Question about Harley Davidson XL 1200 C Sportster Custom Motorcycles

1 Answer

Hazard lights are flashing, unable to start bike.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 8,909 Answers

I would say that the alarm works!
Switch off the alarm and it should start.

Posted on Nov 15, 2010

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Why do the lights stay on and why is there hazard lights on this bike

Don't know about your particular model, but some bikes do have the lights wired through the ignition so they are on permanently once the ignition turned on and this would leave the usual right hand switch as a spare. Would make sense to utilise it for the hazards.

Nov 17, 2015 | Hyosung GT 250 Motorcycles

2 Answers

Hazards are flashing all the time

It could be defective Hazard flasher connector or short circuit.

Dec 09, 2014 | Volkswagen Cars & Trucks

1 Answer

My honda cbr125cc will not start, the pgm-fi light is flashing red. Could this be the cause?

try charging the battery or replacing it, change the spark plugs and check the fuses to see if any are burned out.

Mar 02, 2014 | Motorcycles

1 Answer

I have a problem with my hazard relay it is the second one that went on my hyosung gt250r in one week. I replaced it with an origenal part from hyosungsource but the relay starts clicking as soon as I...

You have a crossed wire someplace in your wireharness. go back to the dealer and make them change it - it should be under warranty if you bought it new.

Jan 06, 2012 | 2009 Hyosung GT 250

1 Answer

I have 1986 Yamaha Venture. I took the luggage bags off to have the rear tire replaced by dealer. Picked up the bike and now I have no signal lights front or back. The front bulbs are working but do not...

The front lights are running lights and turn you are probably seeing the running light lit, as it should be any time the key is on.
The power for the turn signals goes through the Hazard flasher switch, its set up so you can't try the turn signals and the hazard flashers at the same time. First inspect to see the harness is still firmly connected to the switch.
I would remove the hazard flasher switch and with harness still attached, key ON, the Hazard switch OFF, verify you have battery voltage at the Brown wire.....thats from the Signal fuse circuit. If its check the brown/yellow wire for voltage...thats from the switch going to the flasher system...if no have a problem in the switch. A great site for Venture repair is the site.
Hope this has helped!

Sep 22, 2011 | Yamaha XJR 1300 Motorcycles

1 Answer

The hazard lights start flashing and I can't turn

there must be alarm fitted that either has the siren disconnected or turned off. Basically sensing an intrusion alert or voltage drop. Flip out the hazard switch, there will be a wire which runs seperate from the body loom into this light, just cut it, the correct one though. if needs be trace it back.....probably end up behind the glove box

Oct 03, 2009 | 1995 BMW 5 Series

1 Answer

Turn signals, Hazard lights

I would replace the bar switch assembly.

May 18, 2017 | 1998 Jeep Wrangler

1 Answer

Flashing Unit for Indicators Replacement

Most likely it's the hazard switch - the relay for the hazards and the turn signals is built into it. When they start to die, you will see erratic behavior with the turn signals and/or hazards, and eventually they'll both fail completely. Replace your hazard switch on the dash and you'll be good to go.

Aug 31, 2008 | 2000 Audi TT

1 Answer

Hazard and turn signal

Under the dash is a flasher unit. Replace it and everything should start working again. The flasher unit is very inexpensive and available at most parts stores.

Jul 02, 2008 | 1996 Buick Riviera

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

205 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Gills Lango

Level 2 Expert

195 Answers


Level 3 Expert

4336 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides