Question about Transport Schwinn Rechargeable Portable Scooter

1 Answer

SchwinnS350 While trying to replace batteries in the battery pack, uhooked the tandem wiring and am unsure how to re-install. Help!!!!

Posted by on

  • Tone-Tone Jun 28, 2008

    Not certain how to reconnect wires for the two tandem replacemnt batteries.

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 3 Answers

Probably Red to scooter to one battery's positive. That batterys negative to other battery's positive and that battery's negative to scooters black wire. Everything will connect in a series.

Posted on Jul 28, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I wire two tandem batteries for an electric scooter


Tandem batteries... is a fairly loose term to be dealing with on batteries... SIMPLY BECAUSE THEY ARE EXPLOSIVE.


TANDEM voltage
(assuming you were trying to achieve 24 volts with 2
12 volt batteries would NORMALLY be called serial...

Where as to increase AMPACITY ... called "parallel."


Rather than risk severe burn, blindness (end of life
experimenting with EXPLOSIVES...
You need to go back to your source for better information ...
or
Provide better information here... Pretty please

Jan 12, 2017 | Electric Health & Beauty

1 Answer

I have an older craftsman 14.4 volt cordless drill limited edition the batteries are charged up but the drill has low power is there a fix?


new battery, when you said "batteries" you meant 1 battery pack right? more than likely its faulty or no longer any good- it also could be the charger and not the battery so test them both-----you can not fix a battery- you can try conditioning it but probably wont help--google if your unsure how to do that... good luck questions just ask

Mar 30, 2013 | Drills

2 Answers

Chevy Suburban 1500 -- Battery Not Charging Light....Replaced Alternator....Still had battery not charging light....Replaced battery....Still have battery not charging light...also first time seen service...


Make sure that you buy a 'lifetime' warranted alternator from your parts source to avoid problems with bad alternators out of the box. I would try to return and exchange the alternator with one that tests out ok on a bench, in order to verify if the wiring in between the alternator or the alternator itself was bad.

Service brake booster would have to do with the vacuum or power booster problem around the master cylinder for the braking system. That wouldn't have anything to do with the alternator, I do not believe.

Good luck on these repairs.

Jan 08, 2011 | 2003 Chevrolet Suburban 1500

2 Answers

Battery appears to be dead.. Plugged it in and no power.. completely dead and no way to recharge battery. Unsure if cord is bad or if its battery only. Norelco shaver 5885 XL model.


It is very unlikely that the cord is bad unless it has been severely stressed. Most likely, the problem is the battery but it is impossible for me to say for sure.
You will find the correct replacement battery pack for model 5885XL at shaveroutlet.com. See link below

http://shaveroutlet.com/shaver-replacement-parts/shaver-battery-pack-for-most-norelco-more-p-278.html

Jan 02, 2011 | Norelco Reflex Shaver 5885XL

2 Answers

Need to change the batteries in a Stanley bar flex light. lost instructions. how do you change the batteries.


I know this thread is old, but I just had to change the battery pack in mine. I could not locate a 4 pin battery pack so here's what I did:

You'll need: 3 NiMH 1.2v AA solder tab batteries, Razor blade, #1 Phillips driver, Kapton tap (standard electrical tape will do), soldering gun/iron, spare 18awg wire
1. Use a razor blade to remove the black sticker from the bottom of the flashlight base, it covers the magnets
2. remove the three outer phillips screws (the inner ones hold the magnets in and can stay installed)
3. Pull off the bottom plate
4. Pull out the battery pack and disconnect it from the flashlight at the 4-pin queeze connector
5. Remove the outer wrap and end protectors from the old pack keeping the end protectors in tact
6. Assemble the 3 new batteries in the same configuration as the old pack using Kapton tape, connecting + to - at the same two spots (use the old pack as a reference)
7. Carefully desolder the 2 wire leads from the old battery pack
8. connect up the 2 power wires to the same two spots as the old pack and insert the temperature probe between two of the batteries as in the old pack
9. Put the end caps on the new pack and wrap the entire thing in Kapton tape to simulate the plastic wrapper you removed
10. Install pack in to base, secure bottom plate and re-adhere black sticker(if needed you can use non-foam double-sided tape or spray adhesive)

The old pack was rated at 1300mAh and I used three 2000mAh each for a total of 6000mAh so theoretically the light should run for about 6 times as long between charges.

Aug 28, 2010 | Garden

1 Answer

How to replace hard drive


Hi tstafford,

Before you begin any removal or installation procedures:
1. Shut down the notebook. If you are unsure whether the
notebook is off or in hibernation, turn the computer on,
and then shut it down through the operating system.
2. Disconnect all external devices connected to the notebook.
3. Disconnect the power cord.
4. Remove the battery pack by following these steps:
a. Turn the notebook upside down with the front toward you.
b. Slide and hold the battery release latch 1 to the left.
(The front edge of the battery pack disengages from the
notebook.)
c. Lift the front edge of the battery pack 2 and swing
it back.
d. Remove the battery pack.
NOTE:
Reverse the above procedure to install the battery pack.

5. Loosen the two PM2.0×6.0 captive screws 1 that secure the hard drive cover to the notebook.

821796e.jpg

6. Lift the right side of the cover 2 and swing it to the left.
7. Remove the hard drive cover.
5. Grasp the mylar tab 1 on the hard drive and lift the hard
drive until it disconnects from the notebook.
6. Slide the hard drive 2 to the left and remove it from the hard drive bay.

1b7a96c.jpg
7. Remove the four PM3.0×4.0 screws 1 that secure the
hard drive frame to the hard drive.
8. Lift the frame 2 straight up to remove it from the hard drive.
9. Slide the hard drive connector 3 off the hard drive.

See Below: Reverse the procedures to install:

d1b4712.jpg

Good Luck, and don't forget to leave a rating.

Thanks

Mark

Oct 17, 2009 | HP 418446-001 - HP Special Edition L2000...

2 Answers

My battery will not hold a charge. I suspect it is the alternator, but at $269.00 I would like to know if there is something else that could cause this?...he battery has been replaced.


what you do is uhook alternater wires and tape let car sit and see, if battery goes dead then thats not the problem. also have charging system and battery checked first. hope this helps.

Oct 09, 2009 | 2006 Chevrolet Impala

1 Answer

Shifter will not shift out of park unless you uhook battery


there is a sensor on the ignition key switch, check it

Dec 13, 2008 | 1997 Chevrolet C1500

1 Answer

Forgot bios password


1. Shut down the computer. If you are unsure whether the
computer is off or in Hibernation, turn the computer on,
and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power cord.
4. Remove the battery pack by following these steps:
a. Turn the computer upside down with the front panel
toward you.
b. Slide and hold the battery release latch 1 to the left. (The
front edge of the battery pack disengages from the
computer.)
c. Lift the front edge of the battery pack 2 and swing it
back.
d. Remove the battery pack.
5. Remove the RTC battery from the socket on the system
board.
6. Wait approximately 5 minutes.
7. Replace the RTC battery and reassemble the computer.
8. Connect AC power to the computer. Do not reinsert any
battery packs at this time.
9. Turn on the computer.
All passwords and all CMOS settings have been cleared.

May 07, 2008 | HP Compaq Presario V2000 Notebook

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

194 people viewed this question

Ask a Question

Usually answered in minutes!

Top Transport Experts

yadayada
yadayada

Level 3 Expert

74242 Answers

Robin Hill
Robin Hill

Level 3 Expert

1262 Answers

Gregg Mahin
Gregg Mahin

Level 3 Expert

39035 Answers

Are you a Transport Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...