Question about 1982 Honda CX 500 B

1 Answer

What is part no for cx500 custom 1981 synthetic bung washer for spark plug drain hole

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,978 Answers

The rubber oil gasket that keeps oil from pouring past the valve cover onto the spark plug is part number 12329-415-000.

Posted on Dec 29, 2010

  • dazpitch Dec 29, 2010

    thanks mate very helpfull many thanks daz

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the bung to drain out diesel been put in my car


no bung of plug or nothing else told U 3 times now

May 01, 2015 | 2006 Nissan Maxima

1 Answer

1979 Honda CX 500 A misfires badly


Hi, Anonymous and the usual suspects are:
1. Severely discharged or a damaged battery should have 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a cursory reading of 12.5 volts or more but little or zero amperage the battery is faulty and must be replaced, AGM batteries fail in this scenario more so than lead acid batteries.
2. Check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
3. Spark plugs in bad condition or partially fouled.
4. Spark plug cables in bad condition and leaking check for spark leakage in the dark
5. Spark plug gap too close or too wide.
6. Faulty ignition coil, module, and or sensor.
7. Loose, dirty, or corroded ignition module connector at crankcase.
8. Faulty CKP or CMP, MAP, ETS, ATS, TPS, O2 sensor.
9. Dirty air filter.
10. Intake air leak.
11. Water, dirt, or rust in the fuel system.
12. Carburetor contaminated, sticky float, plugged jets.
13. Carburetor vacuum diaphragm torn, cracked, not seated or installed improperly.
14. Multiple carburetors out of sync.
15. Fuel filter clogged.
16. Old or contaminated fuel.
17. Fuel tank vent system plugged or carb vent line closed off.
18. Gas cap diaphragm valve faulty.
19. Vacuum line from intake manifold to fuel valve is broken, cracked, pinched, or missing.
20. Carburetor controls misadjusted.
21. Incorrect valve timing.
22. Valve springs floating, weak, or broken.
23. Damaged intake or exhaust valve.
24. Incompatible performance parts.
25. Control module may be in "LIMP" mode
26. Check for engine trouble codes.
For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
Honda CX500 Ignition Problems Tech Corner Motorcycle Classics
http://robdavistelford.co.uk/webspace/cx500/wontgo
Honda CX500 Shop Manual
http://www.partsfish.com/page/oem-parts-for-honda
Honda CX500 CUSTOM Owner Manual

May 24, 2014 | 1979 Honda CX 500 A

1 Answer

What is a bung


from what i understand a bung is a type of plug used to seal of the drain hole in a barrel or bucket. often you here of bung plugs being used in whiskey barrels.

Dec 30, 2011 | Dimplex CS1205 Electric Compact Heater

1 Answer

You told me about part no 12329-415-000 spark plug drain washer can you tell me how to replace step by step and would i need new rocker cover gasket or can i use old one and when finished how tight do you...


hi, the rocker cover gasket can be reused if is not damaged in any way you may want to apply a small amount of sealent to it, when tightening the rocker coverbolts when you feel them stop use only a slight amount of pressure to tighten, as they tend to break when overtightened, i am not sure what part you refere to exactly but if you mean the ruber ring that fits in the rocker cover then this is a simple job, do you have oil leaking from the weep hole in the side of the cylinder head?this ring fitted to the rocker cover stops this,

Dec 30, 2010 | 1981 Honda CX 500 B

1 Answer

Just got cx500 custom 1981 leaking oil when i start up from small hole on side of cylinder what do i do


If the oil leak is coming out of the spark plug drain hole , the inner valve cover seal is leaking or not installed correctly. Take out the two bolts holding on the valve cover and remove the cover. If the valve cover gasket has silicone on it , pick off all the silicone and put the gasket and cover back on. That should fix the problem. Silicone on the type of gasket can make it leak. If the gasket is hard or cracked replace the soft rubber gasket and put it on by itself with no extra sealant.

Dec 24, 2010 | 1982 Honda CX 500 B

1 Answer

How do i remove the seat on a 1981 Honda cx500?


The deluxe model has two latches one on either side of the seat, if you flip both levers at the same time and lift, the seat will come off. The custom model has two bolts that hold the seat down, near the back, one on each side. Remove the side covers, take off the seat bolts and lift the back of the seat pulling toward the rear of the bike.

Sep 06, 2010 | 1981 Honda CX 500 B

1 Answer

1981 CX 500 B: 1981 Honda CX500 idles at about 2500 rpm. How to ...


under the carbs there is a little black screw turn this by hand anti clockwise until 1-1500 revs if this doesnt work the choke may not be going all the way off or pilot screws under float bowls in recess been adjusted too far screw gently all the way in DO NOT over tighten then unscrew approx 1.5 turns out on both carbs if your experiencing flooding from carbs the bowls need to be removed and the pilot jet attached to the float needs replacing hope this helps steve

May 17, 2010 | 1981 Honda CX 500 B

1 Answer

WHERE IS THE FILLER PLUG ON THE GEARBOX ON A 1998 PASSAT TDI PLEASE


Hi,

Just checking.... it is a manual gearbox?

You may need a special tool for the drain plug and a 17mm allen key for the filler (some use the special drain tool for the filler as well)

The drain plug is located under the diff housing.

The filler plug is located on the left (nearside) off the gearbox (look to the left of the hole and you can see the 17mm hex filler bung).

Check you can undo the filler bung, then drain the gearbox oil.

Refit drain bung and fill gearbox through filler/level ********* until gearbox oil is up to the level of the filler bung.

Refit, test drive, check for leaks and retest level again when cold.

Cheers,

"If this has helped you in any way, please rate this solution" :-)

Jan 27, 2010 | 1998 Volkswagen Passat

1 Answer

Need to lower


try a cut down seat instead.

Sep 01, 2009 | 1981 Honda CX 500 B

Not finding what you are looking for?
1982 Honda CX 500 B Logo

Related Topics:

206 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

75822 Answers

Mike

Level 3 Expert

4336 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...