Question about 2008 KTM 300 EXC-E

Open Question

How to remove rad hoses that go through the frame at top of rad on KTM 300exc 2008 enduro, there is a tee piece which joins the rad together at the top with one pipe going down inside frame,how to remove this pipe, thanks

Posted by Anonymous on

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 3567 Answers

SOURCE: antifreeze is filling gear box on a 1999 ktm

The water is getting past the water pump seals and into the gearbox. New seals are needed.

Posted on Oct 25, 2009

Ad
sultansikand
  • 275 Answers

SOURCE: i need a wiring diagram

only findout from company.

Posted on Jun 29, 2011

TerryTown
  • 292 Answers

SOURCE: Where do I find torque

Thank you for contacting FixYa with your inquiry.
You will find some excellent technical specifications on the bottom of the review at the following link:
http://knowledgeareas.com/2010-ktm-300-exc-review-and-specifications
Modification Site to increase Engine Torque: http://slavensracing.com/services/ktm-2-stroke-services/ktm-2-stroke-engine-services
Please advise if we can be of further assistance.
Kind regards,
TF

Posted on Jul 17, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you change the radiator


start by draining the rad.remove hoses top and bottom if automatic remove the transmission lines then undo bolts that hold rad. in frame then reinstall new one in reverse good luck also put antifreeze and water mix half and half.there you go

Apr 09, 2016 | 2008 Chevrolet Uplander

1 Answer

My 1991 300exc.keeps overheating after quick ride whats up,recently atifreeze was drained


Make sure its bled through correctly, make sure you can run a flow of water through with bottom rad hose off, check thermostat water pump and fan switch

Jan 28, 2012 | KTM Motorcycles

1 Answer

Where do I find torque specs for a 2010 ktm 300exc


Thank you for contacting FixYa with your inquiry.
You will find some excellent technical specifications on the bottom of the review at the following link:
http://knowledgeareas.com/2010-ktm-300-exc-review-and-specifications
Modification Site to increase Engine Torque: http://slavensracing.com/services/ktm-2-stroke-services/ktm-2-stroke-engine-services
Please advise if we can be of further assistance.
Kind regards,
TF

Jul 03, 2011 | 2010 KTM 300 EXC

1 Answer

I need to know which wires must be cut and joined to dissable the sidestand switch.....there are 3 wires black / blue / pink


This is dangerous, I recommend replacing the switch. If you insist, test which are hot and which are ground. Once you know this take a wire and plug it into 2 wires if bike dies you got it right. Otherwise use the other pair. I recommend fusing your wire to avoid damaging anything.

Feb 19, 2010 | 2008 KTM 950 Super Enduro R

1 Answer

Ktm 950 enduro runs fine for 30 km then dies as if no fuel.give it five minutes and will run fine. bike has now 20000km


possible issue on timing and or internal overheating.

KTMs vtwin timing is a little hard to decipher so i rather you have your bike brought to a KTM service center for overhauling.

please do not use the bike before it gets repaired. this king of issue may damage your cylinder

Jan 06, 2010 | 2008 KTM 950 Super Enduro R

1 Answer

Where is thermostat in a 1995 chrysler cirrus LX


A tee is located to the right hand side of the intake manifold, on top you should see the coolant system cap, its silver in color and is about 2-3 inches in diameter. This tee is the thermostat housing, it goes to your radiator and engine block, remove it from the block and you should see the thermostat. Remember when replacing the thermostat, the spring side goes into the block! 2.0L and 2.4L it is under where the upper rad hose hooks to the engine. 2.5L it is under where the lower rad hose hooks to the engine.

Dec 29, 2009 | 1996 Chrysler Cirrus

1 Answer

Antifreeze is filling gear box on a 1999 ktm 300exc.what is the problem


The water is getting past the water pump seals and into the gearbox. New seals are needed.

Oct 25, 2009 | 2008 KTM 300 EXC-E

1 Answer

Replacing a/c condenser on 2008 Pontiac G6


NOT SIMPLE,COND & RADIATOR ARE INSTALLED TOGETHER.DRAIN COOLANT(TAP IS ON BOTTOM LH SIDE).IT WILL BE EASIER TO DO IF YOU REMOVE THE FILLER PLASTIC BETWEEN BUMPER &RAD SUPPORT.REMOVE RAD HOSES,UNPLUG COOLING FANS (2) CONNECTORS.A/C HOSES ARE ALSO ON LH SIDE OF COND.IT IS ADVISED TO HAVE THE REFRIDGERENT EVACUATED BEFORE YOU UNHOOK THEM.WHEN YOU HAVE THE RAD OUT TAKE OFF THE FANS,THEN SLIP THE A/C CONDESER OFF THE RADIATOR.

Jun 26, 2009 | 2008 Pontiac G6

1 Answer

Leaking fork seals


Im replacing the fork seals on my 250yzf just wondering what the oil is thanx gary














Mar 15, 2009 | 2008 KTM 300 EXC-E

Not finding what you are looking for?
2008 KTM 300 EXC-E Logo

Related Topics:

96 people viewed this question

Ask a Question

Usually answered in minutes!

Top KTM Experts

yadayada
yadayada

Level 3 Expert

77544 Answers

bazzz7071
bazzz7071

Level 2 Expert

342 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers

Are you a KTM Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...