Question about 2001 Honda CB 600 Hornet F

Open Question

2001 hornet, what oil is used in forks, what depth from the top of the fork do i leave

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

fastboyz
  • 674 Answers

SOURCE: KX 125 (2003) motorcycle

its 120 mm or 4.7 inches from the top of the fork
Some measure the oil quantity and fill the fork up, some fill the fork up and measure the oil level. The most correct method is to measure the level, I guess, but many guys measure in quantity.. both ways work well.
1dcced6.jpg

Posted on Nov 28, 2008

robotek
  • 1512 Answers

SOURCE: front fork oil capacity

Hi
You can download the whole workshop service manual that has this info and heaps more from here. Hope this helps Thanks for using Fixya. 
regards robotek

Posted on Jan 10, 2009

  • 74 Answers

SOURCE: Fork oil level: 2006 KDX 200

This all depends on what size forks you have, but a good rule of thumb is 120ml. After that then what you want to do is to ride the bike and make adjustments to your front end until your liking.

Posted on Jan 16, 2009

  • 53 Answers

SOURCE: front fork leaking oil from bottom of the seal.

change the oil seals and oil in the fork,and avoid wheelies on the bike and off road biking 

Posted on May 17, 2009

hawk127311
  • 350 Answers

SOURCE: how much 5w oil goes into each fork?

Using 5w oil with stock springs, your oil level should be about 100mm from the top with the fork fully compressed, damper rod pushed all the way down, and the spring out. I hope this helps and good luck. Please vote and leave a message.

Posted on Oct 30, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How much fork oil in a 2002 honda hornet


Hi, Anonymous for this scenario you will need your service, parts fiche, and owners manual if you can't find the best tool you ever bought for your Honda, despair not, for a mere zero $0 you can download another one. For more information about your issue and valuable "FREE" downloads that you will need for viewing and printing please click on the blue links below. Good luck and have a wonderful day.
Fork oil level Honda 599 Forum
hondahornet co uk
Honda 1998 CB600Fw Shop Manual
http://www.partsfish.com/page/oem-parts-for-honda
Honda CB600F Owner Manual

Jul 02, 2014 | 2002 Honda CB 600 Hornet F

1 Answer

Capacity Fork Oil in Honda 06 Hornet


600cc 05/06
Front Fork Oil cc (right leg):467Front Fork Oil cc (left leg):467

Oct 21, 2013 | Motorcycles

1 Answer

Front forks what goes in them highdrolic fluid or brake fluid


Not brake fluid or Hydraulic oil ( oil weight is the issue)
Drain forks ( bottom nipple) , remove top bold , be careful it is pressurized by spring . Use the right tool otherwise will damage bolt and your face.

Front forks should be sealed properly, fork seal should be intact, no water or brake fluid in them. Right amount of fork fluid is imperative along with oil weight specification ( check manual and appropriate oil weight for your bike), wrong oil and amount can otherwise damage your forks.

Sep 19, 2012 | 2001 Yamaha YZF-R1

1 Answer

How much fork oil goes in the forks of an 2001 FXD and how do I do this ? Do you have any diagrams to help me with ?




I have no diagrams for you. MAke your own as you take it apart etc and take lots of cell phone pictures if you need help remembering how to put things back together.

Table 1-6. Type E Fork Oil Amounts



MODEL OZ CC IN. MM



FXDXT 11.5 341 6.10 154.9



FXDWG 12.0 356 7.28 184.9



FXDL 10.7 316 7.20 182.9



FXD 10.6 314 6.69 169.9




Changing fork oil is a simple mater for some models and requires fork disassembly for others. Here is the procedure for all 2001 DYNA models:

2001 DYNA FRONT FORK OIL 1.18


REPLACING FORK OIL Replace front fork oil at every 20,000 mile (32,000 km) service interval and/or prior to storage.


ALL BUT FXDX & FXDXT models


Raise and support the motorcycle so the front end is off the floor and the forks are fully extended, on FXDL models, remove the center plug from each fork cap, on all other models, remove the fork tube caps, remove the drain screws from the bottom of each fork and drain the fork oil, replace the drain screws and washers and tighten the screws

to 13-17 in-lbs (1.5-2.0 Nm) THEN see Table 1-6. and fill the fork with Harley-Davidson TYPE E FORK OIL (Part No. HD-99884-80) as set out in the Table. THEN if apart assemble the forks as follows:


a. FXD, FXDXT, FXDWG models: install both fork tube caps and tighten them to 11-22 ft-lbs (14.9-29.8 Nm).

b. FXDL models: install center plugs and tighten until secure.


Fork oil amounts can be measured two ways: use the oz./cc measurement if fork is left in frame; use the in./mm measurement if the fork is disassembled in which case the oil level is measured from the top of the fork tube with the spring removed and the fork fully compressed.


Table 1-6. Type E Fork Oil Amounts for 2001 DYNA


MODEL OZ CC IN. MM

FXDXT 11.5 341 6.10 154.9

FXDWG 12.0 356 7.28 182.9

FXD 10.6 314 6.69 169.9


PART NO. SPECIALTY TOOL

HD-41177 Fork tube holder

HD-41549A Fork spring compression tool

HD-41551 Spring plate tool

HD-36583 Fork seal installer

HD-59000A Pro-level oil gauge



FRONT FORKS: FXDX & FXDXT 2.20

REMOVAL

Raise and support the motorcycle so the front end is off the floor and the forks are fully extended, remove both front brake calipers and the front wheel, remove the front fender, remove the front fairing, remove the headlamp bracket and attach the headlamp to the frame using a rubber bungee strap, loosen the upper and lower triple clamp pinch bolts and pull the fork sides from the brackets.


DISASSEMBLY

Remove the stopper ring, remove the spring preload adjuster but DO NOT unthread the rebound adjuster from the damper rod because incorrect assembly could result in reduced adjustment range. THEN unthread the fork cap from the fork tube and allow the fork leg to drop, exposing the spring, THEN get a FORK SPRING COMPRESSION TOOL (Part No. HD-41549A) on the spring collar, turn the screws in to engage the holes in collar, compress the spring until the SPRING PLATE TOOL (Part No. HD-

41551) can be positioned between the spacer and the spring collar, THEN hold the fork bolt and compression adjuster, remove the fork bolt from the compression adjuster, remove the spring adjuster plate from the fork bolt, remove spacer, spring collar and spring, pour out the fork oil by pumping the fork leg and rod 8-10 times or until rod the moves freely. THEN position fork slider in vise using a FORK TUBE HOLDER such as (Part No. HD-41177) to avoid damage. THEN remove the socket head bolt, remove the damper from the fork tube, remove the cover from the slider, remove seal and stopper ring, pull the fork tube out of the slider, remove the oil seal, spacer and guide bushing from the fork tube.


CLEANING AND INSPECTION

Measure the fork spring free length and replace the spring if it is shorter than 17.00 in. (431.8 mm), check the fork tube and the slider for score marks, scratches or abnormal wear, check the slide and guide bushings for excessive wear or scratches, set the fork tube on V-blocks and measure runout which should not exceed 0.008 in. (0.2 mm).


ASSEMBLY

Coat the oil seal with TYPE E FORK OIL, before installing the slide bushing and guide bushing, lubricate them with fork oil, THEN install the guide bushing and the spacer seal noting that the guide bushing opening must be oriented to the side and NOT to the front or rear, THEN slip the slider into the fork tube, place the slide bushing over the fork tube until it rests on the slider, drive the guide bushing with the spacer seal into the slider, lubricate a new oil seal with TYPE E FORK Oil, drive the oil seal into the slider using FORK SEAL INSTALLER (Part No. HD-36583). install the stopper ring and dust seal, (if the rebound adjuster was removed from the damper rod bottom the lock nut on the threaded portion of damper rod, holding a thumb on the detent spring and ball, back out (turn counterclockwise) the rebound adjuster to the last "click." and then turn down (clockwise) 17 "clicks", thread the rebound adjuster onto the damper rod until the adjuster stops at maximum thread engagement (but do not force it), thread the locknut onto the damper rod up until it contacts the base of the rebound adjuster and tighten it in place), THEN holding the slider in a vise while being careful not to damage it. install the damper tube into the fork tube and tighten the socket screw and washer to 22-29 ft-lbs (29.8-39.3 Nm). THEN pour half the TYPE E FORK OIL into the fork tube, slowly pump the damper rod 10 or more times, position the damper rod in the fully bottomed position and pour the remaining amount of TYPE E FORK OIL into the fork tube. THEN using a PRO-LEVEL OIL GAUGE (Part No. HD-59000A) or similar adjust the oil level to 5.04 in. (128 mm). THEN carefully clean and install the spring, the spring collar, and the spacers with the sharp edge created when they were stamped out when manufactured, facing the collar. THEN using a FORK SPRING COMPRESSION TOOL such as (Part No. HD-41549A) push spring collar down and place a SPRING PLATE such as (Part No. HD-41551) between the spacer and the spring collar, install the fork cap and tighten it against the rebound adjuster to 22-29 ft-lbs (29.8-39.3 Nm). THEN tighten the fork cap onto the fork tube to 11-22 ft-lbs (14.9-29.8 Nm), install the spring adjuster plate, replace the O-rings on the spring preload adjuster and lubricate them with fork oil. THEN install the spring preload adjuster and the stopper ring and carefully drive the slider cover into the slider.


INSTALLATION

Insert both fork side assemblies up through the fork stem and bracket and upper bracket and tighten the fork stem bracket pinch bolt(s) to 30-35 ft-lbs (40.7-47.5 Nm). Then re-install the headlamp bracket, install the front fender, install the front wheel and the brake caliper When the motorcycle is again ready for the road adjust the headlamp and road test the motorcycle.






Feb 10, 2011 | Harley Davidson FXD Dyna Super Glide...

1 Answer

Fork seal replacement


If all you want to do it replace your fork seals, if you can find a way to jack the bike high enough, you don't have the fork tubes our ot the triple trees. Work with on fork tube at a time. Raise the bike up off the ground and take the front wheel and fender off. Brake caliper off it's tube. Now raise the bike up to where you've got about a foot of clearance below the lowest point of the slider. Look underneath the slider where the axle goes through and you'll see an 8mm bolt. Take this bolt out and your lower slider will come off. The fork oil will start to drain as soon as you take the bolt loose as well. Leave a pan under the upper fork while you work on the lower to catch the dripping oil. Replace the fork seal and reassemble that tube. Then, do the next one. Now, refill the tube with the correct amount of the correct oil from the top by removing the top cap nut. Pour in the correct amount of oil for a "wet" refill. The thicker the viscosity of the oil, the firmer the front fork action. I think they came with H-D type E which seems to be a bit softer action than 30 weight fork oil. Make sure you use fork oil. Regular engine oil or transmission oil should not be used and it will foam if you're riding down a rough road and your forks will collapse and not work until the oil settles again. Not a pleasant feeling. It's really doubtful if you'll get anywhere that is that rough with your Harley.

Good Luck
Steve

Sep 12, 2010 | 1993 Harley Davidson FXR Super Glide

1 Answer

How much 5w oil goes into each fork?


Using 5w oil with stock springs, your oil level should be about 100mm from the top with the fork fully compressed, damper rod pushed all the way down, and the spring out. I hope this helps and good luck. Please vote and leave a message.

Oct 30, 2009 | 2003 Honda CR 125 R

2 Answers

How do you cahange front fork oil in a 2001 fxdx


raise front wheel .find socket head drain plugs @ bottom of lower legs.remove top nuts to add oil.CAUTION--top nuts are under pressure of fork springs. in the old days we would add a 1'' spacer to springs for a firmer ride.

Sep 23, 2009 | 2001 Harley Davidson FXDX Dyna Super Glide...

1 Answer

Front fork oil seal replacement


General intructions for most bikes:

Remove front wheel. Loosen fork tube clamps at top and bottom of triple clamps. Slide fork tubes out and remove. Access to seals is from top of tube. Remove cover and unscrew cap. Shop manual for specific bike is $24-$30. Will show detailed instructions.

Good luck;
Techjoel

May 14, 2009 | 2001 kawasaki KDX 125

1 Answer

Is decarbonising is necessary


Hi! With modern fuels and oils there really shouldn't be any need to de-carbonise.(Unlees Mixture is incorrect?) If you are really concerned then try a quality fuel additive, read fully the directions for use and Bingo job's a good-un.
Fork oil change, is there a reason? are the forks weak? any seapage? if not leave well alone as you may open a Hornets Nest.
Telescopic forks/dampers use very light oil for suspension, too much will blow oil seals, so if you are determined to change the fluid then make sure the correct viscosity is used and critically the correct amount/quantity. Cleanliness is of the utmost!
Good Luck!
Paul 'W'
Onyer~EDson(:0)~[><

Dec 09, 2008 | 2005 Honda Unicorn

2 Answers

How to fill the front suspension on a ktm exc 2001


If you get the sevice manual or contact a dealer to get the correct oil amount for your bike, they need to know the model and year, you have to have the forks off the bike. take the fork caps off, take the springs out compress the upper fork tube all the way and add the specified oil. if they also give you the measured amount from the top that's the best way to get both fork oil levels exact. there is a special tool that you set the oil level in millimeters and it sucks out the oil to the right level, but before you do that step after adding the oil always pull and push on the cartage rod several times to remove air from the cartage tube. you will hear the air coming out and you will feel the changes in the cartage rod as the cartage tube fills up with oil and the air is removed.
something i'm confussed on though is if you replaced a seal you would have had to brake down the fork to replace it. you would have poored the oil into a container, cleaned all the internal parts,and used a fork seal driver to install the new seal. part of your question asks where do i put the oil in? thats in the open end of the fork after you have taken off the fork cap. It sounds to me like you only replaced the dust seal on one fork. that is not going to fix your leaking fork. you need to replace the oil seal thats pressed inside of the top fork tube.

Dec 01, 2008 | 2008 KTM 200 EXC

Not finding what you are looking for?
2001 Honda CB 600 Hornet F Logo

Related Topics:

156 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

75051 Answers

Gino Cussen
Gino Cussen

Level 2 Expert

216 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...