Question about 1996 Yamaha YZF 600 R thunder cat

1 Answer

I have a noize in the clutch **** wene i pull the cluch in it goes

Posted by Anonymous on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 8,909 Answers

A job to advise without seeing it but I think there is a problem with the actuator mechanism as opposed to the clutch itself.
Check the thrust bearing for wear.

Posted on Dec 30, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 5 speed wen i come off the cluch and get up to high rpm it fill like my trans is sliping


The clutch is probably worn out and slipping and needs to be replaced. With a manual transmission, if the engine revs and the car doesn't accelerate at the same pace, the clutch is slipping. This usually gets very very worse almost instantly. The clunking could be related or it could be an unrelated problem you're just noticing now that you have a slipping clutch. Has the car recently made clicking noises while turning sharp corners or in reverse? If yes, maybe a bad CV joint. If you don't have the technical aptitude to remove the transmission and replace the clutch, I suggest taking it to a shop to have them check into it. Clutches are a wear item and go bad around 90,000 miles of use.

Mar 10, 2014 | 1988 Chevrolet Cavalier Z24

2 Answers

Let out the clutch it barely goes, clutch slipping maybe?


Sounds like your clutch has seen it last mile, it's worn replace it and you'll be fine.

Jul 02, 2010 | 1995 Isuzu Pickup

1 Answer

Mercedes sprinter 216 manual gearbox sound when not presing cluch pedal, goes away when you press the cluch pedal.


it seems that the clutch is not aligned or not setup right to it's correct default mode. when you lift the foot off the clutch it goes into default and away from the gears. this could be an early sign off needing a new clutch and pressure plate. good luck.

May 07, 2010 | 1999 Mercedes-Benz E-Class

1 Answer

When driving cluch goes in when driving the reves


Sounds like you need a new clutch. At a stand still put the car in third and try to get it to move. If you don't stall out you need a new clutch.

Apr 07, 2010 | 2000 Ford Focus

1 Answer

My cluch keeps stiking to the floor in my 1989 mazda mx6


check all mechanical parts of clutch pedal make sure there is no catching or draging in its joint lube if possible also check the spring that pulls the clutch pedal back up make sure not damaged or worn out, A different problem may be in your hydrolic clutch system, such as a bad slave cylinder or your system may just need bleeding, if you have a problem with your hydrolics when the clutch goes to the floor and stays you will not be able to disengage your clutch as well until you pull the clucth back up and pump it a few times.

Apr 03, 2010 | 1989 Mazda MX-6

1 Answer

I have a 2001 kawasaki zr7s. My clutch is acting up. when i pull the lever in i have no clutch. i opened the case to get to the clutch, that rod thats in the middle of the clutch acts like there should be...


the "cluch push rod" should be pushed back by the cluch springs, if there was a bearing on the end it would have broken up and be laying inside the cluch case in bits! if you have taken the cluch to bits there is a thrust washer behind the cluch body and gear box shaft if you left this washer out you wont have a cluch? best bet is get a hayns service book for your bike maybe off e-bay and you will have all the info you need to fix it plus all the photos as well of all the parts

Jan 14, 2010 | 2001 kawasaki ZR-7 S

1 Answer

Washing machin cluch


Remove front panel, remove spring clip holding clutch to motor shaft then pull clutch off shaft or gently pry off if stuck.

Sep 09, 2009 | Washing Machines

1 Answer

Need to replace fan cluch


the radiator fan is mounted to the clutch, in other words remove the bolts / nuts that is holding the fan assembly to the water pump usually just four nuts once you pull the fan assembly the part that yo seperated from the water pump is the clutch, now remove the fan blades and mount thm on the new clutch assembly the piece which mounts tt the water ump is the fan clutch

Jul 10, 2009 | 2000 Kia Sportage

1 Answer

HELP the cluch on my 1993 VW golf is haveing problmes


From what I am gathering. the pedal and cable assemblys are ok. then it is time to tear into the clutch its self. Sounds like the throwout bearing is bad.

Jan 29, 2009 | 1999 Volkswagen Golf

2 Answers

Clutch pedal


hi there have you turned the clutch arm upside down and pushed the cluch release brging into the cover cliping it in to the cover as these have a pull type clutch.

Jan 07, 2009 | 2009 Hyundai Genesis

Not finding what you are looking for?
1996 Yamaha YZF 600 R thunder cat Logo

Related Topics:

91 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Experts

dhnguyen

Level 2 Expert

281 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1144 Answers

Tony

Level 3 Expert

2600 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...