Question about 2005 Honda Activa

1 Answer

Always overflue carburator - 2005 Honda Activa

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 8,909 Answers

If you contact a Honda Motorcycle agent and request a float and needle valve for the carburettor, replacing those will cure the overflow problem. You may have to remove the carb. to work on it but it is a straight forward job.

Posted on Jan 03, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Outboard troubleshooting. I have a 75 hp Mercury with 2 carbuerators. Serial # 6559142 it's around a 1989 model.. Problem= tank bubble pumps up tight...sits for a minute and gets soft...when I pump it up...


Sounds like the fuel pump isn't working, you can buy service kits though quite often corrosion will prevent you from removing the valves.. or it could simply be the fuel cap isn't venting, remove fuel cap and see if the engine continues to run!

Mar 18, 2017 | Boating

3 Answers

Carburator and idle problem


Believe it or not you just said the solution to your own problem manufacturers specs requires for any adjustments to engine idle or other carburator adjustments to be preformed while the engine is idling and at normal operating temp in plain english let the car warm up then make your idle and mixture adjustments if this doesnt solve it i would check the auto choke and make sure it is opening at normal operating temp hope this helps good luck

Sep 01, 2008 | 1984 Toyota Tercel

2 Answers

86 ford escort with carberator dies at stop


If the problem is not a vac leak, it could be the idle circuit inside the carb. You may have to replace or rebuild the carb to fix it.

Jul 07, 2013 | Cars & Trucks

2 Answers

From where i can get the o ring & jet for carburator of my pulsar 150 dtsi -2005 model


you can go to an authorised delear of bajaj or you can find in the market. always use branded genuine parts manufactured by bosch germany or that sold my dealers. if you do not get it any where you con change the carburator of your bike.....

Jan 27, 2011 | 2005 Bajaj Pulsar 150

1 Answer

I have a scotts model 22965x8a lawn mower that conks out soon after starting. I have replaced the spark plug and cleaned the fuel lines but the problem persists. Any ideas for troubleshooting since I do...


Sounds to me like it is fuel related have you cleaned the carburator and Bowl ?
If not I would try removing the float bowl bolt located under the carburator .
these bolts are hollow and fill up with dirt and sediment once removed you will see small holes drilled into the side i use a torch tip cleaner but a straight pin will work to unclog .clean any debree from inside of bolt before installing i use spray carb cleaner with the extension will get into the holes well .I would always try this first before assuming the carburator needed to be taken apart and cleaned hope this helps .

May 21, 2010 | Garden

1 Answer

I have a 2006 Kawasaki Bayou 250 it is always fowling spark


does it backfire when revving down? are your spark plugs coming out black? if yes, you need to lean out your system a little by adjusting the mixture screw on the carb.

May 13, 2010 | Motorcycles

1 Answer

What is the float adjustment on a 1991 fxrs low rider convertible


Is the carburator a stock Kiehen or some other aftermarket carb? If it's a stock Kiehen, the float must be set with the carburator on an angle. If it's an S&S carb, the float level is 1/8" below the top edge of the float bowl. If you have a stock Kiehen, repost and I'll be more specific on how to set the float. I don't have my book with me at the moment and I don't want to tell you something incorrect. My memory ain't what it used to be and I always look at the book these days.

Oct 03, 2009 | 1993 Harley Davidson FXR Super Glide

1 Answer

Greetings, my nmae is Tim and I need some troubleshooting assistance with my Huskee GT (26 hp Briggs and Stratton ELS OHV eigine). The problem first became noticable about a month ago. When the mower had...


Check for an air leak around the intake and carburator mounting area. Also don't forget to check your fuel cap to make sure that it is vented properly. A cap that is not vented properly will not allow fuel to flow between the fuel tank and the carburator. These are a couple of areas that I would look at first. Hope this helps and good luck.

Jun 24, 2009 | Garden

Not finding what you are looking for?
2005 Honda Activa Logo

Related Topics:

105 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4521 Answers

yadayada
yadayada

Level 3 Expert

76164 Answers

Mike

Level 3 Expert

4340 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...