Question about Sym Husky 125 Motorcycles

1 Answer

Where would i find the regulator - Husky 125 Sym Motorcycles

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 13 Answers

If it is a SYM scooter, it could be anywhere. Under the front cover, under the floorboard, or under the seat pan. It is usually a small box, about the size of a deck of cards, and it will usually have heat sinks/fins molded into it. Call your local SYM dealer with the exact model you have and they should be able to tell you exactly where it is located. We sell KYMCO and our manuals tell us where to find all the parts on the bike. SYM's should as well. www.solanocycle.com

Posted on Jan 03, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need Instructions on replacing fuel regulator on 1987 chevys10 pick up 2.8


Fuel Pressure Regulator - REMOVAL & INSTALLATION(see Figures 1, 2, 3, 4, 5 and 6)
  1. Relieve fuel system pressure. Disconnect the negative battery cable.
  2. Clean dirt and grease from the regulator retaining ring.
  3. If equipped with a bolt on-type pressure regulator, remove the fuel return line from the return tube by squeezing the tab and pulling it off.
  4. Disconnect the vacuum line from the regulator.
  5. If equipped with a bolt on-type regulator, perform the following:
    1. Remove the regulator attaching bolt(s)/screw(s) from the bracket.
10_1_2011_3_13_11_am.jpg
Image LINK

Fig. 1: Remove the 2 fuel pressure regulator-to-rail attaching bolts (fuel rail removed from vehicle)

  1. If equipped with a snapring-type regulator, perform the following:
    1. Remove the snapring from the regulator.
  2. Wrap a towel around the regulator to catch any fuel that may escape. Remove the regulator from the fuel rail using a twisting and pulling motion.
10_1_2011_3_16_21_am.jpg
Image LINK

Fig. 2: ... then remove the regulator by using a twisting and pulling motion
  1. If equipped with a bolt on-type pressure regulator, disconnect the fuel return tube assembly from the pressure regulator.
  2. Cover all openings with masking tape to prevent dirt entry. If the regulator is being reused, inspect the filter screen, if equipped, for contamination. If contamination exists, replace the filter screen

10_1_2011_3_18_32_am.jpg

Image LINK

Fig. 3: Exploded view of the regulator mounting on the fuel rail - VIN K engine shown

10_1_2011_3_20_13_am.jpg

Image LINK
Fig. 4: Some regulators, such as this 1995 VIN L, are secured with a mounting bolt
  1. If further disassembly is necessary, perform the following:
    1. Remove the small regulator O-ring.
    2. Remove the regulator filter screen.
    3. Remove the large regulator O-ring.
    4. Remove the O-ring back-up.

10_1_2011_3_26_12_am.jpg

Image LINK

Fig. 5: Exploded view of the regulator housing (1), small O-ring (2), filter screen (3), large O-ring (4), O-ring back-up (5), regulator (6) and snapring (7)To install:
  1. If the regulator was disassembled, perform the following:
Lubricate all O-rings with clean engine oil prior to assembly.
    1. Install a new regulator O-ring back-up and large O-ring.
    2. Install the regulator filter screen.
    3. Install the small regulator O-ring.

  1. If the regulator is not being replaced with a new one, lubricate new O-rings with clean engine oil, then position them on the old regulator.
10_1_2011_3_28_18_am.jpg

Image LINK

Fig. 6: If the regulator is not being replaced, remove and discard the old O-rings
  1. If necessary, connect the fuel return tube to the pressure regulator and secure with the retaining nut. Tighten the nut to 13 ft. lbs. (17 Nm).
  2. Install the regulator into the regulator housing and seat with even pressure.
    1. Install the snapring or retaining bolt(s)/screw(s), as applicable.
  3. Attach the vacuum line to the regulator.
  4. If removed, connect the fuel return tube to the pressure regulator.
  5. Connect the negative battery cable.
  6. Turn the ignition switch ON and OFF to allow fuel pressure back into system. Check for leaks.
Hope helps.

Oct 01, 2011 | 1987 Chevrolet S-10 Pickup

1 Answer

How to install a fuel presure regulator on a 1998 chevrolet tahoe


Fuel Pressure Regulator - REMOVAL & INSTALLATION
(see Figure 1)
  1. Disconnect the negative battery cable.
  2. Relieve fuel system pressure.
  3. Disconnect the ignition coil.
  4. Remove the upper intake manifold.
  5. Disconnect the vacuum line to the regulator.
  6. Remove the snapring from the regulator housing.
  7. Place a towel under the regulator to absorb any spilled fuel and remove the pressure regulator from the fuel rail socket.
  8. Remove the pressure regulator from the fuel rail.
  9. Remove the pressure regulator O-ring filter, O-ring backup and O-ring and discard them.
zjlimited_1663.jpg

Fig. 1: Exploded view of the pressure regulator assembly-MFI systems



To install:

  1. Before installing the O-rings, lubricate them with clean engine oil and install them on the regulator inlet as a complete assembly.
  2. Install the snapring retainer into the slot on the regulator housing.
  3. Connect the vacuum line to the regulator.
Ensure that the retainer is properly seated in the slot in the regulator housing. Pull on the regulator to make sure that it is properly seated.
  1. Connect the negative battery cable.
  2. Turn the ignition ON for 2 seconds and then turn it OFF for 10 seconds. Again turn the ignition ON and check for leaks.
  3. Install the manifold plenum.
Hope this helps.

Aug 02, 2011 | 1998 Chevrolet Tahoe

1 Answer

I need to replace de fuel presurre sensor in a pontiac montana ,do i have to just replace the sensor ,o the sensor came with the fuel pump?thank you


Replacing the fuel pressure regulator, involves just replacing the regulator at the end of the fuel rail in the engine compartment, but fuel pressure sensor - does this mini-van have a fuel pressure sensor?
replacing the fuel pressure regulator: (1) locate it at the end of the fuel rail in the engine compartment,
(2) relieve fuel system pressure (3) disconnect fuel pressure regulator vacuum line. (4) remove fuel pressure regulator retaining screw (retain for re-use (5) using a shop towel to catch spilled fuel, lift & twist Fuel pressure regulator to remove it from the fuel rail. (6) remove/discard retainer and spacer bracket from the fuel rail. (7) remove fuel pressure regulator from the engine fuel return pipe. (8) remove/discard Fuel Pressure Regulator inlet O-ring (9) Check Fuel Pressure Regulator filter screen for contamination - if contaminated, replace Fuel Pressure Regulator. (10) Lubricate new Fuel Pressure Regulator inlet O-ring with clean engine oil & install onto the Fuel Pressure Regulator inlet. (11) Install the fuel return pipe onto the Fuel Pressure regulator (12) Install new retainer & spacer bracket into the slot on the fuel rail.
(13) Install Fuel Pressure Regulator onto Fuel Rail & tighten Engine Fuel Return Pipe nut to 13 ft-lbs (17 Nm). (14) connect Fuel Pressure Regulator vacuum line, (15) Install Fuel Pressure Regulator attachng screw & tighten to 76 in-lbs (8.5 Nm). (16) Inspect & verify that retainer & spacer bracket is engaged in the slots on the fuel rail. Grasp & pull on the Fuel Pressure Regulator.
to ensure that the Fuel Pressure Regulator is properly seated. (17) inspect for fuel leaks with this
procedure: On 2sec,(holy rollers), off 10sec will be left on, inspect for leaks while running.

Dec 11, 2010 | 2000 Pontiac Montana

1 Answer

Overreving with no power and excessive gas consumption air filter cleaned map sensor replaced fuel pump and filter


usually caused by busted diaphram in fuel pressure regulator allowing fuel to be drawn thru regulator directly to intake manifold. Pull vacuum line off regulator, plug line with golf tee, start car and watch to see if gas comes out of regulator. If yes, turn off car, replace regulator. The regulator sits near the fuel rail on the top of the engine as shown below. I will paste replacement instructions below from autozone.com in case you need to replace the regulator. Please let me know if you have any questions.
jturcotte_421.gif


Removal & Installation

4.2L Engine

  1. Relieve the fuel system pressure.
  2. Remove the air cleaner outlet resonator.
  3. Disconnect the engine wiring harness from the retaining clips at the front of the engine.
  4. Disconnect the fuel pressure regulator vacuum line.
  5. Clean any dirt from the fuel pressure regulator and the surrounding area.
  6. Disconnect the fuel return pipe.
  7. Remove the fuel return pipe retainer.
  8. Remove the fuel pressure regulator retainer.
  9. Remove the fuel pressure regulator.
  10. Inspect the regulator filter screen for contamination. If contaminated, replace the fuel pressure regulator.

To install:
  1. Install the regulator filter.
  2. Install the new O-ring on the fuel pressure regulator.
  3. Lubricate the fuel pressure regulator O-ring with clean engine oil.
  4. Push the fuel pressure regulator into the regulator housing on the fuel rail.
  5. Install the fuel pressure regulator retainer. Tighten the regulator retainer screw to 71 inch lbs. (8 Nm).
  6. Install the fuel return pipe retainer. Tighten the return pipe retainer screw to 71 inch lbs. (8 Nm).
  7. Connect the fuel return pipe.
  8. Connect the fuel pressure regulator vacuum line.
  9. Connect the negative battery cable.
  10. Inspect for leaks:
    1. Turn ON the ignition for 2 seconds.
    2. Turn OFF the ignition for 10 seconds.
    3. Turn ON the ignition.
    4. Inspect for fuel leaks.

  11. Install the engine wiring harness into the retaining clips at the front of the engine.
  12. Install the air intake resonator.

Dec 08, 2010 | 2002 Chevrolet TrailBlazer

1 Answer

If i put a little gas in the carberator and fight with my blazer it will start and stay started, but if i leave it for awhile, it will turn over but not start. i cant figure out if it is electric or...


Get a fuel pressure gauge and connect it to the rail for the fuel injectors to read pressure.

If the pressure is too low, it might be a bad fuel pressure regulator or pump:

Fuel Pressure Regulator Removal & Installation 2.2L Engine To Remove:
  1. Relieve the pressure in the fuel system.
  2. Disconnect the negative battery cable.
  3. Disconnect the vacuum hose from the fuel pressure regulator.
  4. Remove the pressure regulator mounting screw.
  5. Remove the fuel pressure regulator assembly with O-ring. Inspect filter screen for contamination. If contaminated, remove and discard.
Fuel pressure regulator removal/installation (2.2L SFI engine) gm-05-22-619.gif

To Install:
  1. Apply clean engine oil to the new pressure regulator O-ring and install the O-ring on the regulator.
  2. Install the regulator on the fuel rail. Apply thread-locker to the mounting screw.
    • Tighten the screw to 106 lb in (12Nm).
  3. Connect the negative battery cable.
  4. Use the following procedure to pressurize the fuel system and check for leaks;
  5. Turn the ignition ON for 2 seconds.
  6. Turn the ignition OFF for 10 seconds.
  7. Turn the ignition switch back ON to run the fuel pump again and pressurize the fuel system.
  8. Check the fuel rail assembly for fuel leaks.
4.3L Engine RPO L35 To Remove:
4.3L (RPO L35) Fuel meter body assembly gm_trk_sil15_02-04_43_fuel_metr_body_assy.gif

  1. Before servicing the vehicle, refer to the Cautions and Warnings in the beginning of this section
  2. Remove or disconnect the following:
    • Upper intake manifold (See: Upper Intake Manifold)
    • Fuel pressure regulator retainer clip (M) and discard the clip
    • Regulator (N) from the housing by twisting and pulling the fuel pressure regulator (N) and using a shop towel to catch any spilled fuel
    • Regulator seal O-ring (R) and discard the O-ring seal
    • Regulator filter (Q) and discard the filter
    • Regulator seal O-ring (P) and discard the O-ring seal
    • Backup ring (O) and discard the ring
  3. Cover the fuel pressure regulator housing to prevent contamination from entering the fuel system
To Install:
4.3L (RPO L35) Fuel meter body assembly gm_trk_sil15_02-04_43_fuel_metr_body_assy.gif

  1. Lubricate the NEW O-ring seals with clean engine oil
  2. Assemble the following new parts to the fuel pressure regulator:
    • Backup ring (O)
    • Regulator seal O-ring (P)
    • Regulator filter (Q)
    • Regulator seal O-ring (R)
  3. Install or connect the following:
    • Fuel pressure regulator with the vacuum tube pointing down
    • Fuel pressure regulator retainer clip (M)
    • Upper manifold
  4. Test drive the vehicle to confirm the repairs
RPO LU3 To Remove:
4.3L (RPO LU3) Fuel meter body assembly gm_trk_sil15_02-04_43_rpolu3_fuel_metr_body_assy.gif

  1. Before servicing the vehicle, refer to the Cautions and Warnings in the beginning of this section
  2. Remove or disconnect the following:
    • Upper intake manifold
    • Fuel pressure regulator retainer clip (E)
    • Regulator (F) from the housing by twisting and pulling the fuel pressure regulator (F) while using a shop towel to catch any spilled fuel
    • Regulator seal O-ring (J) and discard the O-ring seal
    • Regulator filter (I) and discard the filter
    • Regulator seal O-ring (H) and discard the seal
    • Backup ring (G) and discard the backup ring
  3. Cover the fuel pressure regulator housing to prevent contamination from entering the fuel system
To Install:
4.3L (RPO LU3) Fuel meter body assembly gm_trk_sil15_02-04_43_rpolu3_fuel_metr_body_assy.gif

  1. Lubricate the NEW O-ring seals with clean engine oil.
  2. Assemble the following new parts to the fuel pressure regulator:
    • Backup ring (G)
    • Regulator seal O-ring (H)
    • Regulator filter (I)
    • Regulator seal O-ring (J)
  3. Install or connect the following:
    • Fuel pressure regulator (F) with the vacuum tube pointing down
    • Fuel pressure regulator retainer clip (E)
    • Upper intake manifold
  4. Test drive the vehicle to confirm the repairs
prev.gif next.gif

Nov 04, 2010 | 2002 Chevrolet Blazer

1 Answer

I have a 2004 Tahoe which has misfire problems (P0300). I changed the plugs, wires, fuel filter and air filter but problem still exist. The 4 plugs on the passenger side continue to file out and become...


Removal & Installation of fuel Regulators on
4.8L, 5.3L & 6.0L Engine To Remove:
CAUTION
Three styles of fuel pressure regulators and fuel rails will be used in this model year. Each regulator has a different "footprint" that consequently changes the size of the receiving port in the fuel rail. The regulator retaining clips are specific to each rail-regulator design and cannot be interchanged.
chevy_aval15_02-04_fuelrail.gif

  1. Remove the engine sight shield.
  2. Relieve the fuel system pressure. Refer to Fuel Pressure Relief Procedure.
  3. Clean the fuel pressure regulator retainer and the surrounding area.
  4. Remove or disconnect the following:
    • Fuel pressure regulator vacuum line.
    • Fuel pressure regulator retainer.
    • Fuel pressure regulator.
  5. Remove the following parts from the fuel rail:
    • Backup ring (10)
    • Regulator Seal O-ring (11)
    • Regulator filter (12)
    • Regulator seal O-ring (13)
To Install:
chevy_aval15_02-04_retainer.gif

  1. Make sure the NEW fuel pressure regulator retainer is the right one.
  2. The tabs (1) are used on the straight vacuum port retainer (2), and the E85-straight vacuum port retainer (3).
  3. The angle vacuum port retainer (4) has no tabs. chevy_aval15_02-04_fuelrail.gif

  4. Install the following parts onto the fuel pressure regulator (9).
    • Backup ring (10)
    • Regulator seal O-ring (11)
    • Regulator filter (12)
    • Regulator seal O-ring (13)
  5. Lubricate the fuel pressure regulator O-rings with clean oil.
  6. Install the fuel pressure regulator and retainer. CAUTION
    Whenever the fuel pressure regulator is removed from the fuel rail NEW O-rings and a NEW retaining clip should be used on reinstallation.
  7. Connect the vacuum line.
  8. Tighten the fuel filler cap.
  9. Use the following to inspect for leaks:
    • Turn ON the ignition, with the engine OFF, for 2 seconds.
    • Turn OFF the ignition for 10 seconds.
    • Turn ON the ignition, with the engine OFF.
    • Install the engine sight shield.
8.1L Engine To Remove:
Fuel pressure regulator vacuum line gm_trk_sub15_fuel_press_reg_vac_line.gif

  1. Before servicing the vehicle refer to the precautions at the beginning of thjs section
  2. Remove the fuel injector sight shield as needed
  3. Relieve fuel system pressure (See: Fuel Pressure Relieving)
  4. Disconnect the fuel pressure regulator vacuum line (A) 8.1L Fuel pressure regulator retainers gm_trk_sub15_81l_fuel_press_reg_retainers.gif

  5. Clean any dirt from the fuel pressure regulator retainer and the surrounding area
  6. Remove the fuel pressure regulator retainer (I)
  7. Remove the fuel pressure regulator (H) from the fuel pressure regulator housing
To Install:
8.1L Fuel pressure regulator retainers gm_trk_sub15_81l_fuel_press_reg_retainers.gif

  1. Install or connect the following:
    • Backup ring (J) on the fuel pressure regulator (H)
    • New large O-Ring (K) on the fuel pressure regulator
    • Regulator filter (L) on the fuel pressure regulator
    • New small O-Ring (M) on the fuel pressure regulator
  2. Lubricate the fuel pressure regulator large O-Ring and the small O-Ring with clean engine oil
  3. Push the fuel pressure regulator onto the regulator housing on the fuel rail
  4. Install a new fuel pressure regulator retainer (I)
  5. Install or connect the following:
    • Fuel pressure regulator vacuum line
    • Negative battery cable
  6. Tighten the fuel filler cap
  7. Inspect for leaks using the following procedure:
    • Turn on the ignition with the engine off for two seconds
    • Turn off the ignition for 10 seconds
    • Turn on the ignition with the engine off
    • Inspect for fuel leaks
  8. Install the fuel injector sight shield
  9. Road test the vehicle to check performance
prev.gif next.gif

Sep 02, 2010 | Chevrolet Tahoe Cars & Trucks

2 Answers

Have 1998 safari 4.6 throttle body cannot find fuel pressure regulator


Astro, Safari 1997-2005

Fuel Pressure Regulator - Removal & Installation
  1. Disconnect the negative battery cable.
  2. Relieve the fuel system pressure. Refer to the fuel system relief procedure in this section.
  3. Remove the upper manifold assembly.
  4. Remove the fuel pressure regulator vacuum tube.
  5. Disassemble the fuel pressure regulator snapring retainer.
  6. Remove the fuel pressure regulator assembly and the O-rings. Discard the O-rings, filter and back-up O-rings.

    5d30462.jpg
    Fig. The fuel pressure regulator is retained by this clip


    913de3d.jpg
    Fig. Replace the O-rings whenever the fuel pressure regulator is removed
To install:
  1. Lubricate the O-rings with clean engine oil and install as an assembly.
  2. Install the fuel pressure regulator, attach the vacuum tube.
  3. Install the snapring retainer.
  4. Install the upper manifold assembly.
  5. Connect the negative battery cable.

  1. Relieve the fuel system pressure.
  2. Remove the upper intake manifold assembly.
  3. Remove the fuel pressure regulator retainer clip (5).
  4. Pull and twist the fuel pressure regulator (6) in order to remove the fuel pressure regulator from the fuel pressure regulator housing using a shop towel to catch any spilled fuel.
  5. Remove the regulator seal lower O-ring (3).
  6. Remove the regulator assembly filter (2).
  7. Remove the regulator seal upper O-ring (1).
  8. Remove the regulator seal backup ring (7).
  9. Discard the O-rings.

    a29bed6.jpg
    Fig. Exploded view of throttle body assembly (click for zoom)
To install:

NOTE If the fuel pressure regulator is to be reinstalled, inspect the filter screen for contamination. If the filter screen is contaminated, replace the regulator.
  1. Lubricate the new O-rings with clean engine oil.
  2. Install the regulator seal backup ring (7).
  3. Install the regulator seal upper O-ring (1).
  4. Install the regulator assembly filter (2).
  5. Install the regulator seal lower O-ring (3).
  6. Assemble the regulator (6) with the vacuum tube pointing down into the regulator retainer clip.
  7. Install the fuel pressure regulator retainer clip (5).
  8. Install the upper manifold assembly.
  9. Connect the negative battery cable.
  10. Inspect for leaks.
    1. Turn the ignition ON , with the engine OFF , for 2 seconds.
    2. Turn the ignition OFF for 10 seconds.
    3. Turn the ignition ON , with the engine OFF .
    4. Inspect for fuel leaks.
  11. Install the engine cover.

Hope helps with this (remember comment and rated this).

Aug 05, 2010 | GMC Safari Cars & Trucks

2 Answers

Locating fuel pressure regulator


Fuel Pressure Regulator Removal & Installation 2.2L Engine To Remove:
  1. Relieve the pressure in the fuel system.
  2. Disconnect the negative battery cable.
  3. Disconnect the vacuum hose from the fuel pressure regulator.
  4. Remove the pressure regulator mounting screw.
  5. Remove the fuel pressure regulator assembly with O-ring. Inspect filter screen for contamination. If contaminated, remove and discard.
Fuel pressure regulator removal/installation (2.2L SFI engine) gm-05-22-619.gif

To Install:
  1. Apply clean engine oil to the new pressure regulator O-ring and install the O-ring on the regulator.
  2. Install the regulator on the fuel rail. Apply thread-locker to the mounting screw.
    • Tighten the screw to 106 lb in (12Nm).
  3. Connect the negative battery cable.
  4. Use the following procedure to pressurize the fuel system and check for leaks;
  5. Turn the ignition ON for 2 seconds.
  6. Turn the ignition OFF for 10 seconds.
  7. Turn the ignition switch back ON to run the fuel pump again and pressurize the fuel system.
  8. Check the fuel rail assembly for fuel leaks.
4.3L Engine RPO L35 To Remove:
4.3L (RPO L35) Fuel meter body assembly gm_trk_sil15_02-04_43_fuel_metr_body_assy.gif

  1. Before servicing the vehicle, refer to the Cautions and Warnings in the beginning of this section
  2. Remove or disconnect the following:
    • Upper intake manifold (See: Upper Intake Manifold)
    • Fuel pressure regulator retainer clip (M) and discard the clip
    • Regulator (N) from the housing by twisting and pulling the fuel pressure regulator (N) and using a shop towel to catch any spilled fuel
    • Regulator seal O-ring (R) and discard the O-ring seal
    • Regulator filter (Q) and discard the filter
    • Regulator seal O-ring (P) and discard the O-ring seal
    • Backup ring (O) and discard the ring
  3. Cover the fuel pressure regulator housing to prevent contamination from entering the fuel system
To Install:
4.3L (RPO L35) Fuel meter body assembly gm_trk_sil15_02-04_43_fuel_metr_body_assy.gif

  1. Lubricate the NEW O-ring seals with clean engine oil
  2. Assemble the following new parts to the fuel pressure regulator:
    • Backup ring (O)
    • Regulator seal O-ring (P)
    • Regulator filter (Q)
    • Regulator seal O-ring (R)
  3. Install or connect the following:
    • Fuel pressure regulator with the vacuum tube pointing down
    • Fuel pressure regulator retainer clip (M)
    • Upper manifold
  4. Test drive the vehicle to confirm the repairs
RPO LU3 To Remove:
4.3L (RPO LU3) Fuel meter body assembly gm_trk_sil15_02-04_43_rpolu3_fuel_metr_body_assy.gif

  1. Before servicing the vehicle, refer to the Cautions and Warnings in the beginning of this section
  2. Remove or disconnect the following:
    • Upper intake manifold
    • Fuel pressure regulator retainer clip (E)
    • Regulator (F) from the housing by twisting and pulling the fuel pressure regulator (F) while using a shop towel to catch any spilled fuel
    • Regulator seal O-ring (J) and discard the O-ring seal
    • Regulator filter (I) and discard the filter
    • Regulator seal O-ring (H) and discard the seal
    • Backup ring (G) and discard the backup ring
  3. Cover the fuel pressure regulator housing to prevent contamination from entering the fuel system
To Install:
4.3L (RPO LU3) Fuel meter body assembly gm_trk_sil15_02-04_43_rpolu3_fuel_metr_body_assy.gif

  1. Lubricate the NEW O-ring seals with clean engine oil.
  2. Assemble the following new parts to the fuel pressure regulator:
    • Backup ring (G)
    • Regulator seal O-ring (H)
    • Regulator filter (I)
    • Regulator seal O-ring (J)
  3. Install or connect the following:
    • Fuel pressure regulator (F) with the vacuum tube pointing down
    • Fuel pressure regulator retainer clip (E)
    • Upper intake manifold
  4. Test drive the vehicle to confirm the repairs
prev.gif next.gif

Aug 05, 2010 | 2001 Chevrolet Blazer

1 Answer

Air compressor pressure not regulating


Usually you cannot adjust the cut out pressure of the tank/motor itself, this is why they have regulators, which regulates the pressure flowing down the air lines (regulators like these dont regulate actual tank pressure cutout). To regulate air flow using the regulator knob, you actually have to have air flowing through the hose while you make the regulator/pressure adjustments as regulators regulate pressure DOWNSTREAM from the actual regulator itself.. so air flowing through is a must. Attach an air blower or something similar and let air start flowing through the hose. Now turn your regulator knob in the "-" direction to decrease regulated pressure. It is best to bring pressure all the way down to "0" first, then open the regulator up (by turning to the "+" side) and pressure will rise until you get to the desired pressure needed for the air tool in use. The tank pressure will still be between 80-125 PSI as the motor regulates and keeps the pressure in the tank between these values automatically, but your line/hose air flow pressure will remain at the regulated pressure (say 40 PSI or whatever you set using the regulator knob).

Hope that helps and makes sense.

Please rate this solution on FixYa!

Jun 18, 2009 | Makita Factory-Reconditioned 2.5 HP Air...

1 Answer

Regulator problems


Sounds like your regulator is faulty, I would start there. Be sure any regulator you have installed is installed correctly, not backwards as reversed regulators will not work properly. Also be sure to keep regulators clean, there are breather holes in regulators to break vacuum when the regulator opens and closes, if these are clogged the regulator will not open or close properly. Hope this is helpful.

Apr 29, 2009 | Kitchen Appliances - Others

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

533 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sym Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

75066 Answers

montehammons

Level 3 Expert

5252 Answers

Are you a Sym Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...