front diff.

Nov 20, 2010 | 1991 Chevrolet S-10

1 Answer

Front diff not engaging transfer case operates corectly front diff isnt engaging has power and ground


check your u-joint at the transfer case and front of drive shaft they me be worn
also check the electrical connections underneath

Jan 29, 2010 | 1997 Chevrolet Tahoe

1 Answer

Front end does not engage in 4-wheel drive


The front diff in this model requires air pressure to engage. There is an electric pump for this purpose and once the pressure rises and remains where it's meant to, the pump shuts off and the dash light indicating 4WD will remain lit. It is sealed. There should be no leaks. If there is air coming out the top, do you mean out of the diff breather pipe? (The diff breather should be connected to a hose that goes up and is clipped next to the radiator.) If it is coming out of the diff breather, you have a punctured (worn out) diff engaging diaphragm which can only be replaced by stripping the diff casing.

Jun 11, 2009 | 2001 Suzuki Vitara

2 Answers

2002 grand vitara v6, will not engage 4x4, (no front axle activity) no activity light, tried 4-hi, and 4-lo, switches on t-case show shift rail activity, dont have a schematic to trace diff pump behind...


I had the same problem on Fraser Island over the Australia Day weekend. The problem was the rubber vacuum hose connected the front diff. There is a metal pipe than comes from the vacuum pump and along the lower engine cross member facing the front of the car. In my case the sand had dislodged the pipe which it turned dislodged the rubber vacuum hose connected from the pipe to the rear top of the front diff housing. This hose engages the front diff / hubs - if they don't engage the 4x4 green light won't come on. After reconnecting the rubber hose everything worked perfectly.

Hope this helps.
Cheers

Jan 07, 2009 | 2003 Suzuki Grand Vitara

1 Answer

Chevy Tahoe 2001


Place vehicle in 4wd (high or low). This will hold the front drive shaft still for the rest of the test. Jack up the front end of the vehicle. Remove the actuator. Have a buddy spin the right front wheel while you use a long punch or screwdriver to try to manually engage the diff. The left front wheel should spin in the other direction if the diff is good. Also before you check the diff you need to grab the front driveshaft and make sure it is locked, If it spins freely when the truck is in park and in 4wd with the front end raised then problem is in transfer case. If you can't make the diff engage manually with punch then the problem is in the diff. If front diff engages manually then the problem is the actuator. Hope this helps..

Nov 25, 2008 | Chevrolet Tracker Cars & Trucks

Not finding what you are looking for?
2006 Yamaha SR 400 Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Experts

dhnguyen

Level 2 Expert

281 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1144 Answers

Tony

Level 3 Expert

2600 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...